FHG-2000TK - Heat gun Ferm - Free user manual and instructions

Product Type	Heat Gun
Model	FHG-2000TK
Brand	Ferm
Voltage	230 V~
Frequency	50 Hz
Power Input	2000 W
Weight	1.6 kg
IP Class	IP20
Airflow (Position I)	300 l/min
Air Temperature (Position I)	450 °C
Airflow (Position II)	500 l/min
Air Temperature (Position II)	600 °C
Switch Positions	0 (Off), I (450°C, 300 l/min), II (600°C, 500 l/min)
Safety Class	Class II (Double insulation)
Included Accessories	Deflector nozzle, Fishtail nozzle, Air reducer nozzle, Scraper nozzle, Paint scraper, Instruction manual, Safety instructions, Warranty card
Product Dimensions	Not specified in manual
Maintenance	Keep ventilation slots clean; disconnect before cleaning
Overheating Protection	Automatic thermal cutoff (heater switches off, fan continues)
Certifications	CE, EN60335-1, EN60335-2-45, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3, 98/37/EC, 73/23/EEC, 89/336/EEC, 2002/95/EC, 2002/96/EC

Frequently Asked Questions - FHG-2000TK Ferm

What is the maximum temperature of the Ferm FHG-2000TK heat gun?

The maximum temperature is 600 °C in position II.

Can I use the heat gun for drying hair?

No, do not use the appliance for drying hair or drying living human beings. It is designed for industrial and DIY applications only.

How do I switch between temperature settings?

Use the slide switch. Position '0' is off, 'I' for 450°C (300 l/min), and 'II' for 600°C (500 l/min).

What should I do if the heat gun stops heating but the fan still runs?

This is normal: the thermal protection switches off the heater if it gets too hot. Let it cool down; it will automatically restart.

What accessories are included with the FHG-2000TK?

Included: deflector nozzle, fishtail nozzle, air reducer nozzle, scraper nozzle, paint scraper, instruction manual, safety instructions, and warranty card.

How do I clean the heat gun?

Always disconnect from power before cleaning. Keep ventilation slots clean to prevent overheating. Do not use water or flammable liquids on electrical parts.

Can I use an extension cord?

Yes, use an approved extension cable with a minimum conductor size of 1.5 mm². Unwind the reel completely.

What safety precautions should I take while using the heat gun?

Avoid touching the metal nozzle (it gets very hot). Do not block the air outlet. Keep children and animals away. Do not use near flammable liquids or in wet areas.

What can I use the heat gun for?

Applications include paint stripping, thawing pipes, bending plastics, shrink-wrapping, removing adhesives, and soldering.

What does the deflector nozzle do?

The deflector nozzle directs hot air away from glass or delicate surfaces, useful for stripping paint from window frames or softening putty.

USER MANUAL FHG-2000TK Ferm

GB Subject to change

Black hard-shell portable tool kit with open case (no visible text or symbols)

CE

www.ferm.com

CE

DECLARATION OF CONFORMITY

FHG-2000TK HOT AIR GUN

(GB) We declare under our sole responsibility that this product is in conformity and accordance with the following standards and regulations:
(D) Der Hersteller erklärt eigenverantwortlich, dass dieses Produkt den folgenden Standards und Vorschriften entspricht:
(NL) Wij verklaren onder onze volledige verantwoordelijkheid dat dit product voldoet aan, en in overeenstemming is met, de volgende standaarden en reguleringen:
(F) Nous déclarons sous notre seule responsabilité que ce produit est conforme aux standards et directives suivants:
(E) Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con las siguientes normas y estándares de funcionamiento:
(P) Declaramos por nossa total responsabilidade que este produto está em conformidade e cumpre as normas e regulamentações que se sequem:
(I) Dichiariamo, sotto la nostra responsabilità, che questo prodotto è conforme alle normative e ai regolamenti seguenti:
(S) Vi garanterar på eget ansvar alt denna produkt uppfyller och följer följande standarder och bestämmelser:
(FIN) Vakuutamme yksinomaan omalla vastuullamme, että tämä tuote tävitää seuraavat standardit ja säädökset:
(N) Vi erklærer under vart eget ansvar af dette produktet er i samsvar med folgende standarder og regler.
(DK) Vi erklærer under øget ansvar, at dette produkt or overensstemmelse med folgende standarder og bestemmelser:

