MD 15486 - Coffee machine MEDION - Free user manual and instructions

USER MANUAL MD 15486 MEDION

Coffee machine with grinder

Modern coffee maker with digital display and control buttons (no visible text or symbols)

Labeled diagram of a coffee maker with numbered parts for identification

QR code image containing encoded data, no visible human-readable text

1. About these instructions.... 20

1.1. Symbols and keywords used in these instructions ....20

EN

1. Package contents

2. Proper use 21

3. Safety instructions ....NL

4.1. Keep electrical equipment out of reach of children .....22

4.2. Setting up....22

DK

4.3. Mains connection....23

4.4. Faults 23

4.5. Handling the device safely 23

4.6. Cleaning the device 25

1. Overview of the device.... 26

2. Operating panel

3. Initial operation and use 27

7.1. Setting the time....28

7.2. Preparing the coffee machine for the brewing process .....28

7.3. Using the timer....31

7.4. End of the brewing process/automatic switch-off ....31

7.5. Cleaning and descaling 32

1. Disposal 3:

2. Technical data

3. Legal notice 34

1. About these instructions

Read the safety instructions carefully before use. Note the warnings on the device and in the operating instructions.

Always keep the operating instructions close to hand. If you sell the device or give it away, make sure you also hand over these instructions and the warranty card.

1.1. Symbols and keywords used in these instructions

DANGER!

Warning: immediate mortal danger!

WARNING!

Warning of possible risk of fatal injury and/or serious irreversible injuries!

BEWARE!

Please follow the instructions to prevent injuries and property damage!

ATTENTION!

Please follow the guidelines to avoid property damage!

NOTE!

Additional information on using the device.

NOTE!

Please follow the guidelines in the operating instructions!

WARNING!

Warning of risk of electric shock!

- Bullet point/information on operating steps and results

▶ Tasks to be performed

2. Package contents

WARNING!

Keep the packaging out of reach of children. There is a risk of suffocation.

When unpacking, ensure that the following parts are included:

• Coffee machine
• Filter holder
• Glass jug with lid
• Operating instructions and warranty card

3. Proper use

The device is designed for preparing coffee and also for grinding coffee beans.

This device is intended for home use or similar applications. It is not intended for use in kitchens for employees, shops, offices and other commercial areas; in agricultural estates; or by customers in hotels, motels and other places of accommodation or for bed & breakfast facilities.

Please note that we shall not be liable in cases of improper use:

• Do not modify the device without our consent and do not use any auxiliary equipment which we have not approved or supplied.
  -Use only spare parts and accessories which we have supplied or approved.
  -Heed all the information in these operating instructions, especially the safety information. Any other use is deemed improper and can cause personal injury or damage to the device.
• Do not use the device in extreme environmental conditions.

4. Safety instructions

4.1. Keep electrical equipment out of reach of children

• These devices may be used by children over the age of 8 and by persons with reduced physical, sensory or mental abilities or by those without experience and/or knowledge, if they are supervised or have been instructed in the safe use of the device and have understood the potential risks. Children must not play with the device. Cleaning and user maintenance must not be carried out by children, unless they are aged 8 or over and are supervised.
• Children younger than 8 should be kept away from the device and the mains cable.

WARNING!

Keep plastic packaging out of the reach of children.

There is a risk of suffocation!

4.2. Setting up

• Place the device on a heat-resistant, sturdy, level surface.
• Avoid the use of extension cables in order to prevent tripping.
• Never place the device on the edge of a table – it could tip over and fall.
• The device housing will become hot during operation. Therefore, only touch the device during operation on the buttons and handles provided for this purpose.
• Do not set up the device over a hotplate or other heat-generating devices (grill, deep fat fryer); this applies even if an extraction fan is installed above it.
• Never set up the device near to a sink.
• Leave a little space between this device and other devices or the wall to allow the air to circulate freely. Do not cover the device during operation.

4.3. Mains connection

• Only connect the device to a properly installed 220–240 V \~, 50 Hz safety plug socket that is located close to the place where you have set up the device. The socket outlet must be freely accessible so that you can unplug the device from the mains quickly if necessary.
• Ensure that the mains cable has been completely unwound during operation.
• Do not kink or crush the mains cable.
• Disconnect the mains cable when the device is not being used, during cleaning or if a fault occurs.
• Always remove the mains cable from the mains socket by grasping the plug – do not pull the cable itself.

