FHG-2000 - Heat gun Ferm - Free user manual and instructions
Find the device manual for free FHG-2000 Ferm in PDF.
| Product Type | Hot Air Gun (Heat Gun) |
| Brand | Ferm |
| Model | FHG-2000(K) |
| Voltage | 230 V ~ |
| Frequency | 50 Hz |
| Power Input | 2000 W |
| Temperature Range | Position I: 320 °C, Position II: 580 °C |
| Air Flow | Position I: 500 l/min, Position II: 650 l/min |
| Switch Positions | 0 (Off), I (Low), II (High) |
| Nozzles Included | 4 mouthpieces + 1 paint scraper |
| Stand Capability | Freestanding with stand at 90° to handle |
| Safety Features | RCD recommended, earthed plug, thermal overload protection |
| Cleaning | Soft brush or dry cloth; do not use flammable liquids |
| Spare Parts Available | Enclosure, metal frame, fan motor, heating element, switch, capacitor (refer to parts list) |
| Guarantee | Separate guarantee card included |
| CE Mark | Yes (UKCA/CE declaration) |
| Environmental | Recycle at end of life |
Frequently Asked Questions - FHG-2000 Ferm
User questions about FHG-2000 Ferm
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Heat gun in PDF format for free! Find your manual FHG-2000 - Ferm and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. FHG-2000 by Ferm.
USER MANUAL FHG-2000 Ferm
UK Subject to change
USER'S MANUAL
Ferm Hot-Air Gun
FHG-2000(K)
Ferm®
Art.nr. 785700
Art.nr. 785705
Screwfix art.nr: 12296
FERM HOT-AIR GUN FHG-2000(K) USERS MANUAL
TECHNICAL SPECIFICATIONS
Voltage | 230 V \~
Frequency | 50 Hz
Power input | 2000 W
Heat capacity position | 1320°C/
| 500 l/min
Heat capacity position I | 580 °C/
| 650 l/min
PRODUCT INFORMATION
I Hot-air gun
4 Mouthpieces
I Paintscraper
I Users manual
I Garanty card
ELECTRICAL INFORMATION
This product is complete with a pre-wired mains plug. If the plug needs replacing follow these instructions.
Wire correctly
The wires in the mains lead are coloured in the following
Blue -Neutral
BEOE -Neutral BROWN -Live
GREEN/YELLOW -Earth
Secure wires
Secure wires carefully and firmly to the correct terminals. Secure the mains cable in the plug cord grip firmly Fit a 13 amp fuse. If a 13amp (BS1363) plug is used a (BS 1362) ASTA approved 13-amp fuse must be fitted.
Recycle/Dispose of old plug and cable
Prevent inadvertent connection to socket and risk of electric shock.
If in doubt always consult a Qualified Electrician
SAFETY INSTRUCTIONS
The following pictograms are used in these instructions for use:
Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the risks in this manual.
Denotes risk of electric shock.
Denotes risk of fire.
Carefully read this manual before using the machine. Make sure that you know how the machine functions and how to operate it. Maintain the machine in accordance with the instructions to make sure it functions properly. Keep this manual and the enclosed documentation with the machine.
Ferm products are manufactured to high quality standards they are safe and fit for purpose at time of sale, but all tools can be dangerous if the correct precautions are not taken. Always follow these instructions, do not carry out the operation until you are sure you can do so in safety. Remember to consider the work environment for safe operation as well as safety for tool use.
Warning! When using electric tools, basic safety precautions should always be followed to reduce of fire, electric shock and personal injury. Read all instructions before attempting to operate this product. Use instructions for future reference.
PERSONALSAFETY
Use Personal Protection Safety Equipment
Protect eyes with safety glasses or goggles note: the use of safety protective eyewear without the CE mark can lead to serious injury if the glass breaks. A suitable dust mask should be worn if cutting, drilling or sanding is dusty, in particular chipboard or MDF. Approved safety footwear and headgear should worn as appropriate, for example on building works or when heavy weights are involved.
Dress properly
Do not wear loose clothing or jewellery. It can get caught in moving parts. Non-skid footwear is recommended when working out doors. Wear protective hair covering to contain long hair.
