IAN 71088 - Sink MIOMARE - Free user manual and instructions

USER MANUAL IAN 71088 MIOMARE

Assembly, operating and safety instructions

PL

ARMATURA DO WANNY

GB Assembly, operating and safety instructions Page 3

This product is suitable for all pressure-tight hot water systems such as central heating boilers, instantaneous water heaters, pressurised boilers and the like. It is not suitable for low-pressure water heaters such as wood or coal burning bath geysers, oil or gas bath geysers, open electrically heated water tanks. If in doubt please seek the advice of a plumber or heating engineer. Any use other than that described here or modification to the product is not permitted and may lead to damage to persons or property. There is also the risk of injury and loss of life. The product is intended for personal use only and not for medical or commercial use. The manufacturer accepts no liability for loss or damage arising from improper use.

● Description of parts

1 2 S-connectors
2 2 Rosettes
3 2 Sealing rings
4 1 Tap body
4a 1 Changeover button
4b 1 Threaded connector (for the shower hose)
4c 2 Nuts (for S-connectors)
5 1 Mixer nozzle
6 1 Control lever
7 1 Locking screw
8 | 1 Hot/cold label
9 1 Cartridge end ring
10 1 Cartridge locking ring
11 1 Cartridge
12 1 Setting screw
13 1 Setting ring

- Technical data

Connection spacing: 135/165 mm

Connections (Shower hose): G ^1/2 "

(approx. 21 mm)

Water connection nut:

approx. 30 mm

Hot water temperature:

Max.: 85°C

Operating pressure:

Max.: 3 bar

Min.: 0.5 bar

Safety advice

WARNING! RISK OF LOSS OF LIFE OR ACCIDENT TO INFANTS AND CHILDREN! Never

leave children unsupervised with the packaging materials. Danger of suffocation. Keep the product away from children. The product is not a toy.

CAUTION - RISK OF ELECTRIC

SHOCK! Leaks or the escape of water can lead to danger to life from

electric shock. Check all connections for leaks carefully. In addition, ensure that all cables from electrical devices are correctly and safely installed.

CAUTION! RISK OF INJURY! Please ensure that no parts are damaged and that all parts are correctly assembled. Incorrect assembly could lead to injury.

Please note that seals are wear parts and therefore will require to be replaced from time to time. Damaged parts could adversely affect safety and proper function.

CAUTION! RISK OF DAMAGE TO

PROPERTY! Have the installation done by experienced persons only. Leaks or escape of water can lead to serious damage to buildings or household fittings and furniture. Check all connections for leaks carefully.

Ensure that all seals are correctly seated to prevent leakage of water.

CAUTION! DANGER OF SCALDING!

When making the hot water setting please ensure that the temperature of the water is not too high.

Before installation, make yourself familiar with all the existing services, e.g. water connection and stopcocks.

Please read carefully through these operating instructions before installing and using the product.

Keep all the safety advice and instructions in a safe place for future reference!

- Installation

- Installing the tap

Note: To protect the parts from scratches while being screwed together cover them with a damp cloth or use plastic clamps.

■ Before you start installation turn off the main water supply to prevent serious leakage of water.
☐ Install the tap at the wall connection as shown in Figure A.

Connecting the accessories (shower head and shower hose)\*:

Note: So that the parts do not get scratched while being screwed together, protect them with a damp cloth or use plastic clamps.

☐ Screw an ordinary shower hose* firmly on to the thread 4b.
☐ Attach an ordinary shower head* to the shower hose*.
□ Observe the installation instructions for the accessories.

* (not included)

- Flushing the tap

☐ The tap must be flushed through before first use to remove any dirt. To do this, follow these steps (see Fig. B):
☐ Screw the mixer nozzle 5 off.
Before using the tap for the first time, open the main water supply. and allow the water to run for two minutes so that any residues are dissolved away.
☐ Then screw the mixer nozzle on again.

Operation

- Bringing into use

Note: If the tap has not been used for a long period flush the pipes through thoroughly in order to avoid stagnation and build-up of residues in the drinking water supply.

Open the main water supply.
☐ Lift the control lever 6 and swivel it to the right or left to regulate the strength or temperature of the water flow.

Hot water:

□ Swivel the control lever to the left.

Cold water:

□ Swivel the control lever to the right.

☐ Check that the mixer tap is working properly. To do this, swivel the lever into all the possible positions. Please check the connections regularly for leaks.

- Changeover knob water inlet bath/shower head

Filling the bath:

☐ Press down the changeover button 4a. The water flows through the mixer nozzle 5.

