PerfectView M 55LX AHD - Monitor DOMETIC - Free user manual and instructions

Product type	TFT color LCD monitor
Brand	Dometic
Model	PerfectView M 55LX AHD
Screen size	5 inches (12.7 cm)
Dimensions (W x H x D)	146 x 87 x 26 mm
Weight	350 g
Power supply	12 - 30 V=
Power	Maximum 10 W
Resolution	384,000 pixels
TV standard	1080p30/25, 720p30/25, PAL, NTSC (automatic switching)
Brightness	Approx. 350 cd/m²
Operating temperature	-20 °C to 70 °C
Storage temperature	-30 °C to 70 °C
Maximum humidity	85 %
Vibration resistance	6 g
Number of supported cameras	Up to 4
Main functions	Automatic camera switching, brightness/contrast/color/volume adjustment, auto-dimmer, adjustable distance marks, mirror mode, auto search, trailer detection
Maintenance	Clean with a damp cloth; do not use sharp or hard objects.
Safety	Secure mounting outside airbag area; do not use with wet hands; follow assembly and wiring instructions.
Included accessories	Monitor, bracket, cover, connection cable, mounting hardware
Optional accessories	Sun visor (ref. 9102200200)
Certifications	E13

Frequently Asked Questions - PerfectView M 55LX AHD DOMETIC

How to turn on the screen?

Press the Ⓞ key (fig. 10, item 2) to turn on the screen. The key lights up green.

How to adjust the screen brightness?

Press the menu key (fig. 10, item 5) until Brightness is displayed. Use the + and - keys to adjust the value from 0 to 100.

How to use the automatic camera search?

Go to the Auto search menu via the menu key, then activate it with +. The screen will automatically cycle through connected cameras with an adjustable interval (2 to 20 s).

How to adjust the distance marks?

In the menu, select Scale. Use + and - to shift the marks or select the next one. Press menu to finish.

What to do if the screen does not turn on?

Check the supply voltage (12-30 V=) and the connections of the red (terminal 15) and black (ground) cables. Ensure the fuse has not blown. Refer to the manual for the wiring diagram.

Can non-AHD cameras be used with this monitor?

Yes, the monitor accepts PAL and NTSC signals in addition to AHD signals. It switches automatically.

How to mount the screen in a vehicle?

Attach the screen bracket with the provided self-tapping screws, then place the screen and tighten the thumbscrew. Ensure it does not obstruct driving and is outside the airbag zone. Refer to the manual for detailed steps.

How to clean the screen properly?

Disconnect the power cables. Clean only with a damp cloth. Do not use sharp or hard objects to avoid damaging the screen.

What is the required supply voltage?

The operating voltage is 12 to 30 V=. Observe polarity to avoid damage.

Where to find the complete manual for the PerfectView M 55LX AHD?

The complete 248-page manual is available for free download in PDF format on the notice-facile.com website. You can also ask questions about the device there.

USER MANUAL PerfectView M 55LX AHD DOMETIC

Please read this instruction manual carefully before installation and first use, and store it in a safe place. If you pass on the product to another person, hand over this instruction manual along with it.

Table of contents

1 Explanation of symbols. 9 2 Safety and installation instructions 10 3 Scope of delivery 12 4 Accessories. 12 5 Intended use 13 6 Technical description 13 7 Installing the LCD monitor 15 8 Using the LCD monitor. 18 9 Cleaning and caring for the LCD monitor 21 10 Warranty 21 11 Disposal. 21 12 Technical data 21

1 Explanation of symbols

CAUTION!

Safety instruction: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.

NOTICE!

Indicates a situation that, if not avoided, can result in property damage.

NOTE

Supplementary information for operating the product.

2 Safety and installation instructions

Please observe the safety instructions and stipulations issued by the vehicle manufacturer and service workshops.

