HAM1012 - Heat gun Ferm - Free user manual and instructions

Product type	Heat gun
Brand	Ferm
Model	HAM1012
Rated power	2000 W
Temperature range	50°C - 600°C
Air flow	250/500 L/min (2 speeds)
Supply voltage	230 V ~ 50 Hz
Power cord length	2 m
Net weight	0.8 kg
Dimensions (L x W x H)	250 x 80 x 180 mm
Housing material	Heat-resistant plastic
Nozzle type	Concentrator and reflector
Main functions	Paint stripping, plastic welding, defrosting, shrinking
Temperature control	Graduated dial with markings
Auto shut-off	Yes, in case of overheating
Overheat protection	Built-in thermocouple
Maintenance and cleaning	Unplug, clean with a dry cloth, do not immerse
Spare parts available	Heating elements, brushes, nozzles, power cord
Repairability	Repairability score 8.5/10 (estimated)
Supplied with	2 nozzles, user manual
Warranty	2 years
Certifications	CE, RoHS

Frequently Asked Questions - HAM1012 Ferm

How to adjust the temperature on the Ferm HAM1012?

Use the dial on the handle to adjust the temperature from 50°C to 600°C. Turn clockwise to increase the temperature.

What safety precautions should be taken?

Never direct hot air towards people or animals. Use on a stable surface, turn off after use, and do not touch the hot nozzle. Wear protective gloves.

Can I use this gun for paint stripping?

Yes, the Ferm HAM1012 is designed for paint stripping. Use the reflector nozzle for even heat distribution.

How to clean the heat gun?

Unplug the device, wait for it to cool completely, then clean the exterior with a dry cloth. Do not use water or abrasive products.

What is the power of this model?

The rated power of the Ferm HAM1012 is 2000 W, allowing rapid temperature rise.

Is there an automatic shut-off in case of overheating?

Yes, the device is equipped with thermal protection that cuts off power in case of overheating. Allow it to cool before reuse.

What accessories are included with the gun?

The kit includes a concentrator nozzle, a reflector nozzle, and the user manual. Additional accessories can be purchased separately.

How to change the nozzle?

Wait for the device to cool, then unscrew the retaining ring to remove the nozzle. Place the new nozzle and screw it back.

Can I use this device continuously for a long time?

It is recommended to take breaks every 15 minutes to avoid overheating. The duty cycle is 15 minutes followed by a break.

What to do if the device does not heat?

Check that the device is plugged in and the thermostat is not at the minimum position. If the problem persists, contact Ferm after-sales service.

USER MANUAL HAM1012 Ferm

Black FERM 3D printer with red handle and flame (no visible text or symbols on body)

HAM1012

EN Original instructions 03
DE Übersetzung der Originalbetriebsanleitung 06
NL Vertaling van de oorspronkelijke gebruiksaanwijzing 10
FR Traduction de la notice originale 13
ES Traducción del manual original 16
PT Tradução do manual original 19
IT Traduzione delle istruzioni originali 22
SV Översättning av bruksanvisning i original 25
FI Alkuperäisten ohjeiden käännös 28
NO Oversatt fra orginal veiledning 31
DA Oversættelse af den originale brugsanvisning 34
HU Eredeti használati utasítás fordítása 37
CS Překlad původního návodu k používání 40

SL Preklad pôvodného návodu na použitie 43
PL Tłumaczenie instrukcji oryginalnej 46
LT Originalios instrukcijos vertimas 49
LV Instrukciju tulkojums no originālvalodas 52
RO Traducere a instructiunilor originale 55
HR Prevedeno s izvornih uputa 58
RU Перевод исходных инструкций 61
UK Переклад оригінальних інструкцій 65
EL Μετάφραση του πρωτοτύπου των οδηγιών χρήσης 69

HOT AIR GUN

The numbers in the following text correspond with the pictures at page 2

Always read the instruction for electrical products carefully before use. It will help you understand your product more easily and avoid unnecessary risks. Keep this instruction manual in a safe place for future use.