Showering:

☐ Lift up the changeover button. The water flows through the shower hose and the connected shower head.

Note: If you turn off the water flow using the control lever 6 then the fitting automatically switches to bath filling. If you pull the changeover button and turn in clockwise direction, the shower mode can be locked at all time (see fig. F).

- Eco-function / saving water

The tap has a water-saving function. This feature limits the rate of water flow through the tap. The flow can be infinitely regulated between 0–100 % by means of a stop.

☐ Turn off the main water supply.
☐ Remove the red/blue hot/cold label 8 carefully by a small flat screwdriver (see Fig. C).
☐ Release the lock screw 7 by turning it anti-clockwise using a hexagon socket screw key.

CAUTION! Do not take the screw completely out; just loosen it until the control lever can be easily taken off.

☐ Take off the control lever.
☐ Loosen the cartridge end ring 9 by hand, then screw off the cartridge locking ring 10 by using a pipe wrench.

Note: The setting screw for regulating the water flow is in the lever arm, which projects from the cartridge (see Fig. D).

☐ To reduce the flow, turn the setting screw anti-clockwise. This limits the movement of the lever arm and therefore the movement of the control lever as well. The flow is reduced as the control lever now cannot be lifted quite so high.

Note: The more you turn the screw anticlockwise, the more the flow is reduced.

☐ Tighten the cartridge locking ring 10 onto the lever arm again by using a pipe wrench, then tighten the cartridge end ring 9 by hand.
☐ Place the control lever back on to the lever arm and tighten the locking screw by turning it clockwise using a hexagon socket screw key.
☐ Press the red/blue hot/cold label 8 into the opening.
☐ Turn on the main water supply and check the water-saving function.

- Setting the temperature limiter

The cartridge 11 in this unit has a temperature limiter. This function is not activated in the factory (neutral setting).

CAUTION! Change the temperature limiter setting only after the tap has been installed.

☐ Turn off the main water supply.
☐ Remove the control lever 6 as described in the section on "Eco-function / saving water".
☐ Now pull the setting ring 13 upwards with the help of a screwdriver.

Note: Do not remove the cartridge.

☐ Place the setting ring in the desired position as shown in Fig. E.

Place the control lever back on to the tap. To do this, follow the procedure described in the section on "Eco-function / saving water".

☐ Turn on the main water supply and check the temperature limiter.

● Maintenance and cleaning

Tap care and cleaning

Please note that sanitary fittings require special care and attention. Therefore you should follow the following advice:

■ Never use corrosive or alcohol-based materials for cleaning, as these could damage the product.
□ Clean your fittings with clean water, mild detergent and a soft cloth or leather only.
☐ Screw out the mixer nozzle at regular intervals and remove lime deposits or foreign bodies.

Non-observance of the above care advice can be expected to result in damage to the surface of the fittings. In this event your rights under the warranty may be invalidated.

- Disposal

The packaging is wholly composed of environmentally friendly materials that can be disposed of at a local recycling centre.

Contact your local refuse disposal authority for more details of how to dispose of your worn-out product.

Information

- Potability of mains water

☐ Find out about the potability of your mains water supply. Your local water authority or water supply company will be able to inform you.

The following general recommendations apply to the potability of the water from your pipework:

• Let the water run freely for a short time if it has been stagnating in the pipework for more than four hours. Do not use any of this stagnant water in the preparation of food or for drinking. This applies particularly as far as babies and infants are concerned. Failure to observe this advice may result in risks to health. Fresh water can be readily distinguished from stagnant as fresh water is noticeably cooler.
  Do not use stagnant water from chromium-plated pipework for the preparation of food or for drinking or for personal hygiene if you are allergic to nickel. This water may contain high quantities of nickel and trigger an allergic reaction.
• Do not use water from lead pipework for preparing food or drink for babies or infants. Do not use it for preparing food or drink during pregnancy. Lead dissolves in drinking water and is particularly damaging to the health of babies and young children.

Armatura do wanny

Temperatura tople vode:

Maks.: 85 °C

Delovni tlak:

Maks.: 3 bar

Min.: 0,5 bar

Varnostna navodila

OPOZORILO! ŽIVLJENJ- SKA NEVARNOST IN NEVAR- NOST NESREČ ZA MALČKE IN

Anschlüsse (Brauseschlauch): G ^1/2 " (ca. 21 mm)

c/o Milomex Services

Hilltop Cottage

Barton Road

Pulloxhill

Bedfordshire

MK45 5HP

UK

Model-No.: Z31166B

Version: 03/2012

© by ORFGEN Marketing

Simple equilateral triangle outline with no text or symbols