IAN 354287 - Uncategorized Livarno Lux - Free user manual and instructions

Product Type	LED Wall & Ceiling Lamp
Model Numbers	14144406L, 14144408L, 14144506L
Operating Voltage	230-240 V ~ 50 Hz
Rated Power	18 W (LED)
Protection Class	I
IP Rating	IP20
LED Module	Permanent, non-replaceable
Suitable Locations	Indoor, dry, enclosed spaces only
Mounting	Wall or ceiling
Scope of Delivery	1 lamp, 3 wall plugs, 3 screws, 2 protective tubes, 1 set of instructions
Required Tools (not included)	Pencil, 2-pole circuit tester, screwdriver, electric drill, drill bit 6 mm, side cutting pliers, ladder
Installation	Professional electrical installation recommended
Safety	Electric shock warning; disconnect power before cleaning; do not immerse in water
Cleaning	Use dry lint-free cloth only; allow lamp to cool completely
Warranty	36 months from date of purchase
Disposal	Environmentally friendly; do not dispose with household waste
Certifications	EU directives, Declaration of Conformity
Dimmability	Not suitable for external dimmers or electronic switches

Frequently Asked Questions - IAN 354287 Livarno Lux

How do I install the Livarno Lux LED wall/ceiling lamp?

Installation must be performed by a qualified electrician. First, disconnect power by removing the fuse or switching off the circuit breaker. Follow the steps in the manual: remove the lampshade, mark drill holes, drill holes (6 mm, depth 40 mm), insert wall plugs, secure the light base, connect the mains cable to the lustre terminal (live L, neutral N, ground green-yellow), replace the protective cover, and reattach the lampshade.

What tools are needed for installation?

Required tools (not included): pencil, 2-pole circuit tester, screwdriver, electric drill with 6 mm drill bit, side cutting pliers, and a ladder.

Can I replace the LED bulb in this lamp?

No, the LED module is permanent and non-replaceable. If the LED reaches the end of its life, the entire lamp must be replaced.

Is the lamp dimmable?

No, this lamp is not suitable for external dimmers or electronic switches. Using a dimmer may cause damage or malfunction.

Can I use this lamp outdoors or in wet areas?

No, the lamp is rated IP20 and is only suitable for indoor use in dry, enclosed spaces. Do not expose it to moisture or water.

How should I clean the lamp?

Always disconnect power before cleaning. Allow the lamp to cool completely. Use only a dry, lint-free cloth. Do not use water, solvents, or abrasive cleaners.

What does the warranty cover?

The warranty covers material and manufacturing defects for 36 months from the date of purchase. It does not cover wear parts (e.g., bulbs) or damage from improper use, non-observance of instructions, or unauthorized interference. Proof of purchase is required.

How do I dispose of the lamp?

Do not dispose of the lamp with household waste. Take it to a local recycling facility for environmentally friendly disposal. The packaging is made from recyclable materials.

Is the lamp safe for use around children?

Yes, but supervision is advised. Children aged 8 years and older may use the lamp if supervised or instructed. Keep packaging away from toddlers to avoid suffocation risk. The lamp should be installed out of reach of children to prevent burns from hot surfaces.

What is the voltage and power rating of the lamp?

The lamp operates at 230-240 V ~ 50 Hz and has a rated power of 18 W (LED). Protection class I, IP20.

USER MANUAL IAN 354287 Livarno Lux

LÁMPARA LED DE PARED Y TECHO / LAMPADA LED DA SOFFITTO O DA PARETE

ES

LÁMPARA LED DE PARED Y TECHO

Assembly, operating and safety instructions

ES

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the device.

DE AT CH

GB / MT Assembly, operating and safety instructions Page 29

Intended use......Page 30

Scope of delivery....Page 31

Parts description......Page 31

Technical data......Page 31

Safety Page 31

Safety notices Page 31

Preparation......Page 32

Required tools and material Page 32

Prior to installation Page 32

Initial use Page 32

Installing the light Page 32

Maintenance and cleaning......Page 33

Disposal Page 34

Warranty and service......Page 34

Warranty Page 34

Service address....Page 34

Declaration of conformity....Page 34

Manufacturer......Page 34

List of pictograms used
	Read the instructions!		Electric shock warning!Danger to life!
	This light is suitable only for interior use, in dry and enclosed spaces.		This light is not suitable for external dimmers or electronic switches.
	Alternating current (type of current and voltage)		For your safety
	Volt		Caution! Risk of burns due to hot surfaces!
	Hertz (mains frequency) Lifespan
	Watt (effective power)	[IMAGE]	Dispose of packaging and device in an environmentally-friendly manner!
	Protective conductor		The packaging is made from 100 % recycled paper.
	Observe the warning and safety instructions!		Danger to life and risk of accident for infants and children!
	Switching cycles		Colour rendering index
	This light is only suitable for indoor use in dry and enclosed spaces.		Lumens
			Light temperature in Kelvin

LED Wall & Ceiling Lamp

Introduction

Congratulations on your new product.