(H) Felelőssógünk teljes tudatában kjelentjük, hogy ez a termék teljes mérlékben megfelel az alábbi szabványoknak és előirásoknak:
(CZ) Na naši vlastní zodpovědnost prohlašujeme, že je tento výrobek v souladu s následujícími standardy a normami:
(SK) Výnlasujeme na našu výhradnú zodpovednosť, že tento výrcbok je v zhode a súlade s nasledujúcimi normami a predpismi:
(SLO) Š polno odgovornostjo izjavijamo, da je ta izdelek v skladu in da odgovarja naslednjim standardom ter predpisom:
(PL) Deklarujemy na własną odpowiedzialność, że ten produkt spełnia wymogi zawarte w następujących normach i przecisach:
(LT) Prislimdami visą atsakomybę deklaruojame, kad śis gaminys abitinka żemiau paminētus standartus arba nuostatus;
(LV) Apgalvojam ar visu atbildību, ka šis produkts ir saskaņa un atbilst sekojošiem standartiem un nolikumiem:
(EST) Deklareerime meie ainuvastutusel, et see toode on vastavuses ja kocskõlas järgmiste standardite ja määrustega:
(RO) Declaram prin aceasta cu răspunderea deplină că produsul acesta este în conformitate cu următoarele standarde sau directive:
(RUS) Под свою ответственность заявляем, что данное изделие соответствует следующим стандартам и нормам:
(UA) На свою власну відповідальність заявляєю, що дане обладнання відповідає неступним стандартам і нормативами:
(GR) Δηλώνουμα υπεύθυνα ότι το προϊόν αυτό συμσωνεί και τηρεί τους παρακάτα κανονισμους και πρότυπα:

EN60335-1, EN60335-2-45, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3

98/37/EC, 73/23/EEC, 89/336/EEC, 2002/95/EC, 2002/96/EC

Zwolle, 01-04-2007

J.A. Bakker - van Ingen CEO Ferm BV

J. Lodewijk Quality Manager Ferm Global

It is our policy to continuously improve our products and we therefore reserve the right to change the product specification without prior notice.

Ferm BV • Lingenstraat 6 • 8028 PM • Zwolle The Netherlands

Ferm 7102 Ferm

HOT AIR GUN

The numbers in the following text correspond with the pictures at page 2

Always read the instruction for electrical products carefully before use. It will help you understand your product more easily and avoid unnecessary risks. Keep this instruction manual in a safe place for future use.

Contents

1. Machine data
2. Safety Instructions
3. Using the appliance
4. Maintenance

1. MACHINE DATA

Technical specifications

Voltage 230 V\~ Frequency 50 Hz Power input 2000 W Weight 1.6 kg IP Class IP 20 Position I Air flow 300 l/min Air temperature 450 °C Position II Air flow 500 l/min Air temperature 600 °C

Contents of packing

1 Hot air gun
1 Deflector nozzle
1 Fishtail nozzle
1 Air reducer nozzle
1 Scraper nozzle
1 Paint scraper
1 Instruction manual
1 Safety instructions
1 Warranty card

Product information

Fig. A

1. Switch
2. Ventilation slots
3. Nozzle outlet

2. SAFETY INSTRUCTIONS

Explanation of the symbols

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.

Indicates electrical shock hazard.

Additional safety instructions

When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury. Read all these instructions before attempting to operate this product and save these instructions.

Before using the appliance

• Check the following:
  • Make sure the voltage of the hot air gun
  corresponds with the power voltage;
• Are the mains lead and the mains plug in a good state: strong, without ravels or damages.
• Avoid the use of long extension cables;
• Do not use the appliance under moist circumstances;
  • The metal mouthpiece gets hot. Watch out and do not touch the metal mouthpiece;
• Prevent damage of the heating element. Do not lock or block the mouth piece;
• Do not leave the appliance when switched on;
• Do not use the appliance for drying hair or for drying living human beings in general:
• Do not use the appliance in a bath, above water or in spaces where easy inflammable liquids are used.

This appliance operates at a temperature of 600 degrees without visible signs of this temperature (no flames), still there is a chance of fire risk. Watch out for the hot air stream from the mouth piece. This air stream can cause burns.

When operating the appliance

- If you are going to use the hot air gun, vapours and gas can be released during a short time. This can be harmful for your health. Asthmatics can suffer hindrance of it;

• Before connecting the plug to the mains voltage you have to check if the switch is in position "0":
• Keep the mains lead always away from the mouthpiece of the hot air gun;
• Keep children and animals away from the appliance if you are using it.