Stay alert
Watch what you are doing Use common sense. Do not operate tools when tired or after taking alcohol or prescription/non-prescription drugs.
EXPLODED VIEW
SPARE PARTS FHG-2000(K)
| REF.NR. DESCRIPTION FERM NR. | ||
| 1 | ENCLOSURE (COMPLETE) | 104080 |
| 2 | METAL FRAME FOR ELEMENT SUUPORT | 104081 |
| 3 | FAN MOTOR | 104082 |
| 4 | HEATING ELEMENT | 104083 |
| 5 | SWITCH | 104084 |
| 6 | CAPACITOR 0,1 μF | 104085 |
OPERATIONAL SAFETY
Warning! The hot air gun operates at a temperature of 580 degrees without visible signs of heat. Be
careful: the hot air stream and the mouthpiece are very hot and can cause burns.
Be aware that the hot air stream is a fire risk although no flames are visible. Do not touch the mouthpiece or point it at yourself.
Do not leave the hot air gun unattended when switched on. Do not use for drying hair, animals or on any living thing.
Keep the hot air gun away from children and animals Do not use the hot air gun in a bath, near water or inflammable liquids.
Concentrate
Routine and repetition can lead to mistakes. Remember that a slight lack of concentration can result in serious injuries in a split second.
Keep work area clean
Cluttered areas and benches invite injuries
Consider the work environment
Do not expose power tools to rain or use them in damp or wet locations. Keep work area well lit. Do not use power tools in the presence of flammable liquids, vapours or gases.
Guard against electric shock
This unit contains dangerous voltages. Use a RCD (residual current device) to provide protection against electrical shock. Prevent body contact with grounded surfaces (e.g. pipes, radiator, ranges or refrigerators).
Keep children and pets away
Do not let children or pets come into contact with the tool, extension cable or work area.
Do not force the tool
It will work better and safer at the rate for which it was intended.
Use the right tool
Do not force small tools or attachments to do the job of a heavy-duty tool. Do not use tools for purposes for which they were not intended; for example do not use a circular saw for cutting trees or logs.
Do not abuse cable
Never carry the tool by the cable or pull it to disconnect it from the power socket. Keep the cable away from heat, oil and sharp edges. Do not touch the metal plug pins when connecting or removing the plug.
Secure Work
Use clamps or a vice to hold work. It is safer than using your hand and it frees both hands to operate the tool.
Do not over-reach
Keep a proper footing and balance at all times.
Disconnect tools from power supply
When not in use, before servicing and when changing accessories such as blades, bits and cutters. Always switch off and unplug the hot air gun from the power supply before making adjustments or changing nozzles.
Remove adjusting keys and wrenches
Ensure that they are removed from the tool before switching on.
Avoid unintentional starting
Do not carry plugged in tools with your finger on the switch. Check that the switch is off before plugging in to socket.
Extension cables
Use only three core earthed extension cables suitable for the power input of the tool (minimum cable size 1.5mm2). Plug into an earthed socket only.
When using a cable reel unwind it fully. Do not use long extension cables.
Outdoors use
If the tool is suitable to be used outdoors, only use an extension cable intended for outdoor use and marked accordingly. Use a RCD (residual current device) to provide protection against electrical shock. Do not use in rain or damp conditions.
Connect a dust extraction device
Whenever there are facilities for fitting a dust of fume extraction system, make sure it is connected and used.
Use recommended accessories
The use of any other accessory or attachment other than recommended in the instructions or catalogue may present a risk of personal injury. Do not use long extension cables with the hot air gun.
USING THE HOT AIR GUN
- Before operating check the voltage on the hot air gun corresponds with your power supply voltage and that the plug and lead are in good condition.
- Check that the switch is in position"0"
- Attach the adaptor (if supplied) to the nozzle before switching on.
- Operation Plug into a suitable mains supply and switch on.
- To switch ON put the switch on the hot air gun to position: - "I" for lower heat and air flow – 320 degrees/500 litres air per minute
- "II" for higher heat and air flow – 580 degrees/650 litres air per minute
- The hot air gun can be used either hand held or free-standing with the stand set at 90 degrees to the handle.
