QFC90350 - Range hood Husqvarna-Electrolux - Free user manual and instructions

Product Type	Range Hood
Brand	Husqvarna-Electrolux
Model	QFC90350
Power Supply	220-240 V, 50 Hz
Suction Versions	External evacuation or internal recirculation
Control Panel	Push buttons with speed selection (1-3), intensive speed, light switch
Display	LED display showing speed and filter saturation indicators
Maximum Extraction Power	Not specified, typical for this class ~600-800 m³/h
Intensive Speed	Yes, runs for 5 minutes then returns to previous speed
Lighting Type	Halogen, 12 V, 20 W max, G4 base
Grease Filter	Washable metal, clean monthly (hand or dishwasher)
Charcoal Filter Type	Optional: Washable Type 150 LONG LIFE or non-washable Type 60/80
Charcoal Filter Maintenance	Washable: wash every 2 months, replace mattress every 3 years; Non-washable: replace every 4 months
Filter Saturation Indicator	Yes, can be enabled/disabled for charcoal filter
Installation Min Distance (Electric Hob)	50 cm
Installation Min Distance (Gas Hob)	65 cm (or as per hob instructions if greater)
Safety Features	Disconnect power before maintenance; use gloves; never use without grating
Energy Class	Not specified, typical A+
Noise Level	Not specified
Spare Parts Availability	Original spare parts via www.husqvarna-electrolux.se/shop
Warranty	Not specified, standard 2 years
Environmental Compliance	Recyclable packaging; do not dispose with household waste

Frequently Asked Questions - QFC90350 Husqvarna-Electrolux

How do I install the range hood?

Follow the installation manual. The minimum distance from the hob surface is 50 cm for electric cookers and 65 cm for gas or mixed cookers. Ensure the mains power is disconnected until installation is complete.

How do I clean the grease filter?

Remove the grease filter and clean it monthly with a neutral detergent. It can be washed by hand or in a dishwasher at a low temperature and short cycle.

How do I replace the charcoal filter?

Depending on the type: For washable Type 150 LONG LIFE, wash every 2 months and replace the mattress every 3 years. For non-washable Type 60/80, replace the cartridge every 4 months.

What do the flashing LED indicators mean?

The 1st speed LED + F flashes when the grease filter needs cleaning. The 2nd speed LED + F flashes when the charcoal filter needs cleaning or replacement.

How do I reset the filter saturation indicator?

After cleaning or replacing the filters, press button 1 for 3 seconds until the flashing LED stops. The F LED will also turn off.

What light bulb does the hood use?

It uses a 12 V, 20 W max halogen bulb with a G4 base, suitable for open luminaires. Do not touch the new bulb with bare hands.

Can I use the hood in recirculation mode?

Yes, the hood can be used with internal recirculation by installing a charcoal filter. You must enable the charcoal filter saturation indicator via the control panel.

How do I enable the charcoal filter saturation indicator?

With the hood off, press buttons 2 and 4 simultaneously for 3 seconds. The LED F will light up and the 1st speed LED will flash, followed by a beep.

What should I do if the controls don't work?

Disconnect the hood from the power supply for at least 5 seconds, then reconnect. Wait 15 seconds before checking if it operates correctly.

Where can I buy spare parts?

Original spare parts are available at www.husqvarna-electrolux.se/shop. You can also find accessories and consumables there.

USER MANUAL QFC90350 Husqvarna-Electrolux

Modern kitchen interior with stainless steel appliances and large windows in the background (no visible text or symbols)

BÄSTA KUND FÖR PERFEKT RESULTAT

Illustration of a hand using a tool to cut or adjust a mechanical component (no text or symbols visible)

4.2 Kolfilter - Type 150 LONG LIFE - Aktivt kolfi Iter som kan rengöras

Illustration of a hand holding a small circular object, a tool, and a compass-like dial (no text or symbols)

KJÆRE KUNDE

FOR PERFEKTE RESULTATER

Illustration of a hand using a tool to cut or adjust a mechanical component (no text or symbols visible)

4.2 Type 150 LONG LIFE - Vaskbart aktivt kullfi Iter

5 ON/OFF-knapp for belysning.

Dersom ventilatoren eller kommandoknappene ikke skulle virke, anbefaler vi å koble fra strømforsyningen i minst 5 sekunder og deretter slå på ventilatoren igjen. Vent så i 15 sekunder og kontroller om ventilatoren fungerer korrekt.

