EMW8545GW - Washing machine EAS Electric - Free user manual and instructions
Find the device manual for free EMW8545GW EAS Electric in PDF.
Download the instructions for your Washing machine in PDF format for free! Find your manual EMW8545GW - EAS Electric and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. EMW8545GW by EAS Electric.
USER MANUAL EMW8545GW EAS Electric
V.2For your safety,the information in this manual must be followed to minimize the risk of fire or explosion, elec- tric shock, or to prevent property damage, personal injury or loss of life. Explanation of the symbols: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. The new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused. Before any maintenance the device, unplug the appliance from the mains. Electric shock! SAFETY INSTRUCTIONS Important safety instructions This combinatio n of symbol and signal word indi- cates a potentially dangerous situation which may result
Warning! This combination of symbol and signal word indicates a potentially dangerous situation which may result in slight or minor injuries. Note! This combination of symbol and signal word indicates a potentially dangerous situation which may result in slight or minor injuries or damage to property and the environment. Caution!
V.2 Always unplug the machine and turn off the water supply after use. The max. inlet water pressure, in pascals. The min. inlet water pressure, in pascals. To ensure your safety, power plug must be inser- ted into an earthed three-pole socket. Check carefully and make sure that your socket is properly and reliably earthed. Make sure that the water and electrical devices must be connected by a qualified technician in accordance with the manufacturer's instructions and local safety regulations. Pull out its plug from the power socket before cleaning or maintenance. Do not use any socket with rated current less than that of appliance. Never pull out power plug with wet hand. Please remember to disconnect water and power supply immediately after the clothes are washed. Risk to children! EN countries: the appliance can be used by chil- dren aged from 8 years and above and persons with reduced physical, sensory or mental capabi- lities or lack of experience and knowledge if they have been given supervision or instruction concer- ning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Children of less than 3years should be supervised to ensure that they do not play with appliance. Animals and children may climb into the machine. Check the machine before every operation. Kids should be supervised that they do not play with the appliance. SAFETY INSTRUCTIONS
s door may be very hot during the operation.
ep kids and pets far away from the machine during the operation very wet rooms as well as in the rooms with explosive or caustic gas. Remove all packages and transport bolts before using the appliance.
erious damage may result. Risk of explosion! Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combus- tible or explosive substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kero- sene, etc.) This may result in fire or explosion. The washer dryer is not to be used if industrial chemicals have been used for cleaning. The exhaust air must not be discharged into a flue which is for exhausting fumes from appliances burning gas or other fuels. Before hand thoroughly rinse items of washing by hand. Installing the product! This appliance is for indoor use only. It isn't intended to be built-in using. The openings must not be obstructed by a carpet. The appliance shall not be installed in bath room or very wet rooms as well as in the rooms with explosive or caustic gases. The appliance with single inlet valve only can be connected to the cold water supply. The appliance with double inlet valves should be correctly connected to the hot water and cold water supply. SAFETY INSTRUCTIONS Caution!
V.2 Plug must be accessible after installation. The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the washer dryer. The appliance shall not be installed at a humid place. Remove all packages and transport bolts before using the appliance. Otherwise, serious damage may result. Risk of damaging appliance! The product is only for home use and is only designed for the textiles suitable for machine washing and drying. Do not climb up and sit on top cover of the machine. Do not lean against machine door. Cautions during Handling Machine: Transport bolts shall be reinstalled to the ma- chine by a specialized person. The accumulated water shall be drained out of the machine. Handle the machine carefully. Never hold each protruded part on the machine while lifting. Machine door cannot be used as the handle during the conveyance. This appliance is heavy. Transport with care. Hands shall not be inserted into running water extracting tub. Please do not close the door with excessive forces. If it is found difficult to close the door, please check if the clothes are put in or distributed well. It is forbidden to wash carpets. SAFETY INSTRUCTIONS
V.2 Before using the wash machine, the product shall be calibrated. Before washing the clothes at first time, the product shall be operated in one round of the whole procedures without the clothes inside. Flammable and explosive or toxic solvents are forbidden. Gasoline and alcohol etc.Shall not be used as detergents. Please only select the detergents suitable for machine washing, especially for drum. Make sure that all pockets are emptied. Sharp and rigid items such as coin,brooch,nail,screw or stone etc. may cause serious damages to this machine. Please check whether the water inside the drum has been drained before opening its door. Please do not open he door if there is any water visible. Be careful of burning when the product drains hot washing water. After the program is completed, Please wait for two minutes to open the door(Some model). Never refill the water by hand during washing. If it is unavoidable that fabrics that contain vege- table or cooking oil or have been contaminated by hair care products. it be placed in a tumble dryer they should first be washed in hot water with extra detergent, this will reduce, but not eliminate, the hazard. Adequate ventilation has to be provided to avoid the back flow of gases into the room from appliances burning other fuels, including open fires. SAFETY INSTRUCTIONS Operating the appliance!