You have selected a high quality product.

Please be sure to carefully read the com-

plete operating instructions. Fold out the page with the illustrations. These instructions are part of the product and contain important information on setup and handling. Always follow all safety instructions. Before using this product for the first time verify the correct voltage and that all parts are properly installed. Should you have any questions or you are unsure about operating the product, please contact

the dealer or service centre. Please keep these instructions in a safe place and pass them on third parties as applicable.

Intended use

This light is only suitable for indoor use in dry and enclosed spaces. The light can be fastened to any normally inflam-

mable surface. This product is intended for private household use only. This product is intended for normal operation and can be used for wall or ceiling installation.

Scope of delivery

Check immediately after unpacking that the parts are complete and that the product is in proper condition.

1 LED wall and ceiling light, model 14144406L/14144408L/14144506L
3 Wall plugs
3 Screws
2 Protective tubes
1 Set of assembly instructions and instructions for use

- Parts description

1 Lever (14144406L/14144408L)
2 Lampshade
3 Light base
4 Mains connection cable (external)
5 Lustre terminal protective cover
6 Wall plug
7 Screws
8 Lustre terminal
9 Protective tube

- Technical data

Light:

Modelno.:14144406L/14144408L/14144506L

Operating voltage: 230-240V\~50Hz

Rated power: LED 18 W

Protection class: 1/⊥

IP rating: IP20

LED:

LED light bulb: LED module (permanent)

Rated power: 1 x max. 18 W

Safety

Safety notices

Damage due to failure to comply with these operating instructions will invalidate the guarantee! We assume no liability for consequential damage! We assume no liability for material damage or personal injury due to improper handling or failure to comply with the safety instructions!

WARNING! RISK OF FATAL INJURY AND ACCIDENT HAZ-ARD FOR TODDLERS AND

SMALL CHILDREN!

Never leave children unsupervised with the packaging materials. The packaging material poses a suffocation hazard. Children frequently underestimate the dangers. Please always keep the product out of the reach of children.

This device may be used by children aged 8 years and up, as well as by persons with reduced physical, sensory or mental capacities, or lacking experience and / or knowledge, so long as they are supervised or instructed in the safe use of the device and understand the associated risks. Do not allow children to play with the device. Cleaning and user maintenance must not be performed by children without supervision.

Avoid the risk of fatal injury from electric shock

• Ensure that a qualified electrician, or a person trained to carry out electrical installations, performs the electrical installation.
  ■ Always check the light, power supply, and mains cable for damage before plugging it in. Never use the light if it shows any signs of damage.

WARNING!

A damaged mains cable indicates a life-threatening danger due to electric shock. In the event of damage, repairs or other problems with the light please contact the service centre or a qualified electrician.

Prior to installation, remove the fuse or switch off the circuit breaker (0 setting) in the fuse box.
Prior to installation verify the mains voltage on site corresponds with the operating voltage required for the light (see "Technical data").
■ Ensure that the light does not come into contact with water or other liquids under any circumstances.
■ Never open any of the components of the elec- conditions.

trical equipment or insert any objects into the same components. This will pose a risk of fatal injury from electric shock.

Do not install the light on a wet or conductive substrate!

Prevent fire and injury hazards

RISK OF INJURY!

Check each light bulb and the lampshade for damage immediately after unpacking.

Do not assemble the light if the light bulbs and / or lampshade are defective. In this case, contact the service centre for a replacement.
Do not look directly into the light source (light bulb, LED etc.).
Do not use optical instruments to look at the light source (e.g. magnifying glass).
This lights's illuminant is not replaceable; if the illuminant has reached the end of its service life, the whole light must be replaced.
This light is not suitable for external dimmers or electronic switches.

Safe working

Mount the light so that it is protected from moisture and dirt.
Carefully prepare for assembly and allow yourself adequate time. Organise all parts and any necessary additional tools or materials before starting so they are easy to reach.
Always be attentive! Always pay attention to what you are doing and use common sense. Never install the light if you are having difficulty concentrating or do not feel well.

● Preparation

• Required tools and material

The tools and materials specified are not included.

This information and these values are non-binding and are only provided as a reference. The nature of the material is determined by the individual local

• Pencil/making tool
• 2-pole circuit tester
• Screwdriver
• Electric drill
• Bit (approx. ∅ 6 mm)
• Side cutting pliers
• Ladder

- Prior to installation

Important: The electrical connection must be established by a qualified electrician or a person trained to perform electrical installations. This person must be familiar with the properties of the light and the connection regulations.

Familiarise yourself with all the instructions and diagrams in this manual, as well as with the light itself, before you install it.
Before installation ensure that the circuit, to which the light will be connected, is not energised. To do so, remove the fuse or switch off the circuit breaker in the fuse box (0 position).
☐ Use a 2-pole voltage tester to verify cables are not live.