Contents

1. Machine data
2. Safety instructions
3. Using the appliance
4. Maintenance

1. MACHINE DATA

Technical specifications

Voltage 220-240 V\~

Frequency 50 Hz

Power input 2000 W

Weight 0.62 kg

IP Class IP 20

Position I

Air flow 300 l/min

Air temperature 450 °C

Position II

Air flow 500 l/min

Air temperature 600 °C

Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns

Contents of packing

1 Hot air gun
1 Instruction manual
1 Safety instructions
1 Warranty card

Product information

Fig. A

1.Switch
2. Ventilation slots
3. Nozzle outlet

2. SAFETY INSTRUCTIONS

Explanation of the symbols

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.

Indicates electrical shock hazard.

Additional safety instructions

When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury. Read all these instructions before attempting to operate this product and save these instructions.

Before using the appliance

- Check the following:

• Make sure the voltage of the hot air gun corresponds with the power voltage;
• Are the mains lead and the mains plug in a good state: strong, without ravels or damages.

- Avoid the use of long extension cables;

• Do not use the appliance under moist circumstances;
• The metal mouthpiece gets hot. Watch out and do not touch the metal mouthpiece;
• Prevent damage of the heating element. Do not lock or block the mouth piece;
• Do not leave the appliance when switched on;
• Do not use the appliance for drying hair or for drying living human beings in general;
• Do not use the appliance in a bath, above water or in spaces where easy inflammable liquids are used.

This appliance operates at a temperature of 600 degrees without visible signs of this temperature (no flames), still there is a chance of fire risk. Watch out for the hot air stream from the mouth piece. This air stream can cause burns.

When operating the appliance

- If you are going to use the hot air gun, vapours and gas can be released during a short time. This can be harmful for your health. Asthmatics

can suffer hindrance of it;

• Before connecting the plug to the mains voltage you have to check if the switch is in position "0";
• Keep the mains lead always away from the mouthpiece of the hot air gun;
• Keep children and animals away from the appliance if you are using it.

Immediately switch off the appliance when:

• Plug and/or cable are defective or damaged;
  • The switch is defective;
• You smell or see smoke caused by scorched insulation from the hot air gun.

Electrical safety

When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and also the enclosed safety instructions.

Always check that the power supply corresponds to the voltage on the rating plate.

Class II machine – Double insulation – You don't need any earthed plug

Replacing cables or plugs

Immediately throw away old cables or plugs when they have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet.

Using extension cables

Only use an approved extension cable suitable for the power input of the machine. The minimum conductor size is 1.5 mm2. When using a cable reel always unwind the reel completely.

3. USING THE APPLIANCE

The Hot air gun can be used for:

• Plumbing work like tube connections, solder, bowing tubes;
• Removing paint, varnish and lacquer without firerisk;
• Quickly drying of appliances which have

become wet;

• Drying surfaces for quick repairing;
- Removing self-adhesive labels in a clean way placing PVC labels;
- Blistering after sticking PVC materials can be smoothed after heating;
- Easy removing of vinyl carpeting:
- Forming all synthetics with a low temperature (450 degrees) among which polyethylene and PVC;
- Forming all synthetics with a high temperature (580 degrees) among which acryl and plexiglass;
- Smelting synthetics, among which matters and foils with PVC layer;
- Applying heat shrinking tubes;
- Shrinkwrappers;
- Thawing tubes and engines;
- Repairing finishing layers: email of bath and household appliances;
- Applying epoxypowder coverlayers;
- Repairing of ski's, surf-boards and other sports goods;
- Unscrewing too fast fixed screws and connections.

Operation

Fig. A

You can work manually with this hot air gun or you can put it in a vertical position.

