302209 - Clock Bearware - Free user manual and instructions

USER MANUAL 302209 Bearware

Abstract red graphic design resembling a stylized bear or bear shape (no text or symbols)

BEARWARE

Thank you for choosing a BEARWARE product. Please read the following user manual carefully to have an enjoyable experience with your purchased product.

1 Scope of supply

• Weather station
• User manual

2 Technical data

Power supply 1x LR1130 (button cell)
Dimensions (HxWxD) 110mm x 55mm x 28mm
Weight 50 g (without battery)
Features	Indoor temperatureDate displayAlarm functionTemperature in °C and °FHumidityForecast iconsMoon phase displaySnooze functionmin/max. values of temperature and humidity12/24 hour time formats

3 Initial use

Open the battery compartment at the back of the weather station and insert two LR1130 batteries into the upper battery slot. Close the battery compartment again.

3.1 Functions

Press the "MIN/MAX" button to display the maximum or minimum temperature and humidity. If you wish to delete the maximum or minimum temperature values, it is necessary to display the respective value and then press and hold the "MIN/MAX" button till the respective value disappears.

Press the "SNZ" button to enable the Snooze function. Press any other button except the "SNZ" button to cancel the alarm. Once the weather station is in Snooze mode, the alarm sounds again after about 5 minutes.

4 Time

Proceed as follows to set the time:

• Press the "MODE" button till the time is shown in the display.
• Once the time is displayed, press and hold the "Set" button till the time on the display starts to flash. The settings can be made using the "ADJ" button. Confirm using the "Set" button. The sequence for setting the time is as follows: 12/24 hrs->Hours->Minutes.
• Then press the "MODE" button to save the settings and to exit the menu.

4.1 Calendar/date

• Press the "MODE" button till the date is shown in the display.
• Press and hold the "Set" button till the date starts to flash. The settings can be made using the "ADJ" button. Confirm using the "Set" button. The sequence for setting the date is as follows: Year -> Month -> Day
• Then press the "MODE" button to save the settings and to exit the menu.

4.2 Alarm

• Press the "MODE" button till the alarm time is shown in the display.
• Press and hold the "Set" button till the alarm time starts to flash. The settings can be made using the "ADJ" button. Confirm using the "Set" button. Once the alarm time is shown in the display, press the "ADJ" button to switch the alarm on / off. The sequence for setting the alarm is as follows: Alarm sound On -> Alarm enabled -> Alarm enabled and alarm sound On

5 Additional information

• Replace the battery if the display becomes dim or the alarm sound is too low.
• If you notice that the product does not contain batteries, then you should not use it.
• If the LCD display does not show any image or it is faulty, try to remove and insert the battery again.
• Press the SET button to select between °C and °F.

6 Safety instructions and liability disclaimer

Never try to open the device to carry out repairs or conversions. Avoid contact with mains voltages. Do not short-circuit the product. The device is not certified for use in the open air; only use it in dry conditions. Protect it from high humidity, water and snow. Keep it away from high temperatures. Do not subject the device to sudden changes in temperature or heavy vibration as this might damage electronic components. Examine the device for damage before using it. The unit should not be used if it has received an impact or has been damaged in any other way. Please observe national regulations and restrictions. Do not use the device for purposes other than those described in the instructions. This product is not a toy. Keep it out of the reach of children or mentally impaired persons. Any repair or alteration to the device not carried out by the original supplier, will invalidate the warranty or guarantee. The product may only be used by persons who have read and understood these instructions. The device specifications may change without any separate prior notice to this effect.

7 Disposal instructions

Electrical and electronic devices may only be disposed of in accordance with the European WEEE Directive and not with household rubbish. Components must be disposed of or recycled separately as dangerous, toxic elements can inflict sustained damage on the environment if they are disposed of incorrectly. As a consumer, you are bound by the Electrical and Electronic Devices Act (ElektroG) to return electrical and electronic goods free of charge at the end of their useful life to the manufacturer, the place of purchase or to specially set up, public collection points. The details in each case are governed by national law.

The symbol on the product, the operating instructions and/or the packaging refers to these regulations. By separating materials in this way, recycling and disposing of old devices, you are making an important contribution towards protecting our environment.

8 Instructions on the disposal of batteries

With regard to the sale of batteries or the supply of devices containing batteries, the supplier is obliged to draw the customer's attention to the following:

As the end user, the customer has a statutory obligation to return used batteries. He can return old batteries stocked or previously stocked by the supplier in the form of new batteries to the supplier's despatch warehouse (despatch address) free of charge. The symbols shown on the batteries have the following meanings: Pb = battery contains more than 0.004 percent by mass of lead, Cd = battery contains more than 0.002 percent by mass of cadmium, Hg = battery contains more than 0.0005 percent by mass of quicksilver.

The symbol of the rubbish bin with a cross through it indicates that the battery may not be put in household waste.

WEEE guideline: 2012/19/EU

WEEE register number: DE 94495668

WD Plus GmbH, herewith declares that this product 302209/20160615FZ004 conforms to the principle requirements and other relevant stipulations. The complete Declaration of Conformity can be obtained from: WD Plus GmbH, Wohlenbergstraße 16, 30719 Hanover