- Initial use

- Installing the light

Model 14144406L/14144408L:

Before installing the light, remove the fuse or switch off the circuit breaker (0 setting) in the fuse box.

☐ Remove the lampshade 2 from the light base 3 by turning the three levers 1 on the side of the light outwards (see Fig. A and B).
☐ Mark the drill holes using the holes in the light base 3 intended for the screws 7 as a guide (see Fig. C).
☐ Now drill the mounting holes (approx. ∅ 6 mm, depth approx. 40 mm). Make sure that you do not damage the power cable (see Fig. D).
☐ Insert the wall plugs 6 into the drilled holes.
☐ Secure the light base 3 using the included screws 7 (see Fig. E). Feed the mains connection cable (external) 4 through the cable guide.
☐ Remove the protective cover 5 from the lustre terminal 8 by loosening the screw (see Fig. F).
☐ Pull the protective tubes 9 over cables L and N of the mains connection cable (external) 4 (see Fig. G).
☐ Connect the mains connection cable (external) 4 with the light using the lustre terminal 8.

Note: Make sure that you correctly connect each individual wire of the mains connection cable (external) 4: live wire, black or brown = symbol L, neutral wire, blue = symbol N. Connect the protective conductor ⊥ (green-yellow) with the earth terminal which is marked in the light base 3.

☐ Screw the protective cover 5 of the lustre terminal 8 tightly into place again (see Fig. G).
Place the lampshade 2 back onto the light base 3 and close the three levers 1 (see Fig. H).

Ensure that it is securely tightened.

☐ Reinsert the fuse or switch the circuit breaker back on (see Fig. 1).

Your light is now ready to use.

Model 4144506L:

Before installing the light, remove the fuse or switch off the circuit breaker (0 setting) in the fuse box.
☐ Remove the lampshade 2 from the light base 3 by carefully turning it anticlockwise (see Fig. A and B).

☐ Mark the drill holes using the holes in the light base 3 intended for the screws 7 as a guide (see Fig. C).
☐ Now drill the mounting holes (approx. ∅ 6 mm, depth approx. 40 mm). Make sure that you do not damage the power cable (see Fig. D).
☐ Insert the wall plugs 6 into the drilled holes.
☐ Secure the light base 3 using the included screws 7 (see Fig. E). Feed the mains connection cable (external) 4 through the cable guide.
☐ Remove the protective cover 5 from the lustre terminal 8 by loosening the screw (see Fig. F).
☐ Pull the protective tubes 9 over cables L and N of the mains connection cable (external) 4 (see Fig. G).
☐ Connect the mains connection cable (external) 4 with the light using the lustre terminal 8.

Note: Make sure that you correctly connect each individual wire of the mains connection cable (external) 4: live wire, black or brown = symbol L, neutral wire, blue = symbol N. Connect the protective conductor ⊥ (green-yellow) with the earth terminal which is marked in the light base 3.

☐ Screw the protective cover 5 of the lustre terminal 8 tightly into place again (see Fig. G).
☐ Secure the lampshade 2, by screwing it clockwise onto the light base 3 (see Fig. H).
☐ Reinsert the fuse or switch the circuit breaker back on (see Fig. I).

Your light is now ready to use.

● Maintenance and cleaning

WARNING! RISK OF ELECTRIC SHOCK!

Disconnect the light from the mains circuit before cleaning. To do so, remove the fuse or switch off the circuit breaker in the fuse box (0 position).

WARNING! RISK OF ELECTRIC SHOCK!

For electrical safety, never clean the light with water or other liquids, or immerse it in water.

⚠️ CAUTION! DANGER OF BURNS DUE TO HOT SURFACES!

Allow the light to cool completely.

Do not use solvents, benzene or similar substances. They could damage the light.
☐ Only use a dry, lint-free cloth for cleaning.
Replace the fuse or switch on the circuit breaker (I setting) inside the fuse box.

- Disposal

The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities.

Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with following meaning: 1-7: plastics / 20-22: paper and fibre-board/80-98: composite materials.

To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority.

- Warranty and service

Warranty

You receive a 36 month warranty on this product, valid from the date of purchase. The appliance has been carefully produced under strict quality control. Within the warranty period we shall rectify without charge all material and manufacturing defects. In the event of a defect during the warranty period, please send the appliance to the listed Service Centre address, referencing the following model number: 14144406L/14144408L/14144506L.

Wear parts (such as bulbs) and damage caused by improper handling, non-observance of the operating instructions or unauthorised interference are excluded from the warranty. The performance of services under the warranty does not extend or renew the warranty period.

Serviceaddress

Please have your receipt and the article number (e. g. IAN 123456_7890) ready as your proof of purchase when enquiring about your product.

Declaration of conformity

This product fulfils the requirements of the applicable European and national directives. Conformity has been demonstrated. The relevant declarations and documents are held by the manufacturer.

Manufacturer