The manufacturer accepts no liability for damage in the following cases:

• Faulty assembly or connection
• Damage to the product resulting from mechanical influences and incorrect connection voltage
• Alterations to the product without express permission from the manufacturer
• Use for purposes other than those described in the operating manual

NOTICE! Beware of damage

• To prevent the risk of short circuits, always disconnect the negative terminal of the vehicle's electrical system before working on it. If the vehicle has an additional battery, its negative terminal should also be disconnected.
• Inadequate supply cable connections could result in short circuits, causing:
• Cable fires
• The airbag being triggered
• Damage to electronic control equipment
• Electrical malfunctions (indicators, brake light, horn, ignition, lights)

Therefore, please observe the following instructions:

• When working on the following cables, only use insulated cable terminals, plugs and flat sockets:
• 30 (direct supply from positive battery terminal)
• 15 (connected positive terminal, behind the battery)
• 31 (return cable from the battery, earth)
• 58 (reversing light)

Do not use porcelain wire connectors.

• Use a crimping tool (fig. 1 12, page 3) to connect the cables.
• Screw the cable when connecting cable 31 (earth)
• Screw on the cable using a cable terminal and serrated washer to one of the vehicle's earth bolts or
• Screw the cable to the bodywork using a cable terminal and a self-tapping screw

Make sure there is a good earth connection.

If you disconnect the negative terminal of the battery, all data stored in the volatile memories will be lost.

• The following data must be reset, depending on the vehicle equipment options:
• Radio code
• Vehicle clock
• Timer
• On-board computer
• Seat position

You can find instructions for making these settings in the operating manual.

Observe the following installation instructions:

CAUTION!

• Secure the monitor in such a way that it cannot become loose under any circumstances (sudden braking, accidents) and cause injuries to the occupants of the vehicle.
• Do not attach the monitor in the air bag deployment path, as this could cause injury if the airbags are triggered.

Observe the following instructions when working with electrical parts:

• When testing the voltage in electrical cables, only use a diode test lamp (fig. 1 1, page 3) or a voltmeter (fig. 2, page 3). Test lamps with a bulb (fig. 1 3, page 3) consume voltages which are too high and can damage the vehicle's electronic system.
• When routing the electrical connections, ensure that:
• They are not kinked or twisted
• They do not rub on edges
• They are not laid in sharp-edged ducts without protection (fig. 3, page 4).

Insulate all connections. - Secure the cables against mechanical wear by using cable binders or insulating tape, for example on existing cables.

Observe the following instructions when handling the LCD monitor:

CAUTION!

• People (including children) whose physical, sensory or mental capacities or whose lack of experience or knowledge prevent them from using this product safely should not use it without the supervision or instruction of a responsible person.
• Do not open the monitor (fig. 4, page 4).
• Do not submerge the monitor in water (fig. 5, page 4); the monitor is not waterproof.
• The monitor must not impair your vision when driving (fig. 8, page 5).
• Do not operate the monitor with wet hands.
• Do not operate the monitor if the housing has been damaged.

NOTICE!

• Connect it to the correct voltage.
• Do not use the monitor in areas which
• are subjected to direct sunlight,
• are subject to strong temperature fluctuations, have high levels of humidity,
• are poorly ventilated,
• are dusty or oily.
• Do not press against the LCD display.
• Do not drop the monitor.
• If you use the monitor in vehicles, the vehicle should be running during operation to prevent the vehicle battery from discharging.
• The picture quality can be impaired in the vicinity of electromagnetic fields.

For this reason do not mount the monitor near loudspeakers.

No. in

fig. 9,

Quantity Description

Ref. no.

M55LXAHD M75LXAHD

11 Monitor 9600012883

9600012899

2 1 Monitor bracket

9102200193

3 1 Monitor bracket cover

• 1 Connection cable

9102200196

Fastening material

4 Accessories

Available as accessories (not included in the scope of delivery):

Description	Ref. no.
Sun visor for M55LX AHD	9102200200
Sun visor for M75LX AHD	9102200201

The LCD monitors PerfectView M55LX AHD and M75LX AHD are monitors which are primarily intended for use in vehicles. They can be used together with cameras (e.g. a reversing video system) or other video sources.