4.4. Faults

• If the plug, cable or device is damaged, immediately remove the plug from the power supply.
• To avoid risks, never try to open and/or repair the device yourself. There is a risk of electric shock. In the event of a fault, contact our Service Centre or another suitable professional repair workshop.
• If the mains cable on the device is damaged, it must be replaced by the manufacturer, its customer service agent or another suitably qualified person. This is to avoid causing damage to the device.

4.5. Handling the device safely

• Never immerse the device in liquids!
• Do not use the device outdoors.
• Do not leave the device unattended during operation.
• Do not use the device under any circumstances when there is visible damage to the device, the mains cable or the plug.
  • Always hold the glass jug by the handle.

• Only pour cold water into the water tank.

• Do not add any other liquids except water to the water tank (except when descaling: see below).

• Do not pour any liquids other than water or coffee into the glass jug.
• Do not add any ingredients other than coffee beans to the coffee bean container.
• Do not leave any unused water in the water tank.
• Do not pour water into the water tank while the device is still hot. Allow the device to cool down between two brewing processes.
• Do not place the glass jug onto a hot plate, above a naked flame or in the microwave.

The coffee machine and its elements can become very hot during the brewing process. During operation, always use the handles provided to touch the glass jug, filter lid and device. Otherwise there is a risk of burns.

WARNING! ROTATING PARTS!

Never touch the grinding mechanism if the filter compartment is open or the device is operating. There is a risk of incurring a crush injury!

4.6. Cleaning the device

• Never immerse the coffee machine in water or other liquids!
• Remove the plug from the mains socket before cleaning the housing of the coffee machine.
• Allow the coffee machine to cool down completely.
• Clean the device using only a damp cloth and a mild soap solution that cannot damage the surface of the device.
  Follow the special instructions inside the device for descaling.

5. Overview of the device

Labeled diagram of a coffee maker with numbered parts for identification

1) Lid of the coffee bean container
2) Coffee bean container
3) Fold-up lid for the water tank
4) OPEN button for opening the filter compartment
5) Water level indicator
6) Operating panel
7) Glass jug
8) Filter holder
9) Drip stop function
10) Filter insert
11) Permanent filter
12) Grinder setting

6. Operating panel

123 11 10 9 8 7 2-12 4 5 6

1) TIMER LED. Lights up when the timer has been set.
2) GRINDER LED. Lights up when the grinder is switched off.
3) Display
4) CUPS button for setting the number of cups
5) HOUR button for setting the hours
6) MINUTE button for setting the minutes
7) PAUSE/START LED
8) PAUSE/START button
9) STRENGTH button. For setting the strength of the coffee based on the volume of water.
10) GRINDER button. For turning the grinder on or off.
11) TIMER button. For starting the coffee machine at a preset time.

7. Initial operation and use

Rinse out the glass jug thoroughly before using it for the first time.

Connect the coffee machine to a 220–240 V \~, 50 Hz mains socket.

Clean the coffee machine by carrying out three brewing processes using only water, without any coffee or filter (see "7.2.2. Brewing process using coffee powder" on page 30).
The filter holder has a handle for removal. The handle on the filter insert can be conveniently pulled out using the plastic tab on the front of the filter holder.
▶ Allow the coffee machine to cool down for approx. 5 minutes after every brewing process.

7.1. Setting the time

▶ Once the device has been connected to the power supply for the first time, the time display will flash (12:00).
▶ Press the MINUTE and HOUR buttons to set the time.
As soon as either the MINUTE or HOUR button has been pressed, the time display will stop flashing and the time will be set.

7.2. Preparing the coffee machine for the brewing process

▶ Open the lid of the water tank and fill it with the required volume of cold water for the desired number of cups using the scale on the water tank.

NOTE

As a result of the evaporation of water during the boiling process, the water level indicator on the water tank will not correspond exactly with the water level indicator on the glass jug. Only use the water level indicator in the water tank for filling the coffee machine.

Remove the glass jug from the warming plate and press the OPEN button to open the filter compartment.
Place the filter insert into the recess in the filter holder. The filter insert can only be inserted into the filter holder in one direction.
Place a paper coffee filter (size 1x4) or the supplied permanent filter into the filter holder. Ensure that the filter is positioned evenly in the filter insert.
▶ Close the filter holder again.
▶ Position the glass jug in the middle of the warming plate and ensure that the jug is positioned precisely underneath the filter holder.
The glass jug can only be inserted and removed at the front of the coffee machine.