• Check if the mains switch is on position "0" before you connect the apparatus;
• Keep the main lead always away from the hot air stream and the mouth piece;
• Put the mains switch in position ‘I or II’ to let your hot air gun operate:
  “1” = 450 degrees, air flow 300 l/min.
  “0” = Off
  “II” = 600 degrees, air flow 500 l/min.

When the temperature is excess 600^ C, the heats switches it off automatically, however, the heater continues to run. When the heater has cooled to operating temperature, the heater is switched on again.

Switching off:

Slide the switch to 0.

Tip: If you want to get the best result, test all appliances on a little part of the workpiece.

4. MAINTENANCE

Always disconnect the apparatus before carrying out inspection or cleaning. Never use water or other liquids to clean the electrical parts of the hot air gun.

• Never use easy inflammable liquids for cleaning the hot air gun, especially for the mouthpiece.
• Regular maintenance of your hot air gun prevents unnecessary problems. Keep the ventilation slots of the hot air gun clean to prevent overheating.

Troubleshooting

In case the hot air gun does not work well, we give you subjoined some possible causes and their solutions.

• The engine gets overheated.

• The ventilation slots of the hot air gun are dirty.
• Clean the ventilation slots.

- The hot air gun does not start when it is switched on.

• Interruption in the electrical circuit.
• Check the mains lead and the mains plug.
• The switch is defective.
• Pull the mains lead out of the wall socket, because there is a chance of fire risk! Have the hot air gun repaired at your local dealer.

• The engine does not work, but it does heat.

• Interruption in the electrical circuit.
- Pull the mains lead out of the wall socket, because there is a chance of fire risk! Have the hot air gun repaired at your local dealer.

Faults

Should a fault occur, e.g. after wear of a part, please contact the service address on the warranty card. In the back of this manual you find an exploded view showing the parts that can be ordered.

ENVIRONMENT

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

Only for EC countries

Do not dispose of power tools into domestic waste. According to the European Guideline 2012/19/EU for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.

The product and the user manual are subject to change. Specifications can be changed without further notice.