The LCD monitors are designed for use in all vehicles.

The LCD monitors are designed for commercial use.

6 Technical description

6.1 Function description

The LCD monitor can be connected to cameras (e.g., reversing video systems) or other video sources (e.g., DVD players). It is possible to switch back and forth between video sources.

The monitor features control cables that allow the cameras to be activated automatically.

It can operate up to four cameras. Alongside the usual controls, the four cameras can be switched consecutively in automatic mode. This monitor also features a distance indicator in the display that is activated automatically when the reverse gear is engaged (CAM1).

6.2 Control elements

The following control elements are located on the monitor:

No. in fig. 10, page 6	Descrip- tion	Description
1 Sensor window for the dimmer function. The brightness of the display is automatically adapted to the ambient light.
2 Switches the monitor on and off. The button lights up red when the monitor is in standby. It lights up green when the monitor is switched on.
3 + 1. Increases the brightness. 2. Increases the value of the selected parameter if a menu is opened.
4-	1. Reduces the brightness. 2. Reduces the value of the selected parameter if a menu is opened.

No. in fig. 10, page 6	Descrip- tion	Description
5	≡	1	.	S
		2. Calls up the parameters for setting.
		The parameters are distributed over four screen pages in the following order:
		Page 1: Picture
		- B r i g h t n e s s
		- C o n t r a s t
		- C o l o u r
		- V o l u m e
		- A u t o D i m
		- Distance: Distance marker setting
		Page 2: Options
		- Language: German, English, French, Italian, Dutch, Spanish, Portuguese, Russian
		- Scale: switches the distance markers on or off
		- Camera 1/Camera 2/Camera 3/Camera 4: Normal or Mirrored
		- Sensitivity: Setting of the switching threshold for the night dimmer function
		- Trailer detection ON/OFF: Shortens the activation time in OFF mode
		Page 3: Auto search
		- Automatic search Switches the automatic camera panning on (the cameras are activated in preset time intervals, e.g. for horse transporters with multi-box monitoring).
		- Camera 1/Camera 2/Camera 3/Camera 4: Setting for the switching intervals
		- Reset ("Default"): Default setting for all parameters
6 CAM Switches from one camera to the next.
7	M	o	n	i
8 Loudspeaker

7 Installing the LCD monitor

7.1 Tools required (fig. 1, page 3)

For installation and assembly you will need the following tools:

• Measuring ruler (4)
• Centre punch (5) Hammer (6)
• Drill head set (7)
• Drill (8) Screwdriver (9)

To establish and test the electrical connection, the following tools are required:

• Diode test lamp (1) or voltmeter (2) Insulating tape (10)
• Heat shrinking sleeve Hot air blower (11) Crimping tool (12)
• Soldering iron (optional) (13)
• Solder (optional) (14)
• Cable bushing sleeves (optional)

To fasten the cables, you may require additional cable binders.

7.2 Installing the monitor

CAUTION! Beware of injury

Select the location of the monitor so that it cannot injure the passengers in the vehicle under any circumstances (e.g. sudden braking, road traffic accidents).

Observe the following installation instructions:

• Select an installation location that provides an unobstructed view of the monitor (fig. 6 and fig. 7, page 4).
• Never install the monitor in areas where your head could hit it or in the airbag deployment path. This could cause injury if the airbag opens.
• The monitor must not impair your vision when driving (fig. 8, page 5).
• The installation location should be flat.
• Check that there is sufficient space underneath the installation location to attach the washers and nuts.
• Check beforehand that there is sufficient space on the other side for the drill head to come out (fig. 2, page 4).
• Bear in mind the weight of the monitor. Provide reinforcement if necessary (larger washers or plates).
• Make sure you can lay the connection cable to the monitor.

Choosing the installation location (fig. 11, page 7)

Place the monitor on the monitor bracket. Position the monitor and the attached monitor bracket provisionally.

