DJC-119A-SZ20-144 - Drill Cotech - Free user manual and instructions

Product Type	Cordless Drill/Driver
Brand	Cotech
Model	DJC-119A-SZ20-144
Voltage	14.4 V
Battery Type	Lithium-ion (Li-ion)
Battery Capacity	1.3 Ah
No-load Speed (Low)	0–400 rpm
No-load Speed (High)	0–1100 rpm
Max Torque	18 Nm
Torque Settings	19 + drill mode
Chuck Type	Keyless chuck
Chuck Capacity	10 mm
Charger Input	230 V, 50 Hz
Charger Output	14.4 V DC, 1.5 A
Charging Time	1 hour
Noise Level (LpA)	68 dB(A) (K=3 dB)
Noise Level (LwA)	79 dB(A)
Vibration Level	2.75 m/s² (K=1.5 m/s²)
Forward/Reverse	Yes, with selector
Variable Speed Trigger	Yes
Work Light	Yes (automatically on when trigger pressed)
Battery Charge Indicator	3-LED charge level display
High/Low Speed Switch	Yes (2 positions)

Frequently Asked Questions - DJC-119A-SZ20-144 Cotech

How do I change the drill bit?

This drill has a keyless chuck. Simply twist the chuck to the left to tighten and to the right to loosen. Ensure the bit sits securely centered in the middle of the chuck.

How should I charge the battery for the first time?

Charge the battery fully before first use. For initial charge, charge for 1 hour. For maximum battery performance, allow the battery to discharge completely during the first 5–6 uses, then charge for 1 hour each time.

How do I adjust the torque setting?

Rotate the torque setting ring (located behind the chuck) to your desired number (1–19) or to the drill symbol. Higher numbers provide higher torque. Start at the lowest setting and increase as needed.

How do I select between low and high speed?

Use the high/low speed switch on top of the drill. Position 1 gives 0–400 rpm (low speed, high torque). Position 2 gives 0–1100 rpm (high speed, low torque). Only switch when the drill is stopped.

What type of battery does this drill use?

The drill uses a 14.4 V Li-ion battery with 1.3 Ah capacity. Only use batteries and chargers approved by the manufacturer.

How do I use the forward/reverse selector?

The forward/reverse selector is located above the trigger. Slide it to the left for forward (drilling/screwing) and to the right for reverse (removing screws). Ensure the chuck is completely motionless before changing direction.

How do I clean and maintain the drill?

Keep the motor ventilation openings free of dust. Clean the housing with a damp cloth and mild soap. Do not use strong detergents. For long-term storage, fully charge the battery.

What does the work light and battery indicator show?

Pressing the trigger activates the work light and the 3-LED battery indicator. Three lights = fully charged; two lights = medium; one red light = low battery, needs charging.

What should I do if the drill does not start?

Check that the battery is inserted and charged. Ensure the forward/reverse selector is fully engaged in either direction. If the problem persists, consult a qualified technician. Do not attempt to open the drill.

How do I dispose of the drill and battery?

Follow local regulations for disposal of electronic waste and Li-ion batteries. Do not dispose of batteries in household waste. Contact your local authority for recycling options.

USER MANUAL DJC-119A-SZ20-144 Cotech

Read the entire instruction manual carefully and make sure that you fully understand it before you use the equipment. Keep the manual for future reference.

Viktig information:

Line drawing of a handheld electric drill with labeled components and wiring (no text or symbols on the device itself)

ART.NO

18-3187

40-7974

MODEL

DJC-119A-SZ20-144-UK

DJC-119A-SZ20-144

Ver. 20140520

Original instructions

Bruksanvisning i original

Please read the entire instruction manual before use and save it for future reference. We reserve the right for any errors in text or images and for making any necessary technical changes to this document. If you should have any questions concerning technical problems please contact our Customer Services.

Safety

General safety instructions for cordless power tools

Warning! Read all the instructions. Failure to adhere to the following instructions may lead to electric shocks, fires and/or serious injury. The term “power tools” in the warning text below refers to your handheld mains operated or battery operated tool. SAVE THESE INSTRUCTIONS.

1) The work area

a) Keep the work area clean and well illuminated. Cluttered and poorly lit areas invite accidents.
b) Do not use power tools in explosive environments, e.g. near flammable liquids, gases or dust. Power tools generate sparks that can easily ignite dust or fumes.
c) Keep children and other bystanders away from the area where you are using the power tool. Distractions can cause you to lose your concentration and control.

2) Electrical safety

a) The power tool's plug must fit correctly into the wall socket. Never modify the plug in any way. Never use an adaptor together with earthed power tools. Unmodified plugs and suitable wall sockets decrease the risk of electric shock.
b) Avoid physical contact with earthed objects, such as pipes, radiators, ovens or refrigerators. There is an increased risk of receiving an electrical shock if your body is earthed.
c) Do not expose the power tool to rain or other wet conditions. If water gets inside a power tool it increases the risk of electric shock.
d) Do not abuse the lead. Never use the lead to carry the tool or pull the plug from the wall socket. Keep the lead away from heat, oil, sharp edges and movable parts. Damaged or tangled leads increase the risk of electric shock.
e) When using power tools outdoors, use an extension lead that is suitable for this purpose. Use of an extension lead designed for outdoor use decreases the risk for electric shock.
f) If for some reason you must use a power tool in a wet environment, always connect it to the mains via an earth-fault circuit breaker such as an RCD (residual current device). Using an RCD significantly reduces the chances of you receiving an electric shock.

