30.3072.01.90 - Thermometer TFA - Free user manual and instructions

USER MANUAL 30.3072.01.90 TFA

service/downloads/instruction-manuals

CE UK CA

Thank you for choosing this instrument from TFA.

Before you use this product

• Please make sure you read the instruction manual carefully.
• The operating instructions are enclosed with the device or can be downloaded at www.tfa-dostmann.de/en/service/downloads/instruction-manuals
• This product should only be used as described within these instructions.
• Following and respecting the instructions in your manual will prevent damage to your instrument and loss of your statutory rights arising from defects due to incorrect use.
• Please take particular note of the safety advice!
• Please keep this instruction manual safe for future reference.

F Mode d'emploi

• Wireless thermometer (base station)
  • Outdoor transmitter Cat.-No. 30.3250.02
• Instruction manual

2. Range of application and all the benefits of your new instrument at a glance

• Outdoor temperature via up to 3 wireless outdoor transmitters (max. 100 m)
  • Indication of indoor temperature
• Indication of maximum and minimum values showing time and date of recording with manual or auto-reset
  • Radio-controlled clock with date
  • Wall mounting or table stand

3. For your safety

• This product is exclusively intended for the range of application described above.
• This product should only be used as described within these instructions.

WARNING

• Keep the devices and the batteries out of reach of children.
• Small parts can be swallowed by children (under three years old).
• Batteries contain harmful acids and may be hazardous if swallowed. If a battery is swallowed, this can lead to serious internal burns and death within two hours. If you suspect a battery could have been swallowed or otherwise caught in the body, seek medical help immediately.
• Batteries must not be thrown into a fire, short-circuited, taken apart or recharged. Risk of explosion!
• Low batteries should be changed as soon as possible to prevent damage caused by leaking. Make sure the polarities are correct. Never use a combination of old and new batteries together, nor batteries of different types.
• Remove the batteries if the device will not be used for an extended period of time.

Wireless Thermometer

- Avoid contact with skin, eyes and mucous membranes when handling leaking batteries. In case of contact, immediately rinse the affected areas with water and consult a doctor.

CAUTION

• Unauthorised repairs, alterations or changes to the product are prohibited.
• Do not expose the device to extreme temperatures, vibrations or shocks.
• Clean the device with a soft damp cloth. Do not use solvents or scouring agents.
• The base station is only suitable for indoor use. Protect it from moisture!
  • The transmitter is splashproof, but not watertight.

4. Elements

Base station (Receiver)

A: Display (Fig. 1):

A 1: Time
A 2: DCF reception symbol
A 3: Symbol for auto-reset of the maximum-minimum values
A 4: Seconds
A 5: Date
A 6: Battery symbol for the base station
A 7: Indoor temperature
A 8: Reception symbol for the transmitter
A 9: Battery symbol for the transmitter
A 10: Outdoor temperature
A 11: Max.-Min. indicator
A 12: Circle symbol for the alternating channel
A 13: Channel number

B: Buttons (Fig. 1):

B 1: SET/MAX/MIN button

B 2: +/CHANNEL button

C: Housing (Fig. 2):

C 1: Wall mounting hole
C 2: Battery compartment
C 3: Table stand (removable)

Wireless Thermometer

Transmitter

D: Display (Fig. 3):

D 1: Channel 1,2,3
D 2: Transmission signal
D 3: Battery symbol for the transmitter
D 4: Outdoor temperature

E: Housing (Fig. 4):

E 1: Battery compartment
E 2: Support for wall mounting or table standing
E 3: Indentations for the holder for wall mounting

F: Buttons in the battery compartment (Fig. 4):

F 1: TX button
F 2: 1 2 3 switch for channel selection

5. Getting started

5.1 Insert the batteries

• Place the instruments on a table at a distance of about 1.5 meters from each other. Avoid being close to possible sources of interference such as electronic devices and radio equipment.
• Open the battery compartment of the transmitter and insert two new AA 1.5 V batteries, polarity as illustrated. All LCD segments will be displayed for a short moment. The display shows the temperature. The switch is set to channel 1.
• Close the battery compartment.
• Remove the protective film from the base station display.
• Open the battery compartment of the base station.
• Insert two new AA 1.5 V batteries, polarity as illustrated. All LCD segments will be displayed for a short moment. The indoor temperature appears on the display.
• Close the battery compartment.

5.2 Reception of outdoor transmitter

• The base station will scan the outdoor temperature and the reception symbol flashes.
• If the reception is successful, the outdoor temperature and the reception symbol appear steadily on the base station display.