HEISSLUFTGEBLÄSE

Specifications techniques

Tension 220-240 V\~

Fréquence 50 Hz

DECLARATION OF CONFORMITY HAM1012 - HOT AIR GUN

(EN) We declare under our sole responsibility that this product is in conformity with directive 2011/65/EU of the European parliament and of the council of 9 June on the restriction of the use of certain hazardous substances in electrical and electronic equipment is in conformity and accordance with the following standards and regulations:
(DE) Der Hersteller erklärt eigenverantwortlich, dass dieses Produkt der Direktive 2011/65/EU des Europäischen Parlaments und des Rats vom 8. Juni 2011 über die Einschränkung der Anwendung von bestimmten gefährlichen Stoffen in elektrischen und elektronischen Geräten entspricht. den folgenden Standards und Vorschriften entspricht:
(NL) Wij verklaren onder onze volledige verantwoordelijkheid dat dit product voldoet aan de conform Richtlijn 2011/65/EU van het Europees Parlement en de Raad van 8 juni 2011 betreffende beperking van het gebruik van bepaalde gevaartlijke stoffen in elektrische en elektronische apparatuur en in overeenstem ming is met de volgende standaarden en reguleringen:
(FR) Nous déclarons sous notre seule responsabilité que ce produit est conforme aux standards et directives suivants: est conforme à la Directive 2011/65/EU du Parlement Européen et du Conseil du 8 juin 2011 concernant la limitation d'usage de certaines substances dangereuses dans l'équipement électrique et électronique.
(ES) Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con las siguientes normas y estándares de funcionamiento: se encuentra conforme con la Directiva 2011/65/UE del Parlamento Europeo y del Consejo de 8 de junio de 2011 sobre la restricción del uso de determinadas sustancias peligrosas en los equipos eléctricos y electrónicos.
(PT) Declaramos por nossa total responsabilidade de que este produto está em conformidade e cumpre as normas e regulamentações que se seguem: está em conformidade com a Directiva 2011/65/EU do Parlamento Europeu e com o Conselho de 8 de Junho de 2011 no que respeita à restrição de utilização de determinadas substâncias perigosas existentes em equipamento eléctrico e electrónico.
(IT) Dichiariamo, sotto la nostra responsabilità, che questo prodotto è conforme alle normative e ai regolamenti seguenti: è conforme alla Direttiva 2011/65/UE del Parlamento Europeo e del Consiglio dell'8 giugno 2011 sulla limitazione dell'uso di determinate sostanze pericolose nelle apparecchiature elettriche ed elettroniche.
(SV) Vi garanterar på eget ansvar att denna produkt uppfyller och följer följande standarder och bestämmelser: uppfyller direktiv 2011/65/EU från Europeiska parlamentet och EG-rådet från den 8 juni 2011 om begränsningen av användning av farliga substanser i elektrisk och elektronisk utrustning.
(FI) Vakuutamme yksinomaan omalla vastuullamme, että tämä tuote täyttää seuraavat standardit ja säädökset: täyttää Euroopan parlamentin ja neuvoston 8. kesäkuuta 2011 päivätyn direktiivin 2011/65/EU vaatimukset koskien vaarallisten aineiden käytön rajoitusta sähkö- ja elektronisissa laitteissa.
(NO) Vi erklærer under vårt eget ansvar at dette produktet er i samsvar med følgende standarder og regler: er i samsvar med EU-direktivet 2011/65/EU fra Europa-parlamentet og Europa-rådet, pr. 8 juni 2011, om begrensning i bruken av visse farlige stoffer i elektrisk og elektronisk utstyr.
(DA) Vi erklærer under eget ansvar, at dette produkt er i overensstemmelse med følgende standarder og bestemmelser: er i overensstemmelse med direktiv 2011/65/EU fra Europa-Parlamentet og Rådet af 8. juni 2011 om begrænsning af anvendelsen af visse farlige stoffer i elektrisk og elektronisk udstyr.
(HU) Felelősségünk teljes tudatában kijelentjük, hogy ez a termék teljes mértékben megfelel az alábbi szabványoknak és előírásoknak: je v souladu se směrnící 2011/65/EU Evropského parlamentu a Rady EU ze dne 8. června 2011, která se týká omezení použití určitých nebezpečných látek v elektrických a elektronických zařízeních.
(CZ) Na naši vlastní zodpovědnost prohlašujeme, že je tento výrobek v souladu s následujícími standardy a normami: Je v súlade s normou 2011/65/EÚ Európskeho parlamentu a Rady z 8. júna 2011 týkajúcej sa obmedzenia používania určitých nebezpečných látok v elektrickom a elektronickom vybavení.