Anordning for kontroll av fettfi Iteret og kullfi Iteret

Illustration of a hand holding a screwdriver, a magnifying glass with arrows indicating rotation, and a small circular object (no text or symbols)

ARVOISA ASIAKKAAMME TÄYDELLISTEN TULOSTEN SAAVUTTAMISEKSI

Illustration of a hand using a tool to cut or adjust a mechanical component (no text or symbols visible)

Illustration of a hand holding a screwdriver, with a magnifying glass inspecting the interior (no text or symbols)

KÆRE KUNDE

FOR PERFEKTE RESULTATER

Illustration of a hand using a tool to cut or adjust a mechanical component (no text or symbols visible)

Illustration of a hand holding a small object, a screwdriver, and a circular compass with arrows indicating rotation (no text or symbols)

DEAR CUSTOMER

Thank you for choosing this Husqvarna-Electrolux product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it.

Visit our website to:

Get usage advice, brochures, trouble shooter, service information: www.husqvarna-electrolux.se

Register your product for better service: www.husqvarna-electrolux.se

Buy Accessories, Consumables and Original spare parts for your appliance: www.husqvarna-electrolux.se/shop

ENVIRONMENT CONCERNS

Recycle the materials with the symbol ☐ Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of

electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.

CUSTOMER CARE AND SERVICE

We recommend the use of original spare parts.

When contacting Service, ensure that you have the following data available.

The information can be found on the rating plate. Model, PNC, Serial Number.

Warning / Caution-Safety information.

General information and tips

Environmental information.

Subject to change without notice.

1. ⚠️ SAFETY INSTRUCTIONS

Caution! Closely follow the instructions set out in this manual. All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined. The extractor hood has been designed exclusively for domestic use.

Warning! Do not connect the appliance to the mains until the installation is fully complete.

Before any cleaning or maintenance operation, disconnect hood from the mains by removing the plug or disconnecting the mains electrical supply.

Always wear work gloves for all installation and maintenance operations.

The appliance is not intended for use by children or persons with impaired physical, sensorial or mental faculties, or if lacking in experience or knowledge, unless they are under supervision or have been trained in the use of the appliance by a person responsible for their safety.

This appliance is designed to be operated by adults, children should be monitored to ensure that they do not play with the appliance. This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the appliance.

Never use the hood without effectively mounted grating!

The hood must NEVER be used as a support surface unless specifically indicated.

The premises where the appliance is installed must be sufficiently ventilated, when the kitchen hood is used together with other gas combustion devices or other fuels. The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose such as discharging exhaust fumes from appliances burning gas or other fuels.

The flaming of foods beneath the hood itself is severely prohibited.

The use of exposed flames is detrimental to the filters and may cause a fire risk, and must therefore be avoided in all circumstances.

Any frying must be done with care in order to make sure that the oil does not overheat and ignite.

Caution! Accessible parts of the hood may become hot when used with cooking appliance.

With regards to the technical and safety measures to be adopted for fume discharging it is important to closely follow the regulations provided by the local authorities. The hood must be regularly cleaned on both the inside and outside (AT LEAST ONCE A MONTH).

This must be completed in accordance with the maintenance instructions provided in this manual). Failure to follow the instructions provided in this user guide regarding the cleaning of the hood and filters will lead to the risk of fi res.

Do not use or leave the hood without the lamp correctly mounted due to the possible risk of electric shocks.

We will not accept any responsibility for any faults, damage or fi res caused to the appliance as a result of the non-observance of the instructions included in this manual.

2. USE

The hood serves to aspirate the fumes and vapors resulting from cooking.

The attached installation manual indicates the version to be used depending on the model you have, the suction version with

external evacuation

or fi ltering with

internal recirculation

3. INSTALLATION

The mains power supply must correspond to the rating indicated on the plate situated inside the hood. If provided with a plug connect the hood to a socket in compliance with current regulations and positioned in an accessible area, after installation. If it not fitted with a plug (direct mains connection) or if the plug is not located in an accessible area, after installation, apply a double pole switch in accordance with standards which assures the complete disconnection of the mains under conditions relating to over-current category III, in accordance with installation instructions.

Warning! Before re-connecting the hood circuit to the mains supply and checking the efficient function, always check that the mains cable is correctly assembled.

The hood is provided with a special power cable; if the cable is damaged, request a new one from Technical Service. The minimum distance between the supporting surface for the cooking equipment on the hob and the lowest part of the range hood must be not less than 50cm from electric cookers and 65cm from gas or mixed cookers. If the instructions for installation for the gas hob specify a greater distance, this must be adhered to.

4. MAINTENANCE

ATTENTION! Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket. The cooker hood should be cleaned regularly (at least with the same frequency with which you carry out maintenance of the fat filters) internally and externally. Clean using the cloth dampened with neutral liquid detergent. Do not use abrasive products.