V.2 Fabric softeners, or similar products, should be used as specified by the fabric softener instructions. The machine whose lid can be opended during water extraction, that it takes 15s or more for complete stop of water extracting chamber tub. Remove all objects from pockets such as ligh- ters and matches before use the appliance. SAFETY INSTRUCTIONS DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such waste separately for special treatment is necessary. The european directive 2012/19 /UE on wasted electrical and electronic equipments (WEEE), requires that household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you disposed of the appliances, it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.
V.2INSTALLATION Accessories Product Description Transport hole plug Supply hose cold water
- The product line chart is for reference only, please refer to real product as standard. Note! Drum Control panel Power supply cord Detergent dispenser Service filter Door Water supply hose Top cover Drain hose Owner’s manual
V.2INSTALLATION Installation Before installing the machine, the location characterized as follows shall be selected: 1.Rigid, dry, and level surface 2.Avoid direct sunlight 3.Sufficient ventilation 4.Room temperature is above 0°C 5.Keep far away from the heat resources such as coal or gas. Unpacking the washing machine 1.Remove the cardboard box and styrofoam packing. 2.Lift the washing machine and remove the base packing. Make sure the small triangle foam is removed with the bottom one together. If not, lay the unit down with side surface, then remove the small foam from the unit bottom manually. 3.Remove the tape securing the power supply cord and drain hose. 4.Remove the inlet hose from the drum. Stability is important to prevent the product from wandering! Make sure that the product should not stand on the power cord.
Warning! Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk of suffocation! Keep all packaging well away from children.
W> 20mm Installation area
V.2INSTALLATION Remove transport bolts You must remove the transport bolts from the backside before using the product.
Warning! Loosen the 4 transport bolts with a spanner. Remove the bolts including the rubber parts and keep them for future use. Close the holes using the cover caps. Levelling the washing machine The lock nuts on all four feet must be screwed tightly against the housing.
Warning! 1.Loosen the lock nut. 2.Turn the foot until it reaches the floor. 3.Adjust the legs and lock the nuts with a spanner. Make sure the machine is level and steady. Connect the water supply hose To prevent leakage or water damage, follow the instructions in this chapter.Do not kink, crush or modify water inlet hose.
Warning! Connect the water supply hose to the water inlet valve and a water tap with cold water as indicated. Connect manually, do not use tools. Check if the connections are tight. Note!
V.2INSTALLATION Drain Hose There are two ways to place the end of drain hose: 1.Put it into the water trough. 2.Connect it to the branch drain pipe of the trough. Do not kink or protract the drain hose. Position drain hose properly, otherwise damage might result of water leakage. Water trough Min.60cmMax.100cm
- Detergent need to be added in "case I “after selecting pre-washing for machines with this function.
Note! Caution! OPERATIONS Main wash PrewashSoftenerIt’s recommend to calibrate the wash machine so that can serve you better.1-Empty the wash machine;2-Plug in; 3-Power on the wash machine and press “Temp.” and “Función” at the same time within 10 seconds then display “t19”4- Press to start the washing machine until the figurescorresponding to the calibration of your washing machine are displayed.
- Before washing, please make sure it’s installed properly.
- Before washing at first time, the washing machine shall be operated in one round of the whole procedures without clothes in as follows. Calibration Select Programme
- When washing a single clothes, it may easily cause great eccentricity and give alarm due to great unbalance. Therefore it is suggested to add one or two more clothes to be washed together so that draining can be done smoothly.
- Don’t washing the clothes touching with kerosene, gasoline, alcohol and other flammable materials.