(SK) Výhlasujeme na našu výhradnú zodpovednosť, že tento výrobok je v zhode a súlade s nasledujúcími normami a predpismi: Je v súlade s normou 2011/65/EÚ Európske ho parlamentu a Rady z 8. júna 2011 týkajúcej sa obmedzenia používania určitých nebezpečných látok v elektrickom a elektronickom vybavení.
(SL) S polno odgovornostjo izjavljamo, da je ta izdelek v skladu in da odgovarja naslednjim standardom terpredpisom: je v skladu z direktivo 2011/65/EU Evropskega parlamenta in Sveta z dne 8. junij 2011 o omejevanju uporabe določenih nevarnih snovi v električni in elektronski opremi.
(PL) Deklarujemy na własną odpowiedzialność, że ten produkt spełnia wymogi zawarte w następujących normach i przepisach: jest zgodny z Dyrektywą 2001/65/UE Parlamentu Europejskiego i Rady z dnia 8 czerwca 2011 r. w sprawie ograniczenia stosowania niektórych niebezpiecznych substancji w sprzęcie elektrycznym i elektronicznym.
(LT) Prisiimdami visą atsakomybę deklaruojame, kad śis gaminys atitinka żemiau paminėtus standartus arba nuostatus: atitinka 2011 m. birželio 8 d. Europos Parlamento ir Tarybos direktyvą 2011/65/EB dėl tam tikrų pavojingų medžiagų naudojimo elektros ir elektroninėje jrangoje apribojimo.
(LV) Ir atbilstoša Eiropas Parlamenta un Padomes 2011. gada 8. jūnija Direktīvai 2011/65/ES par dažu bīstamu vielu izmantošanas ierobežošanu elektriskās un elektroniskās iekārtās.
(ET) Apgalvojam ar visu atbildību, ka šis produkts ir saskaņā un atbilst sekojošiem standartiem un nolikumiem: ir atbilstoša Eiropas Parlamenta un Padomes 2011. gada 8. jūnija Direktīvai 2011/65/ES par dažu bīstamu vielu izmantošanas ierobežošanu elektriskās un elektroniskās iekārtās.
(RO) Declarăm prin aceasta cu răspunderea deplină că produsul acesta este în conformitate cu următoarele standarde sau directive: este în conformitate cu Directiva 2011/65/UE a Parlamentului European și a Consiliului din 8 iunie 2011 cu privire la interzicerea utilizării anumitor substanțe periculoase la echipamentele electrice și electronice.
(HR) Izjavljujemo pod vlastitom odgovornol, šu da je strojem ukladan sa slijedešim standardima ili standardiziranim dokumentima i u skladu sa odredbama: usklađeno s Direktivom 2011/65/EU europskog parlamenta i viječa izdanom 8. lipnja 2011. o ograničenju korištenja određenih opasnih tvari u električnoj i elektroničkoj opremi.
(SRL) Pod punom odgovornošću izjavljujemo da je usaglašen sa sledećim standardima ili normama: usaglašen sa direktivom 2011/65/EU Evropskog parlamenta i Saveta od 8.juna.2011. godine za restrikciju upotrebe određenih opasnih materija u električnoj i elektronskoj opremi.
(RU) Под свою ответственность заявляем, что данное изделие соответствует следующим стандартам и нормам: соответствует требованиям Директивы 2011/65/EU Европейского парпамента и совета от 8 июня 2011 г. по ограничению использования определенных опасных веществ в электрическом и электронном оборудовании
(UK) На свою власну відповідальність заявляємо, що дане обладнання відповідає наступним стандартам і нормативам: задовольняє вимоги Директиви 2011/65/ЄС Європейського Парламенту та Ради від 8 червня 2011 року на обмеження використання деяких небезпечних речовин в електричному та електронному обладнанні.
(EL) Δηλώνουμε υπεύθυνα ότι το προϊόν αυτό συμφωνεί και τηρεί τους παρακάτω κανονισμούς και πρότιπα: συμμοφρώνεται με την Οδηγία 2011/65/ΕΕ του Ευριπαϊκού Κοινοβουλίου και του Συμβουλίου της 8ης Ιουνίου 2011 για τον πειρορισμό της χρήσης ορισμένων επικύδυνων υσιών σε ηλεκτρικό και ηλεκτρονικό εξοπλισμό.
(AR) تيكلاتىشاميچوكتاو روياعىلە عم قغابوئي جىتنىلىا الله نأ اندج وانستكيلوىسەر ظىڭن ئىذىن
(TR) Tek sorumlusu biz olarak bu ürünün aşağıdaki standart ve yönergelere uygun olduğunu beyan ederiz.

EN60335-1, EN60335-2-45, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3, EN62233

2006/42/EC, 2006/95/EC, 2004/108/EC, 2002/95/EC, 2011/65/EU, 2012/19/EU

Zwolle, 01-03-2015

H.G.FRosberg

CEO FERM B.V.

FERM B.V. - Lingenstraat 6 - 8028 PM - Zwolle - The Netherlands