Mark the outlines of the corners of the support base on the dashboard. Take the monitor off the monitor bracket.

Screwing the monitor bracket onto the dashboard (fig. 12, page 7)

Hold the support base within the outlines marked beforehand. Fasten the monitor bracket with the self-tapping screws.

Fastening the monitor

Set the monitor on the monitor bracket and secure it with the knurled nut (fig. 11, page 7). ▶ Slide the cover over the monitor bracket on the monitor.

7.3 Connecting the monitor electrically

The circuit diagram for the LCD monitor can be found in fig. 14, page 8:

No. Description
1	M	o	n	i	t	o
2	2	0	-	p	i	n
3 Monitor line
4 20-pin plug
5	12 - 24 V positive cable (red): connected to the positive pole of the ignition (connected positive, terminal 5) or the positive pole of the battery (terminal 30).
6 Earth cable (black): connected to the negative pole of the voltage source.
7 Cable (green): control input for video input CAM1, such as for connecting the reversing light
8 Cable (white): control input for video input CAM2, such as for the side camera
9 6-pin CAM1 socket (connection to video source 1)
10 6-pin CAM2 socket (connection to video source 2)

No. Description

11 6-pin CAM3 socket (connection to video source 3) with video signal detection 12 6-pin CAM4 socket (connection to video source 4), with video signal detection) 13 Cable (blue): control input for video input CAM3 If the system is activated via this control line, none of the buttons have a function (according to DIN EN 1501-1).

NOTICE!

Cables and connections that are not properly installed will cause malfunctions or damage to components.

Correct installation of cables and connections ensures lasting and trouble-free operation of the retrofitted components.

Observe the following instructions when laying the connection cable:

• If possible, use original ducts for laying the cables, or other suitable options, such as ventilation grilles. If there are no existing ducts, you must drill a hole of ø 22 mm. Check beforehand that there is sufficient space on the other side for the drill head to emerge (fig. 2, page 4).
• Cover the holes with the feed through (fig. 12 1, page 7) in the base of the monitor bracket.
• To prevent damage to the cables, when laying them ensure that there is always sufficient distance to vehicle components which can become hot (lights, heaters, ventilators etc.).
• When laying the cables (fig. 3, page 4), make sure:
• They are not kinked or twisted
• They do not rub on edges
• They are not laid in sharp-edged ducts without protection.

Connecting the monitor as a reversing video system (fig. 14, page 8)

Lay the connection cable for the monitor bracket on the dashboard. Insert the plug of the monitor cable (2) into the socket (4) of the connection cable (3).

Wait until you hear the plug snap in.

NOTICE! Beware of damage

Make sure the polarity is correct when connecting to a voltage source.

Connect the red and black cables of the connection cable to a suitable voltage supply: - Connect the red cable (5) to terminal 15 (ignition). - Connect the black cable (6) to terminal 31 (earth). If the monitor is to be activated when reverse gear is selected, connect the green cable (7) to the positive cable of the reversing light.

NOTE

If voltage is present in the green cable (7), the reversing camera will be activated automatically. The reversing camera has priority.

If the monitor is to be activated e.g. when the indicator is flashing, connect the following control cable to a positive cable of the indicator:

• white cable (8), blue cable (13)

NOTE

If voltage is present in this control cable, the video input CAM2 and CAM3 will be activated.

This control cable is used as a signal cable for the activation of a side camera when an indicator is flashing, for example.

If necessary, connect the CAM1 socket (9) of the connection cable to the plug of video source 1 (e.g. reversing camera). If necessary, connect the CAM2 socket (10) of the connection cable to the plug of the video source 2 (e.g. side camera). If necessary, connect the CAM3 socket (11) of the connection cable to the plug of video source 3 (e.g. camera).

NOTE

Observe the power consumption of the video system. The cameras are equipped with heaters. A maximum current of 1.5 A can flow (three cameras in heating mode). Use a disconnector switch for direct connection to the battery. This allows you to disconnect the video system from the battery easily if you are no longer using the vehicle.

