iZi Go Modular X1 i-Size - Car seat BESAFE - Free user manual and instructions

USER MANUAL iZi Go Modular X1 i-Size BESAFE

BeSafe® BEASER/NAVIG BEAFETY USER MANUAL Rearfacing only Stature height 40-75 cm Max. weight: 13 kg Age approx.: 0-12 mths UN regulation no. R129-1-Size BeSafe IZI® Go Modular I-Size

Technical diagram showing car seat assembly and safety monitoring system with labeled components

3 click! 4 > 25 cm 5

Thank you for choosing BeSafe I2I Go Modular

It is important that you read this user marva. BEFORE installing your seat, incorrect installation can could undergo your choice.

! Vital Information

• The child sea MUST NOT be installed in a front

passenger seat WITH AN ACTIVATED AIRDAG

- 12. Co. M6054 can be installed reactivating on 12 Months Size base or can be installed rearacing with a 3 port

approved according to UNFCCC Regulation No.15 or other

standards

4.10 Co-moduler is approved for children with a stature help. 75 cm with a over-stroke of 13 h.

• The harness s. rans must always be lacked when the child is in

12.34

• The harness scraps must be lightened with you, slack and no, twisted.

• The sine wave spectra signals. Magneto-circulation

electronic equipment such as pccrakers.

• I'll sell any price in this 100's many weeks to deposit in the skin. • Every baby making it giving thanks to a room, plus the world

- Remove the baby custom following the white hedge after the child's scale, then all can start their 6 months.

• The white wedge in the bottom of the baby cushion can be removed

when the child needs more space under the back of the harness

system, 2018, 31:1965

• Remover the PaaS space controllers on both sides from the head and cushion when the child older than 3 months or if the head is set

"While anyone of when the baby has a status paint higher than all

cm. H2* on all modeled

- After an accident, the seat must be replaced. Although it may miss

undamaged, if you were to have another accident, the seat may not

be able to protect your child to the level to which it was design

• PRESENT THE TEST FROM BEAMING ITEMS

- Make sure you can fit no more than one finger between the hammers.

and your this item

- DO NOT attempt to dismantle modify or add any part to the seat.

Warranty will be void if non-original parts or accessories are used

- Never have your child unattended in the seat.

• Make sure all passengers are informed about how to release your

child in case of emergency.

- Make sure luggage or other objects are properly secured. Unsecured

luggage may cause severe injuries to children and adults in case

of accidents.

- Never use the best w/o cut, the cover. The cover is a safety culture

and may only be replaced by a ^4 -of great essence cover.

- 0519.250 and aggressive stress in construct on material of the coat

• De-Safe advises that child sea a ship is not broken and is still opened.

hard

- KIPP is user menu for later use with one set

- 0.5 NOT use the seat for larger than 7 years. Due to spring, the

quality of the material may change

Nachpar HS 12/58-2019 using the seat as a

recinded cradic

NOTANT REED FOR FUTURE REFERENCE

the entire price is \$150,000.

Never leave the child unattended.

Do not use the seal as recound oracle else your child can sit yesterday.

91.01215-0.

This recurred crucial is not intended to prolonged periods or succeeding. It is clameness in use this recurred crucial on its study of our

a

• A survey question (in the case)

This resigned oracle caps not replace a set or a box. Should your child

need to sleep. Then I should be placed in a suitable oct or bed.

- Do not use the reclined cradle if any components are broken

or missing

- Do not use accessories or replacements, parts other than those

approved by the manufacturer

- If in doubt, consult either the correct manufacturer or the retailer.