- The working condition of the washer should be(0-40)°C. If used under 0°C, the inlet valve and draining system may be damaged. If the machine is placed under condition of 0°C or less, then it should be transferred to normal ambient tem- perature to ensure the water supply hose and drain hose are not frozen before use.
- Please check the labels and the explanation of using detergent before wash. Use non-foaming or less-foaming detergent suitable for machine washing properly. Take out the items out of the pockets Put small clothes into the pillow slip Check the label Before Each Washing Turn easy-pilling and long-pile fabric inside out Separate clothes with different textures
Warning! OPERATIONS 3.After Washing Buzzer beep or “End” on display. 1.If default is selected, step 3 can be skipped. 2.The function button line chart is for reference only, please refer to real product as standard. Note!
V.2Pull out the dispenser Caution!
- Detergent only need to be added in "case I “after selectingpre-washing for machines with this function. OPERATIONS Detergent Dispenser Pre wash detergent Main wash detergentSoftener Release button to pull out the dispenser
I •As for the agglomerated or ropy detergent or additive, beforethey are poured into the detergent box, it is suggested to usesome water for dilution to prevent the inlet of detergent boxfrom being blocked and overflowing while filling water.•Please choose suitable type of detergent for the variouswashing temperature to get the best washing performancewith less water and energy consumption. Note! Programme ○ Means optional Means must Programme
- Please choose the suitable type of detergent to get a maximum of washing performance and a minimum of water and energy consumption
- To achieve the best cleaning result a proper detergent dosing is important.
- Use a reduced detergent amount if the drum is not filled completely.
- Always adjust the amount of detergent to the water hardness, if your tap water is soft, use less detergent.
- Dose according to how dirty your laundry is, less dirty clothes require less detergent.
- Highly concentrated (compact detergent) requires particularly accurate dosing. Following symptoms are a sign of detergent overdosing: -heavy foam formation -poor washing and rinsing result Following symptoms are a sign of detergent underdosing: -laundry turns grey -built-up of limescale deposits on the drum, the heating element and/or the laundry Agglomerating or ropy detergent or additive can be diluted in some water before pouring it into the detergent dispenser, to avoid its inlet to get blocked and thus cause a water overflow. Note! Recommended washing detergent Heavy-duty detergent with bleaching agents and optical brighteners Colour detergent without bleaching agent and optical brighteners Color or mild detergent without optical brighteners Mild washing detergent Special wool detergent Wash cycles Washing temp. Type of laundry and textile White laundry made from boil-proof cotton or linen Coloured laundry made from cotton or linen Coloured laundry made from easy care fibres or synthetic materials Delicate textiles, silk, viscose Wool Algodón, ECO 40-60, Mix Algodón, ECO 40-60, Mix Sintéticos Sintéticos 20/30/ 40/60/90 20/30 20/30/40 Fría/20/30
V.2OPERATIONS On/Off Product is switched On/Off. Inicio/Pausa Press the button to start or pause the washing cycle. Programmes Available according to the laundry type. Función This allows you to select an additional function and will light when selected. Note! The chart is for reference only, Please refer to real product as standard.
Display The display shows the settings, estimated time remaining, options, and status messages for your washer. The display will remain on through the cycle.
- The above data is for reference only, and the data may change due to different actual use conditions.
- The valves given for programmes other than the ECO 40-60 programme are indicative only.
- Concerning to Regulation(EU) No 1061 /201 O, The EU energy efficiency class is: A+++; Energy test program: lntensive 60/40ºC; Speed: The highest speed; Other as the default. Half load for 8.0Kg machine: 4.0Kg.
- The above data is for reference only, and the data may change due to different actual use conditions.
- The valves given for programmes other than the ECO 40-60 programme are indicative only.
- Concerning to Regulation(EU) No 1061/201 0,The EU energy efficiency class is: A+++; Energy test program: lntensive 60/40 ºC; Speed: The highest speed; Other as the default. Half load for 9.0Kg machine: 4.5Kg.