3) Personal safety

a) Pay attention to your actions and use common sense when using power tools. Never use power tools if you are tired or under the influence of drugs, alcohol or medication. One moment of inattention while using a power tool may result in serious injury.
b) Use protective equipment. Always wear safety glasses. Using protective clothing such as dust masks, non-slip safety shoes, helmets and ear defenders when needed decreases the risk of injury.
c) Avoid accidental starts. Make sure that the power switch is set to OFF before plugging the tool into a wall socket. Never carry a power tool with your finger on the trigger and never connect the power tool to a wall socket when the switch is set to ON, since it may result in injury.
d) Remove all service tools/keys before switching on the power tool. A service tool left on a moving part of the power tool may result in injury.
e) Do not overreach. Make sure you stand steady and well balanced at all times. This will allow you to have more control in unexpected situations.

f) Wear suitable clothing. Do not wear loose-fitting clothing or jewellery. Keep hair, clothes and gloves away from moving parts. Loose-fitting clothes, jewellery or long hair could become caught in moving parts.

g) If equipment for dust extraction or collection is available, make sure that it is connected and used properly. Using technical aids may decrease dust related hazards.

4) Use and maintenance of power tools

a) Do not force the power tool. Use a power tool suitable for the work you are about to perform. The proper power tool will perform the task better and safer if used at the correct feed rate.
b) Never use the power tool if the power switch does not switch the tool on and off properly. All power tools that cannot be controlled by the power switch are dangerous and must be repaired.
c) Unplug the lead from the wall socket before making any adjustments, changing accessories or storing the power tool. These precautions reduce the risk of the power tool starting unexpectedly.
d) Store any power tools that are not being used out of children's reach. Do not allow people who are unfamiliar with the tool or its functions to operate the tool. Power tools can be dangerous if they fall into the hands of inexperienced users.
e) Maintaining power tools. Check for any incorrect settings, parts that catch, broken parts or anything else which may cause the power tool to malfunction. If something is damaged it must be repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep tools sharp and clean. Properly maintained cutting tools with sharp blades are less likely to jam and are easier to control.
g) Use the power tool, accessories and similar according to the instructions and in an appropriate way suitable for the type of power tool used. Also take into consideration your work environment and the type of work to be done. Using the power tool for a purpose other than that for which it is intended could result in a dangerous situation.

5) Use and service of cordless power tools

a) Make sure that the power switch is set to OFF before attaching the battery. Attaching a battery to a power tool when the power switch set to ON is inviting an accident.
b) Only charge the battery using a charger approved by the manufacturer. A charger suitable for one type of battery can constitute a fire hazard if used for another type of battery.
c) Only use the rechargeable power tool with batteries intended for that purpose. The use of other types of batteries might cause damage or fire.
d) When not in use, the battery should be stored away from other metal objects such as paper clips, coins, keys, nails, screws or any small objects that could bridge the gap between the battery terminals. Short circuiting the battery terminals can cause burns or fires.
e) If the battery is mistreated, it may leak acid; avoid contact with this acid. If you accidentally come into contact with the acid, rinse your skin with water. If the acid comes into contact with your eyes, consult a doctor. Battery acid can cause irritation and burns.

6) Service

a) Repairs and service should only be performed by qualified tradesmen, and only with original spare parts. This guarantees that the safety of the power tool is maintained.

General safety instructions for batteries and chargers

1. Never attempt to dismantle a battery.
2. Never store a battery in direct sunlight or at temperatures above 40^ C.
3. Only charge the battery when the ambient temperature is between +5 °C and 40 °C.
4. Never expose the battery or charger to water.

Product safety symbols

Read the entire instruction manual.

Always use ear protection.

Always use safety glasses.

For indoor use only.

Product description

1. Keyless chuck
2. Torque setting ring
3. High/Low speed switch
4. Bubble vial (spirit level)
5. Forward/reverse selector
6. Battery
7. Battery release button
8. Work light and battery charge indicator
9. Power trigger (variable speed)

Charging

The battery needs to be charged fully before initial use.

Charge the battery for 1 hour the first time it is charged.

For maximum battery performance: Allow the battery to discharge completely the first 5 or 6 times it is used, charge it for 1 hour on each occasion.

1. Remove the battery from the drill by pressing the battery release button (7) and pulling out the battery.
2. Connect the charger to a wall socket. The green LED will then come on.
3. Insert the battery into the charger. The green LED will turn off and the red LED will light during charging.
4. When the battery is fully charged the red LED will turn off and the green LED will light.
5. Unplug the charger from the wall socket and remove the battery from the charger when the charging process is complete.

Constant green light Charger connected to mains/Charging complete.

Constant red light Charging in progress.

Flashing red and green Defect.