Connecting an additional reversing camera (trailer operation)

If necessary, connect socket CAM4 (12) of the connection cable to the plug of the additional reversing camera.

8 Using the LCD monitor

8.1 Switching on the monitor

If the monitor is switched off, press the button (fig. 10 2, page 6) to switch the monitor on. The button lights up green. The picture appears.

8.2 Switching off the monitor

Press the button (fig. 10 2, page 6) to switch off the monitor. The button lights up red. The picture disappears.

8.3 Setting the monitor

To set the monitor to suit your requirements, proceed as follows (fig. 10, page 6):

Press the button (5) to call up the required parameter. The parameters to be set appear in the following order:

Page 1: Picture

- Brightness: 0-100 - Contrast: 0-100 - Colour: 0-100 - Volume: 0-100 - Auto Dim On, Off - Distance: distance marker setting (chapter "Setting the distance markers" on page 20)

Page 2: Options

• Language: German, English, French, Italian, Dutch, Spanish, Portuguese, Russian
• Scale: On, Off

(switches the distance markers on or off)

• Camera 1/Camera 2/Camera 3/Camera 4: Normal or Mirrored Sensitivity: 1, 2

Setting of the switching threshold for the night dimmer function to avoid glare.

In dimming mode, the switching threshold can be set at two levels.

• Trailer detection ON/OFF: Shortens the activation time in OFF mode

Page 3: Auto search

• Automatic search: On, Off

Switches the automatic camera panning on (the cameras are activated in preset time intervals, e.g. for horse transporters with multi-box monitoring).

• Camera Delay: Setting of the delay intervals (2 to 20 s)
• Default: Default setting for all parameters

Press the "+" button (3) or the "-" button (4) to set the required parameter. Press the "+" button (3) to increase the value of the selected parameter. Press the "-" button (4) to reduce the value of the selected parameter.

8.4 Setting the video source

Proceed as follows to set the video source (fig. 10, page 6):

If you want to switch to a different video source, press the "CAM" button (6). The monitor changes the camera in the order "Camera 1 - Camera 2 - Camera 3 - Camera 4".

NOTE

If you want the cameras to run automatically: see chapter "Setting the automatic search" on page 20.

8.5 Setting the automatic search

Proceed as follows to set the automatic search (fig. 10, page 6):

Press the "≡" button (5) until the "Auto search" menu appears. Press the "+" button (3) to switch on the automatic search. The monitor starts the cameras in the order "Camera 1 - Camera 2 - Camera 3 - Camera 4" automatically in the preset time.

After the first run through, only the inputs with connected cameras are shown.

No sound is available in this operating mode.

Setting the display time

You can set the display time from 2 to 20 seconds.

Press the "≡" button (5) until the "Cam Delay" menu appears. Press the "+" button (3) to increase the camera display time.

Press the "-" button (4) to reduce the camera display time.

Quitting the automatic search

Press the "≡" button (5) until the "Auto search" menu appears. Press the "+" button (3) to switch off the automatic search.

8.6 Detecting the trailer camera

This function is required when using a trailer camera (fig. 13, page 7) if the system is activated automatically via the reverse gear. To initialise the automatic detection, switch off ignition once.

• One camera connected (e.g. towing vehicle without a trailer):

the camera connected to CAM1 (1) is activated.

• Two cameras connected (e.g. towing vehicle with a trailer):

the camera connected to CAM4 (2) is activated (CAM1 is inactive).

8.7 Setting the distance markers

To set the distance markers, proceed as follows (fig. 10, page 6):

Press the "≡" button (5) until the "Scale" menu appears. The distance markers to be set appear. Press the "+" button (3) to move the red highlighted distance markers. Press the "-" button (4) to select the next distance marker. Press the "≡" button (5) to exit the settings.