40 70%/800 1:30 0.830
V.2OPERATION 1)The highest temperature reached by the laundry in the wash cycle for at least 5 minutes. 2)Residual moisture after the wash cycle in water content percent and the spin speed at which this was achieved. 3)The ECO 40-60 programme is able to clean normally soiled cotton laundry declared to be washable at 40°C or 60°C, together in the same cycle. This programme is used to assess the compliance with the regulation (EU) 2019/2023. The most efficient programmes in terms of energy consumption are generally those that perform at lower temperatures and longer duration. Loading the household washing machine up to the capacity indicated for the respective programmes will contribute to energy and water savings. Noise and remaining moisture content are influenced by the spinning speed: the higher the spinning speed in the spinning phase, the higher the noise and the lower the remaining moisture content. Caution! If there is any break in the power supply while the machine is operating, a special memory stores the selected programme. The machine will continue the programme when the power supply is re-established.
V.2Programmes OPERATIONS Programmes Hard-wearing textiles, heat-resistant textiles made of cotton or linen. Washing the baby's clothes, it can make the baby's wear cleaner and make the rinse performance better to protect the baby skin. Washing few and not very dirty clothes quickly. Mixed load of textiles made of cotton and synthetics. Wash synthetic articles, for example: shirts, coats, blending. While washing the knitting textiles, detergent quantity shall be reduced due to its loose string construction and easily forming bubbles. Programmes are available according to the laundry type. Hand or machine-washable wool or richwool textiles. Especially gentle wash programme to prevent shrinkage, longer programme pauses (textiles rest in wash liquor). Extra spin with selectable spin speed. To increase the washing effects, washing time is increased. Consistent 70ºC washing ensures sterilization effects. Loading weight lower than 5kg is suggested. Extra short programme suitable for lightly soiled washing and small amounts of laundry. Default 40ºC not selectable, suitable for laundry washing at about 40ºC-60ºC Specially set in this machine to clean the drum and tube. lt applies 90 ºC high temperature sterilization to make the clothes washing more green. When this programme is performed, the clothes or other washing cannot be added. When proper amount of chlorine bleaching agent is put in, the barrel cleaning effect will be better. The customer can use this programme regularly according to the need. This programme is suitable for wash the sportwear. Extra rinse with spin. Express 15' Lana Mix Algodón 20℃ Solo Centrifugado Aclarado y centrifugado Ropa bebé Esterilización Sintéticos Rápido 45' Autolimpieza Sport Edredones ECO 40-60 Intensivo 20ºC default, can choose cold water. Specially designed for washing duvet coats.
V.2OPERATION Option For the maximum spin speed, program time, and other details of the ECO 40-60 program, please refer to the content on the Product Fiche page. The table shows which cycle offers which options for adjustment. lf an adjustment is not possible for a cycle. Note
V.2OPERATION Temp. When needed, the washing temperature can be adjusted by pressing the temperature button in the following steps: Cold -20ºC-30ºC-40ºC-60ºC-90ºC. Spin Speed When needed, the spinning speed can be adjusted pressing the Speed button in the following steps: 1400 : 0-400-600-800-1000-1200-1400 Delay
Press the Delay button to choose the delaying time 0-24h
Press [Start/Pause] to start the delay operation Choose programme Setting time Start To cancel the Del ay function, press the "Del ay'' button befo re starting the program until the display shows O h. lf the program has already started, switch the appliance off and afterwards on and select a new programme. Pre Wash Extra washing function before the main washing cycle starts to increase the washing performance. Note: Detergent needs to be added to the compartment l. Extra Rinse The laundry will undergo an extra rinse after selecting this function. Soil Level The washing time will increase or decrease after you select it. Hygiene function When the Hygiene Function light is on, this function is automatically activated in the program. The Self-Clean function will be automatically activated during every washing cycle. Hygiene Pro syetem will keep your laundry always clean. Temp. Diferido Centrifug. Diferido
V.2OPERATION Child Lock This function is meant to keep children from misusing the controls.Press [Centrifug.] and [Inicio diferido] simultaneously for 3 sec until the buzzer beep. The child lock indicator switches on.Inicio diferidoCentrifug. Mute the buzzer To act the buzzer function, press the button again for 3 seconds. The setting will be kept until the next reset.
- After Muting the buzzer function, the sounds will not be activated any more. Caution! Press the [Temp.]button for 3sec., the buzzer is mute.Temp.Choose the Programme
- Only press and hold the two button can release child lock, even power off, switch off and program end
- The "Child Lock" will lock all buttons except Power button and Child Lock button
Please release child lock before selecting program and staring washing Caution!