Wireless Thermometer

• If the reception of the outdoor temperature fails, “- -,-” remains on the display. Check the batteries and try it again.
• You can also activate the reception manually. Press and hold the + / CHANNEL button on the base station for three seconds. The reception symbol for the outdoor transmitter will be flashing.
• Press the TX button in the transmitter's battery compartment. The transmission of the outdoor data takes place immediately and if the reception is successful, the outdoor temperature appears on the base station display.

5.3 Reception of the DCF frequency signal

• After the reception of the outdoor values, the clock will now scan the DCF frequency signal and the DCF symbol flashes on the display.
• When the time code is successfully received after 3-10 minutes, the radio-controlled time, the date and the DCF symbol will be shown steadily on the display.
• The DCF reception always takes place at 1:00, 2:00 and 3:00 o'clock in the morning. If the signal is not successfully received, further attempts will be taken at 4:00 and 5:00 o'clock.
• If the clock cannot detect the DCF-signal (e.g. due to interference, transmitting distance, etc.), the time can be set manually.
• The clock will then work as a normal quartz clock (see: "Manual settings").

Note on radio-controlled time

• The time is transmitted from an atomic clock near Frankfurt am Main by a DCF-77 (77.5 kHz) frequency signal with a range of about 1,500 km. Your radio-controlled clock receives the signal, converts it and always shows the exact time. The adjustment of Daylight Saving Time and Standard Time is also automatic.
• During night-time, the atmospheric interference is usually less severe. A single daily reception is adequate to keep the accuracy deviation under 1 second. In extreme cases, please place the unit close to a window to improve reception.

Wireless Thermometer

6. Operation

6.1 Manual settings

• Press and hold the SET/MAX/MIN button for three seconds to enter the setting mode.
• The first adjustable value flashes on the display.
• Use the + / CHANNEL button to make the desired setting.
• Confirm with the SET/MAX/MIN button and go to the next setting.

• The sequence is shown as follows:
- DCF reception ON/OFF (default: DCF ON)
- Time zone -12/+12 (default: DCF 00H)
- Hours, minutes
- Year, month, day
- Automatic reset of the maximum and minimum values ON/OFF (default: AUTO OFF MAX MIN)

- Press and hold the +/-CHANNEL button in the respective setting mode for quick setting. The device will automatically quit the setting mode if no button is pressed for 20 seconds.

6.1.1 DCF reception

• By default, the DCF reception is activated (DCF ON) and after successful reception of the DCF signal no manual time setting is necessary.
• Once the DCF time reception is deactivated (DCF OFF), the clock and date must be manually set. No time zone will appear.
• If the DCF reception is activated, the manually set time will be overwritten by the DCF time when the signal is received successfully.

6.1.2 Time zone setting

• In the setting mode you can make the time zone correction.
• The time zone correction is needed for countries where the DCF signal can be received but the time zone is different from the DCF time (e.g. +1=one hour plus).

6.1.3 Automatic reset of the maximum and minimum values

- In the setting mode you can activate (AUTO ON) or deactivate (AUTO OFF) the automatic reset of the maximum and minimum values.

Wireless Thermometer

• If the automatic reset is activated, AUTO appears on the display besides the current time display.
• All maximum and minimum values will be reset automatically every midnight at 0:00.

6.2 Maximum/Minimum function

6.2.1 Indication of maximum and minimum values

• Press several times the SET/MAX/MIN button in normal mode.
• You can now see the highest (MAX) and lowest values (MIN) since the last reset with time and date of recording.
• The sequence is shown as follows: indoor temperature (MAX), indoor temperature (MIN), outdoor temperature (MAX), outdoor temperature (MIN).
• Press the SET/MAX/MIN button again to return to normal mode.
• The device will automatically quit the MAX/MIN mode if no button is pressed.

6.2.2 Reset of maximum and minimum values a) Manual reset

• Press and hold the SET/MAX/MIN button while the highest or lowest values are displayed. The values will be deleted individually and reset to the current state.
• Provided that in the setting mode the automatic reset is activated (AUTO ON). The AUTO symbol appears on the display.
• All maximum and minimum values will be reset automatically every midnight at 0:00.
• An interim manual reset is still possible.

b) Automatic reset

7. Installation

• When placed outdoors, choose a shady and dry place for the transmitter. Direct sunlight may trigger incorrect measurement and continuous humidity damages the electronic components needlessly.
• Before the final installation, make sure that the measured values are transmitted from the transmitter at the desired installation site to the base station.
• Do not use the base station in the vicinity of radiators, other sources of heat or in direct sunlight.