- To switch OFF put the switch in position "O"
- To determine suitability or find the best heat setting, test on a piece of scrap or small area of the work piece that will not be seen. Start off at position "I" low setting.
MAINTENANCE, CARE AND REPAIR
CLEANING
Clean with a soft brush or dry cloth.
Do not use flammable liquids to clean the saw they can damage the plastic parts and the finish.
Do not use flammable liquids to clean the hot air gun
FAULTS
Switch OFF immediately at the mains plug and remove the plug when:
- The plug or cable is damaged.
- The switch on the machine is defective.
- You smell or see smoke caused by scorched insulation in the machine
Overheating
The ventilation slots are blocked with dirt. Clean with dry cloth.
The hot air gun does not start when switched on
- Check the mains lead and the fuse/plug.
- Take to your Ferm Dealer for repair
The motor is defective
Take to your Ferm Dealer
MAINTAIN TOOLS WITH CARE
Keep the tool clean for better and safer performance.
Follow instructions for changing accessories. Inspect tool and extension cables periodically and if damaged, have them repaired by a qualified person or authorised service body. Keep handles free from oil or grease. Keep the ventilation slots clean to prevent motor overheating.
Check for damaged parts
Do not use a tool with damaged parts, before further use a damaged tool must be carefully checked by a qualified person to determine that it will operate properly. Check for alignment of moving parts, binding or breakage of parts, mounting and other conditions that may affect its operation.
A damaged part or guard should be properly repaired by an authorised service centre, unless indicated otherwise in the instruction manual. Have defective switches replaced by an authorised service centre. Do not use a tool if the switch does not turn on and off.
Have your tool repaired by an expert
This appliance is manufactured in accordance with relevant safety standards. Only experts must carry out repairing of electrical appliances, otherwise considerable danger for the user may result.
Storing tools
When not in use tools should be stored in the dry, out of reach of children.
ENVIRONMENT
At the end of this products or its accessories life please recycle where facilities exist - phone the Helpline for current advice on recycling.
GUARANTEE
The guarantee conditions can be found on the separately enclosed guarantee card.
CE DECLARATION OF CONFORMITY (UK)
We declare under our sole responsibility that this
product is in conformity with the following
standards or standardized documents
in accordance with the regulations:
73/23/EEG
89/336/EEG
From 01-05-2002
GENEMUIDEN NL
W. Kamphof
Quality department
For any queries relating to operational or safety matters contact:
Ferm Customer Helpline on: 0115 966 1199
Monday-Friday 8am-6pm
Saturday 9am–1 pm
- FERM HOT-AIR GUN FHG-2000(K) USERS MANUAL
- TECHNICAL SPECIFICATIONS
- PRODUCT INFORMATION
- ELECTRICAL INFORMATION
- Wire correctly
- Secure wires
- Recycle/Dispose of old plug and cable
- SAFETY INSTRUCTIONS
- PERSONALSAFETY
- Use Personal Protection Safety Equipment
- Dress properly
- Stay alert
- OPERATIONAL SAFETY
- Concentrate
- Keep work area clean
- Consider the work environment
- Guard against electric shock
- Keep children and pets away
- Do not force the tool
- Use the right tool
- Do not abuse cable
- Secure Work
- Do not over-reach
- Disconnect tools from power supply
- Remove adjusting keys and wrenches
- Avoid unintentional starting
- Extension cables
- Outdoors use
- Connect a dust extraction device
- Use recommended accessories
- USING THE HOT AIR GUN
- MAINTENANCE, CARE AND REPAIR
- CLEANING
- FAULTS
- Overheating
- The motor is defective
- MAINTAIN TOOLS WITH CARE
- Check for damaged parts
- Have your tool repaired by an expert
- Storing tools
- ENVIRONMENT
- GUARANTEE
- CE DECLARATION OF CONFORMITY (UK)
- From 01-05-2002
- GENEMUIDEN NL
Brand : Ferm
Model : FHG-2000
Category : Heat gun