C98 - Bicycles Vevor - Free user manual and instructions

Product Type	Balance Bike for Children
Brand	Vevor
Model	C98
Recommended Age	3-6 years
Maximum User Weight	25 kg
Bike Weight	3 kg
Wheel Size	12 inches
Frame Material	Steel
Adjustable Seat Height	Yes, with safety marking
Adjustable Handlebar Height	Yes, with safety marking
Brakes	None (balance bike)
Safety	Helmet required, adult supervision
Usage	Flat surface, not on roads
Assembly Required	Yes (fork, handlebar, seat)
Tools Included	Hex key
Maintenance	Lubricate bearings every 6 months, clean with wax
Spare Parts Available	Fork, handlebar, seat, bearings
Warranty	Electronic warranty certificate
Manual Contents	Instructions in French and other languages

Frequently Asked Questions - C98 Vevor

How to assemble the Vevor C98 balance bike?

Follow the steps: install the front fork with the washers, then the handlebar by tightening the screw with a torque of 18 N.m, finally the seat with a torque of 12 N.m. Respect the height safety markings.

What is the recommended age for this bike?

The bike is recommended for children aged 3 to 6 years.

Is a helmet required to use this bike?

Yes, wearing a helmet is mandatory for the child's safety.

How to maintain the bike?

After two weeks, readjust the axles. Lubricate rotating parts with grease every six months. Clean the paint with a dry cloth and use wax if necessary.

Can I use this bike on the road?

No, it is a children's toy, to be used only on flat surfaces and under adult supervision.

How to adjust the handlebar height?

Loosen the vertical screw with the hex tool, adjust the height (do not exceed the safety marking), then tighten to 18 N.m.

What if the seat is loose?

Loosen the hex screw on the seat clamp, adjust the height, then tighten to 12 N.m.

How to lubricate the bearings?

Disassemble the bearings, clean them, apply grease, then reassemble.

What are the risks if parts are damaged?

Stop use immediately and replace defective parts with original parts.

Where to find spare parts?

Contact technical support via www.vevor.com/support.

USER MANUAL C98 Vevor

Technical Support and E-Warranty Certificate www.vevor.com/support

Kids’ Balance Bike

MODEL: C98

We continue to be committed to providing you with tools at competitive prices. "Save Half", "Half Price", or any other similar expressions used by us only reflect an estimate of savings you might benefit from buying certain tools with us compared to top brands, and do not necessarily mean that all categories of tools offered will actually save you half compared to the top major brands. Please verify carefully when placing an order.

MODEL: C98

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you of any technology or software updates on our product.

INSTRUCTIONS

Thank you very much for choosing this Kids' Balance Bike. Please read all of the instructions before using it. The information will help you achieve the best possible results.

WARNING:

Please read this manual carefully before using the product. Failure to do so may result in serious injury. For safe driving of your baby, the following warnings must be noted:

1. Assembly and adjustment of the product must be carried out by an adult. Please keep children away from moving parts. This product contains small parts. If swallowed, they will pose a choking hazard. Keep these small parts away from children when assembling!
2. Children should ride under adult supervision.
3. This bike is a children's toy and shall not be used as a means of transportation on highways and streets.
4. Children must wear safety helmets when riding.
5. Do not ride on bumpy terrain.
6. Before each use, the balance car should be inspected to ensure it is in good condition.
7. Use as intended only. Do not stand on the product.
8. Inspect before every use. Do not use it if parts are loose or damaged.
9. If any parts are missing, broken, damaged, or worn, stop using the product until repairs are made and factory replacement parts are installed. Age of application: 3-6 years old.

Installation and use

1. Install the front fork

① Remove the front fork lock, gasket, upper stop, and ball carrier. ② Keep the front wheel pattern consistent with the rear wheel, and put the front riser into the head tube of the frame, then install the carrier (exposing the steel ball side down), the upper stop, and tighten. Then install the gasket in turn, and lock the front nut and tighten.

2. Install handlebars

1. Remove the vertical cover, use the hex tool to loosen the lifting screw. 2. Insert the riser into the front fork riser, adjust the handlebar direction so that the handlebar is perpendicular to the direction of the bicycle, and adjust the height of the handlebar to suit the height of the rider (note: the maximum height of the handlebar cannot exceed the safety mark). Tighten the lifting screw (tightening torque is not less than 18 N·m). Finally, snap into the handlebar stand cover.

3. Install the saddle

① Loosen the saddle chuck hex socket screw with a wrench. ② Insert the saddle tube into the frame riser, adjust the saddle to the rider's height (note: the maximum height of the saddle is subject to the safety mark on the saddle tube), and then lock the saddle chuck hex (locking torque is not less than 12 N·m).

Maintenance and repair

1. When a new car is used for about two weeks, it is necessary to rotate the front axle, rear axle, and wheels to maintain normal operation.
2. The rotating parts of the balance car should be constantly lubricated with butter to extend the service life. Disassemble and wash the whole car every six months, and fill the rotating parts with butter.
3. Paint: The surface should not be wrapped in plastic bags or cloth, and should not be wiped with a wet cloth, to avoid loss of gloss, bubbles, peeling, or luster decline. You can choose high-quality car wax to wipe, increasing brightness.
4. Electroplated parts: If a yellowish-brown network is found on the surface, you can use neutral oil or sewing machine oil to wipe frequently to prevent the network from expanding.
5. The front bowl is loose: first loosen the front and lock the mother, remove the gasket, and then adjust the gap between the upper bowl and the steel ball with a wrench, then install the gasket and tighten and lock the mother.
6. If the front axle is loose or too tight, it will affect the operation. When adjusting, first loosen the nut on one side of the front axle, then adjust the tight nut with a wrench, and support the wheel in the front middle, and finally tighten the nut.

VEVOR®

TOUGH TOOLS, HALF PRICE

Technical Support and E-Warranty Certificate

www.vevor.com/support

VEVOR

TOUGH TOOLS, HALF PRICE

Technical Support and E-Warranty Certificate www.vevor.com/support

www.vevor.com/support

VEVOR

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

VEVOR

TOUGH TOOLS, HALF PRICE

Technical support and e-warranty certificate www.vevor.com/support

NEED HELP? CONTACT US!

www.vevor.com/support