Warning! Failure to carry out the basic cleaning recommendations of the cooker hood and replacement of the fi Iters may cause fi re risks. Therefore, we recommend observing these instructions.

The manufacturer declines all responsibility for any damage to the motor or any fi re damage linked to inappropriate maintenance or failure to observe the above safety recommendations.

4.1 Grease filter - The grease filter must be cleaned once a month using non aggressive detergents, either by hand or in the dishwasher, which must be set to a low temperature and a short cycle. When washed in a dishwasher, the grease fi lter may discolour slightly, but this does not affect its fi ltering capacity.

Illustration of a hand using a tool to adjust or install a mechanical component (no text or symbols visible)

4.2 Charcoal filter - Type 150 LONG LIFE - Washable activated charcoal fi Iter

The charcoal fi liter can be washed once every two months using hot water and a suitable detergent, or in a dishwasher at 65^ C (if the dishwasher is used, select the full cycle function and leave dishes out). Eliminate excess water without damaging the fi liter, then remove the mattress located inside the plastic frame and put it in the oven for 10 minutes at 100^ C to dry completely. Replace the mattress every 3 years and when the cloth is damaged.

4.3 Type 60/80 - NON-washable activated charcoal fi Iter

The saturation of the charcoal filter occurs after more or less prolonged use, depending on the type of cooking and the regularity of cleaning of the grease filter.

In any case it is necessary to replace the cartridge at least every four mounths.

The charcoal filter may NOT be washed or regenerated.

5. CONTROLS

The hood is fitted with a control panel with aspiration speed selection control and a light switch to control cooking area lights. Use the high suction speed in cases of concentrated kitchen vapours. It is recommended that the cooker hood suction is switched on for 5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes approximately after terminating cooking.

1 OFF - ON push button

Press once or more to obtain the function desired:

ON: the hood switches on to the last speed selected.

OFF: all the functions are switched off except the illumination.

2 Speed selection push button (extraction power).

Press this push button once or more to select the most suitable extraction speed (power) (1-2-3).

3 The display shows the extraction power selected, signalling the saturation of the filters F.

4 Intensive speed on/off. The Intensive speed runs for 5 minutes:

If the hood is on when the Intensive speed is activated, the hood reverts to previous speed after 5 minutes.

If the hood is off when the Intensive speed is activated, the hood will be turned off after 5 minutes.

To interrupt the Intensive speed, press button 1 or 2.

5 Light ON/OFF

Should the hood or the controls fail to operate: disconnect the power supply for at least 5 seconds, then turn the hood back on again.

Grease and charcoal fi Iter maintenance indicator

This hood is fitted with a device that indicates when it is necessary to clean the grease filter or the charcoal filter (if the hood is used in the recirculation version with a charcoal filter).

On delivery, the hood is not supplied with a charcoal filter, so the saturation indicator will be disabled.

If the hood is to be used with a charcoal fi lter, the saturation

indicator light must be enabled as follows: Set the hood in "OFF".

Pressing keys 2 and 4 simultaneously for three seconds, LED F lights up and begins to flash the 1st speed led. After 1 second the 2nd speed led also flashes and the system emits a sound signal (-Beep-) to indicate setting taking place.

To remove the charcoal fi lter signal press push buttons 2 and 4 simultaneously for 3 seconds. LED F lights up and begins to flash the 1st speed led (grease filter) and the 2nd speed led. After 1 second, only the 1st speed led continues to fl ash. The system emits a sound signal (-Beep-) to indicate setting taking place.

Grease fi Iter LED

The 1st speed led (+ led F) fl ashes, when it is time to clean the grease fi iter.

Always comply with the maintenance instructions for the grease fi iter.

Charcoal fi Iter LED

The 2nd speed led (+ led F) fl ashes, when the charcoal fi iter needs to be cleaned or replaced.

Resetting the saturation indicator

After cleaning or replacing the fil ters, press button 1 for 3 seconds until the 1st speed led or the second speed led stops fl ashing. The F LED also turns off.

6. LIGHTING

Disconnect the hood from the electricity. Warning! Prior to touching the light bulbs ensure they are cooled down. Replace with a new 12 Volt, 20 Watt (Maximum) halogen light made for a G-4 base SUITABLE FOR USE IN OPEN LUMINAIRES. Follow package directions and do not touch new light with bare hands.

Illustration of a hand holding a small circular component, with a magnifying glass and directional arrows indicating motion (no text or symbols)

www.husqvarna-electrolux.se/shop

CE