7.2.1. Brewing process using coffee beans

▶ Ensure that the grinder is switched on (Grinder LED is not lit). If necessary, press the GRINDER button so that the GRINDER LED goes out.
▶ Open the lid of the coffee bean container.
▶ Add coffee beans (max. 200g) to the container and then replace the lid.

NOTE

To stop the beans from becoming damp, do not add too many coffee beans to the coffee bean container. In other words, do not push the beans down into the container.

▶ Set the fineness setting with the grinder setting function:

Coarser setting

▶ Set the desired number of cups (2, 4, 6, 8, 10 or 12 cups) by repeatedly pressing the CUPS button. If you do not set the number of cups, the largest number of cups (12 cups) will be used for the brewing process.

▶ Press the STRENGTH button repeatedly to adjust the strength of the coffee based on the amount of water used:

● Stronger coffee (less water)

Medium strength coffee (normal amount of water)

Weaker coffee (more water)

▶ Press the PAUSE/START button to start the brewing process. BREW appears on the display.

- The grinder will start operating after around 3 seconds and fills the coffee filter with ground coffee.

• The brewing process will then start.

- Once the brewing process has ended, BREW will disappear from the display and a signal tone will sound.

7.2.2. Brewing process using coffee powder

▶ Add the corresponding amount of coffee powder to the filter. The recommended amount is 1 heaped teaspoon per cup.
▶ Close the filter holder again.
▶ Set the desired number of cups (2, 4, 6, 8, 10 or 12 cups) by repeatedly pressing the CUPS button. If you do not set the number of cups, the largest number of cups (12 cups) will be used for the brewing process.
▶ Press the STRENGTH button repeatedly to adjust the strength of the coffee based on the amount of water used:

● Stronger coffee (less water)

Medium strength coffee (normal amount of water)

Weaker coffee (more water)

▶ Ensure that the grinder is switched off (GRINDER LED is lit). If necessary, press the GRINDER button so that the Grinder LED lights up.

▶ Press the PAUSE/START button to start the brewing process. BREW appears on the display and the brewing process will start.

Once the brewing process has ended, BREW will disappear from the display and a signal tone will sound.

7.2.3. Drip stop function

The drip stop function enables you to serve the already finished coffee while the brewing process is still in progress.

• Carefully remove the glass jug from the warming plate. The flow of coffee from the filter to the jug will be interrupted; the coffee will now accumulate in the filter.
  Place the glass jug under the filter again within 30 seconds. Otherwise there is a risk that the filter will overflow.

The strength of the coffee that is taken in the middle of the brewing process may differ from the strength of the coffee after the complete brewing process.

7.3. Using the timer

NOTE

The time must be set before you can use the timer.

Prepare the coffee machine for a brewing process using coffee coffee powder as previously described but do not start the brewing

▶ Hold down the TIMER button until the time display flashes.
▶ Use the HOUR and MINUTE buttons to enter a time at which the brewing process should start and confirm your entry by pressing the TIMER button again.
In order to switch on the timer, press the TIMER button until the time symbol appears on the display.

The coffee machine will start the brewing process at the preset time.

In order to switch off the timer setting, briefly press the TIMER button until the time symbol on the display disappears.

7.4. End of the brewing process/automatic switch-off

You can let the coffee stand for a while in the glass jug on the warming plate. However, please note that the aroma of the coffee will deteriorate after it has stood on the warming plate for a long period of time.

The coffee machine will switch off automatically after around 40 minutes.

Do not leave an empty glass jug standing on the hot warming plate.

7.5. Cleaning and descaling

Allow the coffee machine to cool down before cleaning it and pull the plug out of the mains socket. Remove the glass jug and, if necessary, both filters from the device.

▶ Only clean the outside of the coffee machine using a damp cloth and, if necessary, some mild washing-up liquid. In particular, remove any coffee stains from the warming plate.
▶ You can wash the glass jug in a dishwasher. If you wash the jug by hand, do not use any abrasive items or products that could damage the glass!
The filter insert can be cleaned by hand.

7.5.1. Emptying the grinder

If you intend to store the coffee machine or not use it for a long period of time, it is necessary to empty the grinder because otherwise any beans remaining in the grinder could become mouldy.