9 Cleaning and caring for the LCD monitor

NOTICE! Beware of damage

• Do not use sharp or hard objects for cleaning, as these may damage the monitor.
• Remove the cable before cleaning the monitor to prevent short circuiting.

Clean the monitor with a soft, damp cloth from time to time.

10 Warranty

The statutory warranty period applies. If the product is defective, please contact the manufacturer's branch in your country (see the back of the instruction manual for the addresses) or your retailer.

For repair and warranty processing, please send the following items:

Defect components - A copy of the receipt with purchasing date - A reason for the claim or description of the fault

11 Disposal

Place the packaging material in the appropriate recycling waste bins wherever possible.

If you wish to finally dispose of the product, ask your local recycling centre or specialist dealer for details about how to do this in accordance with the applicable disposal regulations.

12 Technical data

	M55LX AHD M75LX	AHD
Ref. no.: 9600012883 9600012899
Type: Colour TFT LCD
Display size: 5" (12.7 cm) 7" (17.8 cm)
Brightness: approx. 350 cd/m2	approx. 800 cd/m2
Display resolution:	384,000 pixels	>600,000 pixels
Video standard:	1080p30 / 1080p25 / 720p30 / 720p25 / PAL / NTSC (automatic switching)
Operating voltage:	12 - 30 V==
Power:	max. 10 W
Operating temperature:	-20 °C to 70 °C
Storage temperature:	-30 °C to 70 °C
Humidity: max. 85%
Vibration resistance: 6 g
Dimensions in mm W x H x D:	146 x 87 x 26	190 x 110 x 26
Weight: 350 g 400 g

Approvals

The device has E13 certification.

6 Technical description

Do not use terminal blocks.

• For the connection cable, use crimp connectors (Fig. 1 12, page 3).
• Connect the cable to the wire 31 (housing)
• with the cable clamp or toothed spring washer to the screw for connection to the housing, which is on the vehicle, or with the cable clamp and self-tapping screw to the body sheet metal.

Connect the device properly to the housing!

When disconnecting the negative terminal of the battery, all volatile memory devices of the gate control electronics lose their stored data.

Depending on the equipment, you will need to reconfigure the following data:

6.1 Description of operation

The monitor is a monitor to which cameras (e.g., rear view camera system) or other video sources (e.g., DVD player) can be connected. Switching between video sources is possible.

The monitor offers control lines that can be used to automatically activate the cameras.

The monitor can work with four cameras. In addition to manual control, the four cameras can be switched automatically one after the other. The monitor also has a distance indicator on the rear, which is automatically activated when reverse gear is engaged (CAM1).

The monitor display can be protected from the sun with a sun visor.

6.2 Control elements

The monitor has the following control elements:

7 Installation of the monitor

7.1 Required tools (Fig. 1, page 3)

For installation, the following tools are required:

- Ruler (4) - Center punch (5) - Hammer (6) - Screwdriver set (7) - Drill (8) - Saw (9)

For further use and checking, the following auxiliary means are required:

• Bottom control lamp (1) and voltmeter (2)
• Insulation tape (10) heat-shrink tubing
• Industrial (11)
• Crimping pliers (12) - Under certain circumstances, pliers (13) - Under certain circumstances, soldering iron (14)
• If necessary, cable feed-throughs

For cable fastening, cable ties may also be required.

7.2 Monitor mounting

CAUTION! Risk of injury!

Choose the mounting method for the monitor so that under no conditions (e.g., sudden braking, accident) does a risk of injury to passengers arise.

When mounting, observe the following instructions:

• Choose a suitable mounting location that ensures an unobstructed view of the monitor (Fig. 6 and Fig. 7, p. 4). Do not mount the monitor in the head impact zone or within the deployment range of the airbags. Otherwise, there is a risk of injury in the event of an accident.
• The monitor must not restrict visibility when driving the vehicle (Fig. 8, p. 5).
• The mounting location must be flat.
• Make sure that there is sufficient free space behind the chosen mounting location for the installation of bolts and nuts.
• Preliminarily check whether there is enough free space for the drill bit to exit (Fig. 2, p. 4).
• Remove the monitor. If necessary, provide reinforcement (larger mounting plates).
• Make sure that the cable can be routed to the monitor.