- Don't use the Reload function when the water level over the edge of the inner tub or the temperature is higher. Reload This operation can be executed during the washing progress. When the drum is still rolling and there is large amount of water with high temperature in the drum. The state is unsafe and the door cannot be opened forcefully. To press [Start/Pause] for 3 sec. to reload, and start the clothes adding in the midway function. Please follow the steps as bellow: 1.Wait until the drum stops rotation. 2.The door lock is unlocked. 3.Close the door when the clothes are reloaded and press the button . Start Press [ ]3sec. Clothes Reload the clothes Caution!
V.2Before your maintenance starts, please unplug the machine and close the tap. Formic acid and its diluted solvents or equivalent are forbidden, such as alcohol, solvents or chemical products,etc. Don’t put laundry in the washing machine during the drum cleaning.
Warning! Note! Note! Cleaning And Care Cleaning The Drum The rusts left inside the drum by the metal articles shall be removed immediately with chlorine-free detergents. Never use steel wool. Cleaning The Cabinet Proper maintenance on the washing machine can extend its working life. The surface can be cleaned with diluted non-abrasive neutral detergents when necessary. If there is any water overflow, use the wet cloth to wipe it off immediately. No sharp items are allowed. Cleaning The Door Seal And Glass Wipe the glass and seal after each wash to remove lint and stains. If lint builds up it can cause leaks. Remove any coins, buttons and other objects from the seal after each wash. MAINTENANCE
V.2MAINTENANCE Washing the filter in the tap 1.Close the tap.2.Remove the water supply hose from the tap.3.clean the filter.4.Reconnect the water supply hose. Cleaning The Inlet Filter
- Inlet filter must be cleaned if there is less water.
- If the brush is not clean, you can pull out the filter washed separately;•Reconnect,
urn on the tap. Washing the filter in washing machine: 1.Screw off the inlet pipe from thebackside of the machine.2.Pull out the filter with long nose pliersand reinstall it back after beingwashed.3.Use the brush to clean the filter.4.Reconnect the inlet pipe. Note! Note! Clean The Detergent Dispenser Do not use alcohol,solvents or chemical products to clean the machine.Pull out the dispenser drawer with press the AClean the dispenser drawer under waterClean inside the recess with an old toothbrushInsert the dispenser drawer Note! 1.Press down the arrow location on softener cover inside thedispenser drawer.2.Lift the clip up and take out softener cover and wash all grooveswith water.3.Restore the softener cover and push the drawer into position.
- Make sure that the machine has finished the washing cycle and is empty. Switch it off and unplug it before cleaning the drain pump filter.
- Be careful of hot water. Allow the water to cool down. Risk of scalding!
- Clean the filter periodically every 3 months to ensure the normal operation of the appliance. Warning! When the appliance is in use and depending on the programme selected there can be hot water in the pump. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When replacing the cover, ensure it is securely re-tightened. Caution! Open the Service filterOpen the filter by turning to the counter clockwiseRemove extraneous matter Close the lower cover cap
V.2Trouble Shooting Whenever there is a problem with the appliance, check if you can solve it following the tables below. If the problem persists, please contact the customer service. MAINTENANCE Description Reason Solution Restart after the door is closedCheck if the clothes is stuck Door is not closed properlyDoor can’t be openedWasher's safety protection design is workingDisconnect the power, restart the productWater leakageThe connection between inlet pipe or outlet hose is not tightCheck and fasten water pipesClean up outlet hoseClean and wipe the detergent box Abnormal noise Check if the fixing (bolts) have been removedCheck it’s installed on a solid and level floorIndicator or display does not lightDisconnect the power PC board or harness has connection problemCheck if the power is shut down and the power plug is connected correctlyMachine cannot start upDetergent resi-dues in the boxDetergent is dampened or agglomeratedFixing bolts still in place.Floor is not solid or level. Error Codes Description Reason Solution Check if the water pressure is too lowStraighten the water pipeCheck if the inlet valve filter is blockedCheck if the drain hose is blockedWater injecting problem while washing Overtime water drainingTry again first, call up service line if there are still troublesOthersWater overflowRestart the washerRestart after the door is closed Check if the clothes is stuck Door is not closed properly After the check, activate the appliance. If the problem occurs or the display shows other alarm codes again, contact the service. Note!