Preparing to install

• Carrying handle (1a)
• Head cushion (1b)
  • Head space reducer (1c)
• Handle release buttons (2x) (1d)
• Shoulder straps (2x) (1e)
• Hip belt hook (2x) (1f)
• Baby cushion (1g)
• Harness buckle (1h)
• Sun canopy (1i)
  • Stroller release handles (4x) (1j)
• Shoulder belt hook (1k)
• Harness height adjuster (11)
  • Stroller adapter house (1m)

Installation of the seat on the i-Size base

1. Check if the ISOfix and floor support indicators on the base are green. (2)
2. Position the seat in the correct position on the base until it clicks with the base and the indicator at the front shows green. (3)
3. Leave the carrying handle up in the carrying position.
4. When the seat is positioned rearfacing on the back seat of the vehicle, you should, if possible, push the front seat of the vehicle backwards, so that it is in contact with the child seat. If it is not possible to obtain contact with the child seat, push the back rest of the front seat of the vehicle forward as far as possible. (4)
5. The seat is delivered with removable SIP+ (side impact protection +). This extra side impact protection should be used on the doorside of the vehicle. It can be connected by slotting between the seatshell and the fabric. The seat already offers high level integrated side impact protection. This extra side impact protection improves the protection in the side impact still further. (Not on all models) Do not use the SIP+ on the seat when the space between seat and door of the vehicle is too small, which might lead to a situation where the seat is not positioned correctly on the vehicle seat.

Removal of the seat of the i-Size base

- The seat can be taken off by pulling the seat release handle at the front of the base.

Belt installation

1. Position the seat on the vehicle seat. Make sure the carrying handle is up in the carrying position. (5)
2. Guide the hip belt of the 3-point-belt over the blue sections under the hip belt hooks and fasten the seat belt with a 'click'. (6)
3. Guide the shoulder belt over the blue section through the shoulder belt hook at the rear side of the seat shell. (7)
4. Tighten the 3-point belt by pulling the belt through the hip belt hooks and through the shoulder belt hook until it is as tight as possible. (8)
5. Leave the carrying handle up in carrying position.

Positioning of the child

1. Check that the shoulder strap slots are level with your child's shoulders. (9)
2. Pull the shoulder straps up while pressing the button of the central adjuster. (10)
3. Open the harness buckle. (11)
4. The height of the shoulder straps and the head cushion can be adjusted by pulling the release handle upwards at the back of the seat and pulling the handle up or down. (12)
5. Position the shoulder straps over the marking at the sides of the seat to use the magnets to keep the harness open while you position the child. (13)
6. When the child is positioned, place the shoulder straps over the child's shoulders and close the buckle: CLICK! (14)
7. Pull the harness strap through the central adjuster in the direction of the arrow straight up/forwards. Continue pulling until the harness is a comfortable but a firm fit. (15)
8. You can protect your child against the sun by raising the sun canopy.

Baby cushion

• The baby cushion offers extra comfort for young babies. As baby grows the thickness of the baby cushions can be adjusted.
  • 0-4 m (16)
  • 4 m + (17)

Head cushion

- Remove the head space reducers on both sides from the headrest cushion when the child is older then 3 months or if the head is not fitting anymore or when the baby has a stature height higher than 60 cm. (18) (Not on all models)

Using the iZi Go with a pushchair

- The iZi Go can be installed on a range of pushchairs. For a complete list check www.besafe.com

Installation on a pushchair

- Align the stroller adapter housings above the adapters of the pushchair and push straight down, click! (2x) (19)

Removing from a pushchair

1. Move the carrying handle into carrying position.
2. Push the pushchair release levers up at both sides while lifting the seat vertically from the pushchair. (20)
3. You can also release the seat from the pushchair by pushing the release levers beside the carrying handle towards the front of the car seat. (21)

Removing and refitting the cover

- Do take care when you remove the cover, as re-fitting the cover is done in reverse.

! Warning: potential misuse

• The child seat MUST NOT be installed in a front passenger seat WITH AN ACTIVATED AIRBAG.
• The floor support must always be used. Make sure that the floor support is fully pushed down.
• Make sure the indicators are green before you drive.

Guarantee

• Should this product prove faulty within 24 months of purchase due to materials or manufacturing fault, except covers and harness straps, please return it to the original place of purchase.
• The guarantee is only valid when you use your seat appropriately and with care. Please contact your retailer, they will decide if the seat will be returned to the manufacturer for repair. Replacement or return cannot be claimed. The guarantee is not extended through repair.
• The guarantee expires: when there is no receipt, when defects are caused by incorrect and improper use, when defects are caused by abuse, misuse or negligence.

Takk for at du valgte BeSafe iZi Go Modular

BeSafe® SCANDINAVIAN SAFETY