Remove the glass jug and the filter insert and make sure that the water tank is empty.
▶ Tilt the machine so that any remaining beans fall out of the top of the coffee bean container.
▶ Return the coffee machine to an upright position and plug it into the mains socket.
▶ Open the filter compartment.

WARNING! ROTATING PARTS!

Never touch the grinding mechanism if the filter compartment is open or the device is operating. There is a risk of incurring a crush injury!

▶ If necessary, place a small bowl on the warming plate.
▶ Start a brewing process using coffee beans, although without adding any water or beans.
▶ Once the remaining coffee stops falling out of the bottom of the grinder, press the PAUSE/START button to cancel the brewing process.

WARNING!

Do not allow the brewing process to run "dry" for longer than 1 minute. There is a risk of overheating that could result in damage to the device!

Remove the plug from the mains socket once the process has been completed.

7.5.2. Descaling

In order to prolong the device's service life and to keep brewing times short, the coffee machine must be regularly descaling. The time interval depends on the hardness of the water and the frequency with which the device is used. The machine should be descaled at the latest when the brewing process has become significantly longer. We recommend an environmentally friendly descaling process using vinegar or citric acid:

▶ Measure out two cups of vinegar or 2 heaped tablespoons of citric acid crystals and add this to eight cups of water.
▶ Add the solution to the water tank, close the lid of the filter holder and place the jug underneath.
▶ Allow the solution to run through the coffee machine, if necessary a number of times.
▶ Rinse the glass jug and the filter holder thoroughly afterwards.
▶ Finally, fill the coffee machine with fresh water a number of times and run the machine.

If you want to use a commercial descaler (chemical product), observe the instructions provided by the manufacturer of the product.

Do not let the chemical descaler drip onto the housing or the warming plate!

8. Disposal

Packaging

Your device has been packaged to protect it against transportation damage. Packaging is raw material and can be re-used or added to the recycling system.

Device

Old devices should not be disposed of with the normal household rubbish.

As per Directive 2012/19/EU, the device must be properly disposed of at the end of its service life.

This ensures that valuable resources contained in the device are recycled and do not burden the environment.

Bring your device to a waste collection centre for electric waste or a recycling centre.

Contact your local waste disposal company or your local authority for more information on this subject.

9. Technical data

Voltage supply 220–240 V \~ 50 Hz

Output

900-1050

W

Filling volume for water approx. 1.5l/approx. 12 cups

Filling volume for coffee beans approx. 259 g

Intertek

Subject to technical modifications!

10. Legal notice

Copyright © 2014

All rights reserved.

This operating manual is protected by copyright.

Mechanical, electronic and any other form of reproduction is prohibited without the written permission of the manufacturer.

The owner of the copyright is:

Medion AG

Am Zehnthof 77

45307 Essen

Germany

These instructions can be re-ordered from the Service Hotline and are also available for download via the service web page at www.medionservice.de.

You can also scan the QR code above to download the instructions onto your mobile device via the service portal.

QR code image containing encoded data, no visible human-readable text

Sommaire

DE

Labeled diagram of a coffee maker with numbered parts for identification

- Puis la percolation commence.

Symbol of a trash bin crossed out by two crossed lines, with no text or labels present.

Appareil

modifications techniques !

QR code image containing encoded data, no visible human-readable text

Inhoud

Labeled diagram of a coffee maker with numbered parts for identification

QR code image containing encoded data, no visible human-readable text

Labeled diagram of a coffee maker with numbered parts for identification

1) Bønnebeholderens låg
2) Bønnebeholder
3) Opklappeligt låg på vandtanken
4) Knappen OPEN til åbning af filterrummet
5) Vandstandsindikator
6) Betjeningsenhed
7) Glaskande
8) Filterbeholder
9) Drypværn
10) Filterindsats
11) Permanent filter
12) Kværnindstilling

6. Betjeningsenhed

123 11 10 9 8 7 2-12 4 5 6

QR code image containing encoded data, no visible human-readable text

5. Restricted Warranty (United Kingdom)

5.1. General Conditions of Warranty

5.1.1. General

This warranty covers defects relating to workmanship and manufacture in MEDION products. The period during which this warranty is valid and during which claims against the warranty can be made to MEDION must be in accordance with the following terms in order to be considered eligible:

- Is effective from the date of purchase or receipt of the MEDION product from an authorised seller of MEDION products;

and

- expires at the end of the warranty period.