V.2 Customer service In case of questions please contact our customer service at: Risk of electric shock
- Never try repair an appliance which is defective of presumed to be defective. You may put your own and future users' lives in danger. Only authorised specialists are allowed to carry out this repair work.
- Improper repair will void the warranty and subsequent damages can't be recogniced!
IMPORTANT STEPS WHEN MOVING THE APPLIANCE
- Unplug the appliance and close the water inlet tap.
- Check, if the door and the detergent dispenser are closed properly.
- Remove the water inlet pipe and the outlet hose from the house installations.
- Let the water drain completely from the appliance (see “Maintenance Cleaning the drain pump filter”)
- Important: Re-install the 4 transport bolts in the back of the appliance.
- This appliance is heavy. Transport with care. Never hold any protru- ding part of the machine when lifting. The machine door cannot be used as a handle.60
is used. 2)The actual water consumption will depend on how the appliance is used and on the hardness of the water. Product Data Sheet concerning (EU) 2019/2014 The product data sheet for your appliance can be found online. Go to https://eprel.ec.europe.eu and enter the model identifier for your appliance to download the data sheet. The model identifier for your appliance can be found in the technical specifications section.
This appliance is guaranteed for three years from the date of sale against all manufacturing defects, including labour and spare parts. In order to justify the date of purchase, it will be compulsory to present the invoice or purchase receipt. The conditions of this warranty apply only to Spain and Portugal. If you have purchased this product in another country, please consult your distributor for the applicable conditions. WARRANTY EXCLUSIONS
1. Remote controls, drain intake rubbers, dockings and door seals, weather stripping.
2. Damage to enamels, paints, nickel plating, chrome plating, oxidation or other types of
aesthetic parts or components that do not affect the internal functioning of the appliance.
3. Damage to wear parts due to use, corrosion or oxidation, whether caused by normal use
of the appliance or accelerated deterioration due to unfavorable environmental or climatic circumstances. Not suitable for outdoor use.
4. Damage to fragile pieces of glass, glass ceramic, plastics, handles, baskets, doors or light
bulbs when their failure or breakage is not attributable to a manufacturing defect.
5. Faults produced by fortuitous causes or accidents of force majeure, or as a consequence
of abnormal, negligent or inappropriate use of the device.
6. Civil liabilities of any nature.
7. Consequential damage to the appliance as long as it has not been caused by an internal
8. Maintenance or upkeep of the appliance: periodic reviews, adjustments and greases.
9. Faults that accessories and complements, adapters, external cables, bags, spare parts of
all kinds, lamps, as well as any part considered consumable by the manufacturer, may suffer. 10.Faults caused by incorrect or illegal installation, inadequate ventilation, lack of groun-ding in the home, power disturbances, inappropriate modifications or use of non-original spare parts.
11. Appliances used in industrial applications or for commercial purposes.
12. Appliances with illegible or altered serial number.
13. Defects or breakdowns produced as a result of fixes, repairs, modifications, or disassembly
of the installation of the device by the user or by a technician not authorized by the manufacturer, or as a result of manifest non-compliance with the manufacturer's instructions for use and maintenance.
14. During the warranty period it is essential to keep all manuals together with the
equipment. If the equipment is sold, donated or given away, the manual and all related documents must be given to the new user. If any of these are lost, their replacement cannot be claimed.
15. Faults that have their origin or are a direct or indirect consequence of: contact with
liquids, chemicals and other substances, as well as conditions derived from the climate or the environment: earthquakes, fires, floods, excessive heat or any other external force , such as insects, rodents and other animals that may have access to the interior of the machine or its connection points.
16. Damages derived from terrorism, riot or popular tumult, legal or illegal demonstrations
and strikes; facts of actions of the Armed Forces or the State Security Forces in times of peace; armed conflicts and acts of war (declared or not); nuclear reaction or radiation or radioactive contamination; vice or defect of the goods; facts classified by the Government of the Nation as "national catastrophe or calamity". Design and specifications are subject to change without notice for product improvement. Any changes to the manual will be updated on our website, you can check the latest version. www.easelectric.es
EasyManual