Determine the mounting location (Fig. 11, page 7).

Install the monitor on the bracket.

For the monitor to be placed on the bracket, mark the outline of the bracket base on the instrument panel. Remove the monitor from the bracket.

Attaching the monitor bracket to the instrument panel (Fig. 12, page 7).

Place the bracket support within the previously marked outlines. Secure the monitor bracket with self-tapping screws.

Monitor mounting.

Install the monitor on the bracket and secure it with the nut and washer (Fig. 11, page 7). Put the cover over the bracket on the monitor.

7.3 Electrical connection of the monitor.

The connection diagram for the monitor is shown in Fig. 14, page 8.

№ HaIMeHOBaHne
1 MoHITop
2 20-koHT. pa3bem
3 Пиня пITAня мОнITopa
4 20-koHT. shTekep
5	Полохителовий кабел 12 - 24В (кpacnbий):princocoindenenne К ралохитelbHOMу пOLUCу сИстемы 3axngarHnry (ВКПЮчЕнь «ППOC», ЗжIM 15) ип K ралохитelbHOMу пOLUCу 6aTapeи (ЗжIM 30)
6 Ka6eIb дЯ coeDINHeHЯс корпсOM (черны):princocoindenenne К оtrPицatelbHOMу пOLUCу ИСТочнka habржeHЯ
7 Ka6eIb (ЗeLEнь):вхOD сИнану упраВлe"HЯ дя вideobxOda CAM1, Наример, дя princocoindenenne K φаре 3aДнeroхда
8 Ka6eIb (бeль):вхOD сИнану упраВлe"HЯ дя вideobxOda CAM2, Наример, bokoboi Камеры
9 6-koHT. pa3bem CAM1 (princocoindenenne K ИСТочнky вideocinHaа 1)
10 6-koHT. pa3bem CAM2 (princocoindenenne K ИСТочнky вideocinHaа 2)
11 6-koHT. pa3bem CAM3 (princocoindenenne K ИСТочнky вideocinHaа 3) c paCNo3HabAHm E M BideocinHaа
12 6-koHT. pa3bem CAM4 (princocoindenenne K ИСТочнky вideocinHaа 4, c paCNo3HabAHm E M BideocinHaа)
13 Ka6eIb (сiни):вхOD сИнану упраВлe"Hя dя вideobxOda CAM3 Еси сИstema akTIBNpyETcЯ老人家 yypNKuzn (coIpaCHO DIN EN 1501-1).

WARNING!

Incorrect routing and connection of cables can lead to permanent failures and damage to parts.

Proper routing and connection of cables is the main condition for reliable, trouble-free operation of the installed components.

When routing the connecting cables, follow the following instructions:

• For through-wall installation, there must be no possibility of routing the cables through existing openings, for example, ventilation grilles. If there are no through openings, it is necessary to drill a 22 mm hole. First, check that there is enough free space for the drill to exit (Fig. 2, p. 4).

Close the hole with the grommet (Fig. 12 1, p. 7) on the monitor mounting plate. To avoid cable damage, always maintain sufficient distance from hot vehicle components (lights, heater, ventilation, etc.) when routing cables. - When routing cables (Fig. 3, p. 4), make sure that they are not pinched.

-Do not bend or kink them, -Do not route them over sharp edges, -Do not route them without protection through openings with sharp edges.

Connect the monitor as a rear view camera system (Fig. 14, p. 8)

Connect the monitor's connection cable to the device panel. Insert the monitor cable plug (2) into the socket (4) of the connection cable (3).

It should click into place with a characteristic sound.

CAUTION! Risk of damage!

9 Care and cleaning of the LCD monitor

CAUTION! Risk of damage!

dometic.com/sales-offices