Wireless Thermometer

- Make sure to avoid the vicinity of any source of interference such as computer screens, TV sets or solid metal objects. Within solid walls, especially ones with metal parts, the transmission range (max. 100 m) can be reduced considerably.

8. Battery replacement

- As soon as the corresponding battery symbol appears in the display, please change the batteries of the base station or transmitter

- Please note: When the batteries are changed, the contact between the outdoor transmitter and the base station must be restored – so always restart both devices or start a manual transmitter search.

9. Additional outdoor transmitters (optional)

• When having more than one external transmitter, select a different channel for each one with the 1/2/3 switch inside the transmitter's battery compartment. Insert two new AA 1.5 V batteries, polarity as illustrated. Start the base station operation or the manual search for the outdoor transmitter:
• Choose the respective transmitter by pressing the +/CHANNEL button.
• Press and hold the + / CHANNEL button for three seconds. The last registered transmitter (channel) will be cancelled.
• Press the TX button in the corresponding transmitter's battery compartment. The transmission of the outdoor data will take place immediately.
• The outdoor temperature and the channel number will be shown on the base station display. If you have installed more than one outdoor transmitter, press the + / CHANNEL button on the base station to change between the channels 1 to 3.
• You can also choose an alternating channel display. Press the + / CHANNEL button. After the last registered channel (1 to 3) a circle symbol will appear. To deactivate the function, press the + / CHANNEL button again.
• Press the SET/MAX/MIN button several times to view the maximum and minimum values of the currently selected channel.
• After a successful installation close the outdoor transmitter's battery compartment carefully.

Wireless Thermometer

10. Troubleshooting

Problem Solution

No indication on the → Ensure the batteries' polaribase station or the ties are correct transmitter → Change the batteries

No transmitter → No outdoor transmitter is reception installed

Display “- -.-” → Start manual search for the outdoor transmit

→ Check the outdoor transmitter's batteries (only use batteries/rechargeable batteries with 1.5V voltage!)
→ Restart the outdoor transmitter and the base station according to the manual
→ Choose another place for the transmitter and/or the base station
→ Reduce the distance between the transmitter and the base station
→ Check if there is any source of interference

No DCF reception → Activate (ON) the DCF reception in set

→ Wait for an attempt reception during the night
→ Change the location (interference!)
→ Restart the device according to the manual
→ Set the clock manually

Incorrect indication → Change the batteries

If your device fails to work despite these measures, please contact the retailer where you purchased the product from for advice.

11. Waste disposal

This product and its packaging have been manufactured using high-grade materials and components which can be recycled and reused.

Wireless Thermometer

This reduces waste and protects the environment. Dispose of the packaging in an environmentally friendly manner using the collection systems that have been set up.

Disposal of the electrical device

Remove non-permanently installed batteries and rechargeable batteries from the device and dispose of them separately.

This product is labelled in accordance with the EU Waste Electrical and Electronic Equipment Directive (WEEE).

This product must not be disposed of in ordinary household waste. As a consumer, you are required to take end-of-life devices to a designated collection point for the disposal of electrical and electronic equipment, in order to ensure environmentally-compatible disposal. The return service is free of charge. Observe the current regulations in place!

Disposal of the batteries

Never dispose of empty batteries and rechargeable batteries with ordinary household waste. They contain pollutants which, if improperly disposed of, can harm the environment and human health. As a consumer, you are required by law to take them to your retail store or to an appropriate collection site depending on national or local regulations in order to protect the environment. The return service is free of charge.

The symbols for the contained heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead.

1. Specifications

Base station

Power consumption 2 x AA 1,5 V batteries (not included)

Measuring range temperature 0°C ... 50°C

Resolution 0.1°C

Wireless Thermometer

Accuracy ±1°C

Housing dimension 69 x 30 (49) x 155 mm

Weight 112 g (device only)

Outdoor transmitter

Power consumption 2 x AA 1,5 V batteries (not included)

We recommend Alkaline batteries

Measuring range temperature -40°C ...60°C

Resolution: 0.1°C

Accuracy ±1 °C @ 0... 50 °C, otherwise ±1.5°C

Range max. 100 m (open field)

Transmission frequency 433 MHz

Maximum

radio-frequency power < 10mW

Housing dimension 48 (54) x 26 (44) x 129 (135) mm

Weight 62 g (device only)

No part of this manual may be reproduced without written consent of TFA Dostmann. The technical data are correct at the time of going to print and may change without prior notice. The latest technical data and information about this product can be found in our homepage by simply entering the product number in the search box.

EU Declaration of conformity

Hereby, TFA Dostmann declares that the radio equipment type 30.3072 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

www.tfa-dostmann.de/service/downloads/ce

www.tfa-dostmann.de