For the warranty to be valid, you must:

• provide suitable evidence of purchase, a copy of the original purchase receipt from an authorised seller of MEDION products is preferred;

or

- register your product within 28 days of purchase online at www.MEDION.co.uk.

Please keep the original purchase receipt in a safe place. MEDION and its authorised sellers reserve the right to refuse a repair under warranty or a warranty confirmation if a proof of purchase [or registration of purchase] cannot be established, or has not been, submitted.

When it is necessary to return your product for repair please ensure that your product is suitably packed for transportation.

Provided that your product is still within warranty (please check the duration of the warranty period as described above) and is eligible for repair or replacement under the terms of the warranty, to return your product, please telephone MEDION on the service hotline number. You will be sent a pre-paid transportation box suitable for returning your product to MEDION or a voucher.

PLEASE MAKE SURE THAT YOU HAVE A BACKUP COPY OF ALL DATA ON THE PRODUCT BEFORE RETURNING THE PRODUCT TO MEDION.

MEDION shall bear the costs of postage and packaging for returning the product and the transportation risk. However, if following examination of the defective product in question, MEDION, in its reasonable opinion, considers that the defect has been caused by:

- your operating and/or using the product other than as instructed in the accompanying documentation;

- damage caused in transit as a result of your negligence in packaging of the product; and/or

- otherwise than in accordance with the terms of this warranty;

This warranty shall be void and you may be required by MEDION to reimburse MEDION for the reasonable costs of postage and packaging before MEDION will return the product to you. If so and you would still like MEDION to repair or replace the

product, MEDION may do so but you will be charged MEDION's standard rates for repair and replacement for this service.

Before returning the product, please contact MEDION via the service hotline or via the internet www.MEDION.co.uk. You will receive a reference number (RMA No.). Please mark the outside of your package to ensure that this reference number is clearly visible. Please submit a letter containing as much detailed information as possible and, a full description of the defect or fault.

This should include:

• a description of the fault;
- when it occurred, how long it has been evident and how frequently it occurs;
- any errors message(s) displayed when using the product;
- a description of the circumstance(s) and conditions in which the fault occurs; and
- whether it is an intermittent or persistent fault.

This will greatly assist MEDION in identifying the defect, when submitted together with the defective product.

Unless otherwise instructed by a MEDION representative in all cases, the product must be returned complete with all parts which were included with the original product. Incomplete contents of the returned package may lead to a delay in the repair or replacement. MEDION does not accept any liability for any additionally submitted material(s) which were not supplied with the original MEDION product.

This warranty does not affect your statutory rights in any way and is subject to the applicable legal statutes of the country where the product was sold to you by an authorised MEDION seller.

5.1.2. Scope

Subject to any exclusions set out within this warranty, where there is a defect in your MEDION product covered by this warranty, MEDION will repair or replace the MEDION product. The decision whether to repair or replace the product will be made solely at the discretion of MEDION. MEDION may, in its own discretion, replace the product returned for repair under warranty with a replacement product that is either identical or, in the event that such product(s) are no longer available, a product of equal or superior specification and quality.

No warranty is given for batteries or rechargeable batteries or for consumable materials subject to wear and tear, i.e. for parts which have to be replaced periodically during the normal use of the product, such as video-projector lamp.

Non critical failures that fall within industry specified tolerances e.g. noise, LCD pixels are not covered by this warranty. Please consult the appropriate section in your user or instruction manual for this product for exact specifications and tolerances.

To the extent which is permitted under law, MEDION will accept no liability for burnt-in images on plasma or LCD products as a result of normal wear and tear during the operation of the product. Please refer to your user or instruction manual for this product for detailed operating instructions for your plasma or LCD product.

The warranty does not cover errors relating to the playback of data media in an incompatible format or created with unsuitable software.

If it is found during repair or assessment that the defect concerned is not covered under warranty, MEDION reserves the right to invoice you for all reasonable costs incurred by MEDION. These costs will be in relation to the return of the product, including reasonable administration costs, plus reasonable costs for materials used and labour provided when repairing or replacing the product. This is subject to MEDION providing you with an estimate for carrying out such work prior to costs being incurred and that you have accepted the estimate.

You are entitled to seek independent advice or consultation relating to your product or any of MEDION's findings. MEDION will not be liable for any costs incurred to you when doing so.

