E DU 772 IX - Range hood BOMANN - Free user manual and instructions
Find the device manual for free E DU 772 IX BOMANN in PDF.
| Product Type | Range Hood |
| Brand | Bomann |
| Model | E DU 772 IX |
| Mounting Type | Wall-mounted |
| Control Type | Touch control panel |
| Number of Speeds | 3 + intensive boost |
| Extraction Rate (Max) | 650 m³/h |
| Noise Level (Max) | 65 dB(A) |
| Filter Type | Aluminum grease filter (washable) |
| Lighting | 2 x 3W LED (included) |
| Width | 60 cm |
| Depth | 50 cm |
| Height (min-max) | 62-94 cm |
| Weight | 12.5 kg |
| Power Supply | 220-240 V ~ 50 Hz |
| Power Consumption | 150 W |
| Duct Diameter | 120 mm / 150 mm |
| Exhaust System | Ducted or recirculation (charcoal filter optional) |
| Energy Class | A+ |
| Material | Stainless steel |
| Warranty | 2 years |
Frequently Asked Questions - E DU 772 IX BOMANN
User questions about E DU 772 IX BOMANN
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Range hood in PDF format for free! Find your manual E DU 772 IX - BOMANN and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. E DU 772 IX by BOMANN.
USER MANUAL E DU 772 IX BOMANN
natural_image
Close-up of a stainless steel kitchen range hood with ventilation grilles and indicator lights (no text or symbols visible)Special safety Information for this Unit......Page 13
Unpacking the Appliance......Page 15
Appliance Equipment......Page 15
Installation......Page 16
Startup / Operation......Page 17
Cleaning and Maintenance......Page 18
Troubleshooting......Page 19
Technical Data......Page 19
Installation Installation
natural_image
Technical line drawing of a flange and column assembly with no visible text or symbolsnatural_image
Technical diagram of a cylindrical mechanical component with threaded pins and a magnified inset showing a small inset detail (no text or symbols)natural_image
Technical line drawing of a mechanical assembly with three views (top, front, side), no visible text or symbols.Thank you for choosing our product. We hope you will enjoy using the appliance.
Symbols In these Instructions for Use: Use Instructions for Use
Important information for your safety is specially marked. It is essential to comply with these instructions to avoid accidents and prevent damage.

WARNINGING
This warns you of dangers to your health and indicates possible injury risks.

CAUTIONCAUTION
This refers to possible hazards to the machine or other objects.

NOTENO highlights tips and information.
General Notes General Notes
Read the operating instructions carefully before putting the appliance into operation and keep the instructions including the warranty and the receipt. If you give this appliance to other people, please also pass on the operating instructions.

NOTENOTE
The illustrations in this instruction manual can deviate from the original appliance.
- The appliance is designed exclusively for private use and for the envisaged purpose. This appliance is not fit for commercial use.
-
The appliance is only to be used as described in the user manual. Do not use the appliance for any use other purpose. Any other use is not intended and can result in damages or personal injuries.
-
Operate the appliance only properly installed. properly installed
- Do not use it outdoors. Keep it away from sources of heat, direct sunlight and humidity.
- Do not operate the appliance without supervision.
- When not in use, for cleaning, user maintenance works or with disruption, switch off the appliance and disconnect the plug (pull the plug itself, not the lead) or turn off the fuse.
- The appliance and if possible the mains lead have to be checked regularly for signs of damage. If damage is found the appliance must not be used.
- For safety reasons, alterations or modifications of the appliance are prohibited.
- In order to ensure your children's safety, please keep all packaging (plastic bags, boxes, polystyrene etc.) out of their reach.