Immediately switch off the appliance when:

- Plug and/or cable are defective or damaged;

• The switch is defective;

- You smell or see smoke caused by scorched insulation from the hot air gun.

Electrical safety

When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and also the enclosed safety instructions.

Always check that the power supply corresponds to the voltage on the rating plate.

Class II machine – Double insulation – You don't need any earthed plug

Replacing cables or plugs

Immediately throw away old cables or plugs when they have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet.

Using extension cables

Only use an approved extension cable suitable for the power input of the machine. The minimum conductor size is 1.5 mm². When using a cable reel always unwind the reel completely.

3. USING THE APPLIANCE

The Hot air gun can be used for:

• Plumbing work like tube connections, solder, bowing tubes;
• Removing paint, varnish and lacquer without firerisk;

• Quickly drying of appliances which have become wet;
  • Drying surfaces for quick repairing;

• Removing self-adhesive labels in a clean way placing PVC labels;

• Blistering after sticking PVC materials can be smoothed after heating;
• Easy removing of vinyl carpeting:
• Forming all synthetics with a low temperature (450 degrees) among which polyethylene and PVC;
• Forming all synthetics with a high temperature (580 degrees) among which acryl and plexiglass;
• Smelting synthetics, among which matters and foils with PVC layer;
  • Applying heat shrinking tubes;
• Shrinkwrappers;
  • Thawing tubes and engines;
  • Repairing finishing layers: email of bath and household appliances:
  • Applying epoxypowder coverlayers;
  • Repairing of ski's, surf-boards and other sports goods;
• Unscrewing too fast fixed screws and connections.

Operation

Fig. A

You can work manually with this hot air gun or you can put it in a vertical position.

- Check if the mains switch is on position "0" before you connect the apparatus:

- Keep the main lead always away from the hot air stream and the mouth piece:

- Put the mains switch in position 'I or II' to let your hot air gun operate:

"1" = 450 degrees, air flow 300 l/min.

"0" = Off

“2” = 600 degrees, air flow 500 l/min.

When the temperature is excess 600^ , the heats switches it off automatically, however, the heater continues to run. When the heater has cooled to operating temperature, the heater is switched on again.

Switching off:

Slide the switch to 0.

Tip: If you want to get the best result, test all appliances on a little part of the workpiece.

Deflects air away from glass for example when stripping paint in window frames or softening putty.

Scraper nozzle (5)

This is used to scrape and strip paint.

Air reducer nozzle (6)

Use this when intensified heat is needed in a specific area. Like corners and small spaces.

Fishtail nozzle (7)

Distributes air equally over small areas

Paint scraper (8)

Use this tool to scrape paint.

4. MAINTENANCE

Always disconnect the apparatus before carrying out inspection or cleaning. Never use water or other liquids to clean the electrical parts of the hot air gun.

• Never use easy inflammable liquids for cleaning the hot air gun, especially for the mouthpiece.
• Regular maintenance of your hot air gun prevents unnecessary problems. Keep the ventilation slots of the hot air gun clean to prevent overheating.

Troubleshooting

In case the hot air gun does not work well, we give you subjoined some possible causes and their solutions.

• The engine gets overheated.

• The ventilation slots of the hot air gun are dirty.
• Clean the ventilation slots.

• The hot air gun does not start when it is switched on.

• Interruption in the electrical circuit.
• Check the mains lead and the mains plug.

• The switch is defective.

- Pull the mains lead out of the wall socket, because there is a chance of fire risk! Have the hot air gun repaired at your local dealer.

• The engine does not work, but it does heat.

- Interruption in the electrical circuit.

- Pull the mains lead out of the wall socket, because there is a chance of fire risk! Have the hot air gun repaired at your local dealer.

Faults

Should a fault occur, e.g. after wear of a part, please contact the service address on the warranty card. In the back of this manual you find an exploded view showing the parts that can be ordered.

Environment

To prevent damage during transport, the appliance is delivered in a solid packaging which consists largely of reusable material. Therefore please make use of options for recycling the packaging.

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

Guarantee

The guarantee conditions can be found on the separately enclosed guarantee card.

HEISSLUFTGEBLÄSE

- Storing in de netstekker, netsnoer of snoerbeschadiging.

Specifications techniques