• Charging time is about 1 hour for normal use.
• The battery can become warm during charging. This is completely normal.
• The battery and charger work best at normal room temperature. Do not charge in direct sunlight or colder temperatures. The temperature range for charging is 5–40 °C.
• For long-term storage the battery should be fully charged.

Setup

Forward/reverse

Select forward or reverse using the selector (5). If the selector is not pushed in all the way the drill will not start. The chuck must be completely motionless before changing directions.

Torque

The machine has an adjustable clutch for setting the desired torque using the setting ring (2). If set correctly, the clutch will disengage the drive at the preset torque setting. This prevents screws from being driven in too far and prevents damage to the machine. The setting selection should be based on the type and size of screw and the material being screwed into. Always start at the lowest setting and increase in increments if unsure.

Changing drill or screwdriver bits

This tool has a keyless chuck which enables drill bits or screwdriver bits to be changed with one hand. Twist the chuck to the left to tighten, to the right to untighten.

Ensure that the bit sits securely centred in the middle of the chuck.

Operation

The machine is started and stopped by holding or releasing the power trigger (9). The drill/driver is equipped with a variable speed control, which makes it extremely practical for driving screws. The more the power trigger is pressed, the greater the speed of the chuck. After working extensively at low speeds, the motor should be run at no-load maximum speed for about 3 minutes to cool down the motor.

For drilling, set the torque setting ring (2) to drill mode ⏻ (drill bit symbol on ring).

High/Low speed switch

There are two settings: Position 1: 0–400 rpm, position 2: 0–1100 rpm.

Work light and battery indicator

The work light will come on when the power trigger is depressed. The 3 battery charge indicators will also come on. When the battery is fully charged, all 3 light up. When only the red lights up, the battery needs charging.

Drilling tips and advice

• When drilling into slippery materials, like tiles, you should place a strong piece of tape on the area in which you wish to drill to prevent the bit from wandering.
• When drilling into metal you should first use a centre punch to make a small indentation at the spot where you wish to drill. This indentation will help hold the bit in place and prevents it from wandering when you drill.
• When drilling into metal you should also use cutting oil to assist in drilling and to preserve the machine and drill bit.
  • Always use a clamp or vice to hold the workpiece.
• When drilling into walls, make sure not to damage water pipes, electricity cables or gas pipes.

Care and cleaning

• Always keep the motor's ventilation openings free from dust and debris.
• Clean the machine regularly using a moist cloth and washing up liquid. Avoid using strong detergents.
• For long-term storage the battery should be fully charged.

Disposal

Follow local ordinances when disposing of this product. If you are unsure of how to dispose of this product, please contact your local authority.

Symbol of a trash bin crossed out by two crossed lines, with no text or labels present.

Specifications

Variable speed control 0–400/0–1100 rpm

Operating voltage 14.4 V

Preset torque settings 19 + drill, max. 18 Nm

Keyless chuck Diam 10 mm

Noise level LpA: 68 dB(A)

(Uncertainty K:3 dB) LwA: 79 dB(A)

Vibration value 2.75 m/s ^4 (Uncertainty K:1.5 m/s ^4 )

Battery type Li-ion

Voltage 14.4 V

Battery Capacity 1.3 Ah

Charger

Input power 230 V, 50 Hz

Output power 14.4 V DC, 1.5 A

Charging time 1 hour

Borrmaskin 14,4 V LI-ION

ART.NR 18-3187 MODELL DJC-119A-SZ20-144-UK 40-7974 DJC-119A-SZ20-144

Symbol of a trash bin crossed with no text or labels, accompanied by a solid black rectangle below (no readable text or symbols)

Specifikationer

Symbol of a trash bin crossed with no text or labels, accompanied by a solid black rectangle below (no readable text or symbols)

Porakone 14,4 V LI-ION

TUOTENRO 18-3187 MALLI DJC-119A-SZ20-144-UK 40-7974 DJC-119A-SZ20-144

Symbol of a trash bin crossed with a diagonal line and a horizontal bar below (no text or labels)

Tekniset tiedot

Symbol of a trash bin with crossed lines and a solid rectangle below (no text or labels)

Technische Daten

Declaration of Conformity

Declares that this product complies with the requirements of the following directives and standards

Machinery directive 2006/42/EC

EN 60745-1:2009

EN 60745-2-1:2010

EN 60745-2-2:2010

EMC directive 2004/108/EC

EN 55014-1:2006

EN 55014-2:1997

+A1:2001+A2:2008

Klas Balkow

President

Insjön, Sweden, 2011-09-29

SVERIGE

KUNDTJÄNST Tel: [phone]

Fax: [phone]

E-post: [e-mail]

INTERNET www.clasohlson.se

BREV Clas Ohlson AB, 793 85 INSJÖN

NORGE

KUNDESENTER Tlf.: 23 21 40 00

Faks: 23 21 40 80

E-post: [e-mail]

INTERNETT www.clasohlson.no

POST Clas Ohlson AS, Postboks 485 Sentrum, 0105 OSLO

SUOMI

ASIAKASPALVELU Puh.: 020 111 2222

Postal 10 – 13 Market Place

Kingston Upon Thames

Surrey

KT1 1JZ

DEUTSCHLAND