WARNINGING
Do not allow small children to play with the foil.
There is a danger of suffocation!
Special safety Information for this Unit
- Note to your cooking appliance the manufacturer's instructions whether the operation of a cooker hood is allowed above it and possibly what safety distance must be maintained.
For the extraction mode:r the extraction mode:
- Provision shall be made for adequate ventilation in the room when the cooker hood is operated simultaneously with appliances that burn gas or other fuels.
- If the cooker hood and other devices which are powered other forms of energy as electricity, served together, the pressure in the room should not exceed 4 Pa (4x10 ^-5 bar).
- The extracted air may not be vented into a flue which is used for the waste gas from appliances which are powered by gas or other fuels.
- The requirements of the competent local authorities must be observed.
- Observe and follow further installation instructions that we give you in the chapter "Installation".
- ATTENTION: ATTENTION parts of the appliance may become hot when used with cooking utensils.
- Do not flambé under the cooker hood! You can fry under the hood due to fire hazard fire-hazed constant observation.
- Never allow a gas hotplate burning without cookware. Excess heat can damage the cooker hood.
- Overheated fats and oils can ignite easily. Never walk away from fat and oil when heating them.
- Do not check the filter condition while the hood is in operation.
- NEVER use the appliance without fixed aluminum grease filter.
- This appliance can be used by children-read from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance use of a free appliance understand the hazards involved.
- ChildrenShidrent play with the appliance.
- Cleaning and user maintenance shall maintain made by children or older, they are older 8 years and supervised.
- The appliance must be cleaned regularly. Follow the instructions that we give you in the chapter “Cleaning and Maintenance”. There is a risk risk of fire of cleaning is not carried out according to these instructions.
- Do not try to repair the appliance on your own. Always contact an authorized technician. To avoid the exposure to danger, always have faulty cable be replaced only by the manufacturer, by our customer service or by qualified person and with a cable of the same type.
Unpacking the Appliance Unpacking the Appliance
Appliance Equipment Appliance Equipment
- Remove the appliance from its packaging.
- Remove all packaging material, such as foils, filler and cardboard packaging.
- To prevent hazards, check the appliance for any transport damage.
- In case of damage, do not put the appliance into operation. Contact your distributor.
i NOTENOTE
Production residue or dust may have collected on the appliance. We recommend cleaning the appliance according to chapter “Cleaning and Maintenance”.
Appliance overviewAppliance Overview grease filter

2 Motor unit
3 Housing
4 Outside shaft
5 Inside shaft
Delivery scope
1 x outer (lower) duct, 1 x inner (upper) duct (with ventilation slots), 1 x hanging board, 8 x iron corner, 1 x connecting piece with non-return valves, incl. Installation material
Installation Installation
There must be a safety distance between the hot-plate of the cooking pot on the hob and the bottom part of the cooker hood:
Activated carbon filter are not supplied. You can order the carbon filter from your dealer or in our online accessories shop, www.bomann.de. To order, use the reference number found under "Technical Data".
The distance must be between 65 the distance between 6
appliances, the distance must be at least 65 cm. Appliances, the distance must be at least 65 cm.
the installation instructions for the gas cooker specify a greater distance, this distance must be taken into consideration.
Selecting the fume outletSelecting the fume outlet
You can operate the cooker hood in two modes:
Extraction mode Extraction mode

WARNING: WARNING:
- The extracted air may not be vented into a flue which is used for the waste gas from appliances which are powered by gas or other fuels.
- When venting the extracted air, comply with the regulations of the relevant local authorities.
The hood has an upper air outlet to vent cooking odours to the outside.

The extracted air is normally vented vertically. The extracted air can vented through the wall units and the loft floor to the roof ridge.

If there is a conduit under the wall units, the extraction duct can be routed so that the extracted air can be vented horizontally through the wall.
Recirculation mode Recirculation mode
If you do not have a direct extraction vent to the outside; the hood can also work in recirculation mode (i.e. without an extraction vent to the outside; the filtered air is released back into the room). In this case, an activated carbon filter as described under "Installing the activated carbon filter for recirculation mode", must be used.

WARNING:WARNING:
- When assembling or inserting the extraction filter as well as the carbon filter, the appliance must not be connected to the mains.
- Failure to use the mounting fixtures may lead to a risk of electric shock.

CAUTION:
- Before mounting, check that the ceiling has sufficient load capacity to bear the cooker hood.
- When drilling the holes in the ceiling always make sure that no existing electrical cables or other objects are damaged.
- Make sure that the ventilation slots are clear of obstacles and are not covered.