5.1.3. Exclusion from warranty

To the extent permitted by law, this warranty shall be void in the event that defects or loss caused by:

• failure and damage resulting from the operation of the product in an environment other than that recommended in the accompanying user or instruction manual (e.g. in direct sunlight or in a damp room);
  • accidental damage;
• use other than in accordance with the accompanying user or instruction manual;
• modifications, conversions, expansions, maintenance and/or repairs made to the MEDION product by unauthorised repairers or use of unauthorised third party parts;

- negligence;

• virus attack or software errors;

or

- improper transportation or packaging during return of the product.

- This warranty will also be considered void if labels or serial numbers of the product or of a component of the product are modified or made illegible.

- To the extent permitted by law, MEDION shall; only be responsible for losses which are a reasonably foreseeable consequence of the relevant defect in the product; MEDION will not be responsible for any costs incurred in relation to software configuration; economic loss; loss of opportunity; loss of income; or loss of data or software arising out of its repair or replacement of a MEDION product under this warranty

5.1.4. Service Hotline

Before returning the product to MEDION you must contact us using the service hotline or via the internet (www.MEDION.co.uk). You will receive further instructions for making your claim under warranty when you call.

The price of your call will be stated at the beginning of the call.

5.2. Special warranty conditions for MEDION PC, notebook, pocket PC (PDA) and navigation devices (PNA)

The following terms apply to MEDION PC, notebook, desktop, pocket PC and laptop products and optional items included with such products. If one of these items has a fault, you also have a warranty claim for its repair or replacement, from MEDION. The warranty covers the costs of materials and labour for repairing or replacing the defective MEDION product or the optional item in question.

Hardware connected to your product that was not produced or marketed by MEDION can invalidate the warranty if MEDION can reasonably demonstrate that damage to the MEDION product or of the optional item included with the delivery was caused by such hardware. You are entitled to seek independent advice or consultation relating to your product or any of MEDION's findings. MEDION will not be liable for any costs incurred to you when doing so.

This warranty is restricted in relation to any pre-installed operating system as well as to application programme software that is included with the MEDION product in question. This warranty is restricted as follows:

For pre-installed operating system as well as to application programme software included in the MEDION product, MEDION only guarantees the data media (e.g. the diskettes and CD-ROMs) upon which this software is delivered and warrants that such data media shall be free from material and processing defects for a period of 90 days from the date of purchase of the MEDION product from an authorised seller of MEDION. MEDION will replace defective data media free of charge.

Any claims in respect of defective pre-installed operating system as well as to application programme software are hereby expressly excluded and you should contact the relevant licensor or copyright owner of the defective software in question. MEDION does not guarantee that any software supplied with MEDION products will function without interruption, will be free from errors or that it will fulfil your requirements. MEDION does not guarantee the 100% accuracy of the maps provided with the Navigation device.

It may be necessary to delete all data in the product in order to repair the MEDI-ON product. PLEASE MAKE SURE THAT YOU HAVE A BACKUP COPY OF ALL DATA ON THE PRODUCT BEFORE RETURNING THE PRODUCT TO MEDION. To the extent permitted by law, MEDION excludes all liability for loss of data and MEDION recommends in all cases that you back up all data on your MEDION product before returning the product to MEDION.

5.3. Special warranty conditions for repair on site or replacement on site

If a claim for repair or replacement on site is included with the product, the special warranty conditions for repair or replacement of your MEDION product on site apply.

The following provisions must be made by you for carrying out repairs or replacements on site:

• MEDION or its authorised personnel must have unrestricted, safe and immediate access to the products.
• Telecommunication facilities required by MEDION or its authorised personnel for proper execution of your order, for testing and diagnostic purposes and for remedying faults are provided by you at your own expense.
• You are responsible yourself for restoring the application software after the repair services have been carried out by MEDION or its authorised personnel.
• You must take all other necessary steps to enable MEDION or its authorised personnel to carry out your order properly.
• You are responsible yourself for connecting and configuring any existing external peripheral products after MEDION or its authorised personnel have carried out their repairs.
• The free cancellation period for repairs or replacements on site is 24 hours, thereafter our reasonable costs resulting from late or missing cancellation shall be invoiced at your expense.

6. Service Address

① 0871 37 61 020 📋 01793 715716

(Costs 7p/min from a BT landline, mobile costs may be higher)

Mo - Fr: 08:00 - 20:00

Sa - Su: 10:00 - 16:00

www.medion.co.uk

@ To contact us by email please visit the „Service“ section of our website at www.medion.co.uk.

7. Garantie commerciale limitee (France)