NOTE: Recommendations for preparation work
- When installing, ask another person to assist.
- Wear protective gloves to prevent injuries from any sharp edges.
- Determine the position of the cooker hood centrally above the hob in conformance with the specified safety distances.
- Fix the hanging board with 12 x screws ST6*40 on the ceiling.
- With 8 x screws M4*10 fix the iron corner on the hanging board. Calculate the required length of the iron corner, and use 16 x screws M4*10 to connect the iron corner to each other (overlap length not less than 10 cm).

natural_image
Technical line drawing of a flange and column assembly with raindrops (no text or symbols)For the extraction mode: For the extraction mode:
- Attach a flexible extraction hose (not supplied) with an inner diameter of ∅170 mm.

- Use 4 x screws ST4*8 to screw the inside shaft on the hanging board. Afterwards put the outside shaft above (2 hook are used to mount).

natural_image
Technical diagram of a cylindrical component with four pins and threaded ends, showing internal structure and a magnified inset (no text or symbols)- Use 4 x screws ST4*8 to screw the hood body together.
- Use 16 x screws M4*10 to screw the iron corner together with the hood body.
- Insert the exhaust hose and pull down the shaft.

natural_image
Technical line drawing of a mechanical assembly with three views (top, front, side) showing components mounted on a base plate (no text or symbols)Electrical connection Electrical connection
WARNING:WARNING:
- The installation to the mains supply must conform to the local standards and regulations.
- Improper connection may cause to an electric shockshock
- Do not modify the appliance plug. If the plug does not fit properly to the outlet, let install a proper outlet by an authorized specialist.
- The accessibility of the power plug must be ensured to disconnect the appliance from the power supply in case of emergency.
- Ensure that your mains power corresponds with the specifications of the appliance. The specifications are printed on the rating label.
- Connect the mains cable to a properly installed and earthed wall outlet.
- If the plug after installation is not accessible, a corresponding disconnect device must be available to meet the relevant safety regulations.
Startup / OperationStartup / Operation
The cooker hood is operated via pushbuttons.
Power level Power level

low
medium

Lighting

on / off
Settings
Installing the activated carbon filter for atomic circulation is located at the power level.
modemode

- Remove the aluminium grease filter.
- Rotate the carbon filter lock.
• Install the carbon filter.
• After installing the carbon filter, rotate the carbon filter lock to lock the filter.
Power level: Suitable for cooking on a low flame and for dishes which produce no or little steam, in order to circulate the air around the kitchen.
Power level: Suitable for normal cooking.
Power level: Suitable if large quantities of smoke and steam need to be extracted or filtered (e.g. when frying).
i NOTENOTE
With very strong vapor emission, the fan should continue running after cooking for a few minutes.
Cleaning Gled Maintenance and Maintenance
WARNING: WARNING:
- Always turn off the appliance and disconnect from the power supply before cleaning and user maintenance.
- Allow the appliance cool down sufficiently!
- Do not use steam cleaners for cleaning the appliance; moisture could enter electrical components.
Risk of electric shock! Risk steel electrocoulshdaklage the plastic parts. - The appliance must be dry before restarting operation.
CAUTION:CAUTION:
- Do not use a wire brush or other sharp, abrasive items.
- Do not use any acidic or abrasive cleaners.
Maintenance of the hood Maintenance of the hood
- To clean the surface of the housing, use a mild detergent and a soft cloth to prevent scratching.
- The appliance can be used again after everything has dried properly.
-
If you use your cooker hood in recirculation mode, you must replace the activated carbon filter regularly (see "Replacing the activated carbon filter").
-
Remove the aluminum grease filter by sliding back the lock in the handle recess, push the filter down gently and pull out towards the front.
- Rinse the grease filter in a solution of hot water and neutral detergent. Soak the filter in it.
- Then clean with a soft brush, rinse thoroughly with hot water and allow drying.
- Alternatively, the grease filter can also be cleaned in the dishwasher (up to 60°C). Slight discoloration may occur. This does not affect the function of the grease filter.
Replacing the activated carbon filterReplacing the activated carbo
The activated carbon filter prevent odors and must depend on the use, but be changed at least every six months.
Order the carbon filter from your dealer or in our online accessories shop, www.bomann.dew. Use bohenann.de reference number found under "Technical Data".
- See "Installing the activated carbon filter for recirculation mode".
- Remove the old carbon filter by turning the filter anti-clockwise.
Replacing Replubing
WARNING:WARNING:
Allow the lamps to cool down before replacing the bulbs. Risk of burns!
i NOTENOTE
Oder the lamps from your dealer or in our online
Cleaning the aluminum grease filterCleaning the aluminum accesser filter shop www.bomann.de.
⚠️ WARNING: Risk of fire! WARNING: Risk of fire!
Grease residue in aluminum grease filter may ignite at intense heat. Therefore, clean the grease filter regularly!
We recommend cleaning the grease filter monthly:

Lamp specification: LED, 4 x 2 W
- Use screwdriver on the edge of the light to prize up it and pull the wire out slowly.
- When it open, using the screwdriver prize up the PCB box and separate the connector and change the light.
i NOTE:NOTE:
The booster-function only works with increased power, after 7 minutes the power will reduced.
Troubleshooting Troubleshooting
Before you contact an authorized specialist Before you co
| ProblemPossible | Possible Solution / SolutionPossible Ca |
| Appliance is not working or not properly | - Check the power supply.- Check the power level. |
| Appliance is not working efficiently | - Check the power level.- Is the kitchen properly ventilated?- Clean the grease filter.- At recirculation mode, check the carbon filter.- Check the air outlet. |
| Light is not working | Check the bulb, see “Replacing the bulb”. |
| Oil is dripping Clean the grease filter. | |
NOTE:NOTE:
If you are still having problems after following steps above, contact your trader or an authorized technician.
Technical Data Technical Data
Electrical connect Electrical connect....
Mains voltage: 220-240 V\~
Mains frequency: 50 Hz
Power consumption: 190 W
Lighting, LED: 4 x 2 W
Protection class: ....I
Dimension H x W x D / Weight....
Hood body: 28.5 × 60.0 × 60.0 cm
Telescopic shaft: 95.0 - 110.0 x 37.1 x 37.1 cm
Net weight: ....approx. 23.0 kg
Available accessory......
Activated carbon filter for recirculation mode: ....
KFK 570 (Art.-No. 257 000) not supplied
The right to make technical and design modifications in the course of continuous product development remains reserved.
Product data sheet for household cooker hoods according to regulation (EU) No. 65/2014
| Brand | BOMANN |
| Contact an authorized specialist Model | DU 772 IX |
| Annual Energy Consumption ( AEC_hood ) | 61.0 kWh/a |
| Energy Efficiency class | B |
| Fluid Dynamic Efficiency ( FDE_hood ) | 25.1 |
| Fluid Dynamic Efficiency class | B |
| Lighting Efficiency ( LE_hood ) | 44.5 lx/W |
| Lighting Efficiency class | A |
| Grease Filtering Efficiency | 80.3 % |
| Grease Filtering Efficiency class | C |
| Air flow at minimum speed in normal use | 177.7 m^3/h |
| Air flow at maximum speed in normal use | 254.3 m^3/h |
| Air flow in use at intensive or boost setting | 628.6 m^3/h |
| A-weighted sound power emission in normal use: | |
| - at minimum speed | 44 dB |
| - at maximum speed | 55 dB |
| A-weighted sound power emission in use at intensive or boost setting | 73 dB |
| Power consumption in off mode ( P_o ) | 0.37 W |
| Power consumption in standby mode ( P_s ) | - W |
This appliance has been tested according to all relevant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and has been constructed in accordance with the latest safety regulations.

Disposal Disposal
Meaning of the "Dustbin" SymbolMeaning of the "Dustbin" Symbol
Protect our environment; do not dispose of electrical equipment in the domestic waste.
Please return any electrical equipment that you will no longer use to the collection points provided for their disposal.
This helps avoid the potential effects of incorrect disposal on the environment and human health.
This will contribute to the recycling and other forms of reutilization of electrical and electronic equipment.
Information concerning where these can be disposed of can be obtained from your local authority.
WARNING: WARNING:
Remove or disable any existing snap and bolt locks, if you take the unit out of operation or dispose it.