CODIX 520 - Measuring equipment Kübler - Free user manual and instructions

USER MANUAL CODIX 520 Kübler

nschlussbelegung: EinbaurahmenIf the digital display is used to monitor machines or processes in which, in case of a failure of the device or an error made by the operator, there might be risks of damaging the machine or causing accidents to the operators, it is your responsibility to take appropriate safety meas- ures.

INP Dynamic count input. RESET Dynamic RESET input. Linked in parallel to the red RESET key. Sets the counter to zero.

3. Setting of the operating parameters

a. Press both front side keys keys and switch on the supply voltage or, if the supply voltage is already on, press both keys simultaneously during 5 s. b. The display shows c. After releasing the keys, the display shows c1. Hold the left key pressed and press the right key to leave the programming operation c2. Press the right key to switch to d. Hold the left key pressed and press the right key to switch to the first parameter. e. After releasing the the right keys, the display alternates between the menu title and the cur- rent menu item setting. After pressing down any key, only the menu item setting is dis- played. f. Pressing the right key, the menu item setting will be switched to the next value. If figures are to be input (e.g. when setting the scaling factor), select first the digit using the left key, and then set the value using the right key. g. Hold the left key pressed and press the right key to switch to the next menu item. h. The last menu title ”EndPro” allows, when selecting “Yes”, to exit the programming menu

• Red LED display, character height 8 mm

• Programming via two setting keys on the front side

• During programming, the display guides the user with text prompts

1.1 Safety instructions and warnings

Only use this display – in a way according to its intended purpose – if its technical condition is perfect – adhering to the operating instruc- tions and the general safety instruc- tions.

1.2 General safety instructions

1. Before carrying out any installation or mainte-

nance work, make sure that the power supply of the digital display is switched off.

2. Only use this digital display in a way according

to its intended purpose: If its technical condition is perfect. Adhering to the operating instructions and the general safety instructions.

3. Adhere to country or user specific regulations.

4. The digital display is not intended for use in

areas with risks of explosion and in the branches excluded by the standard EN 61010

5. The digital display should only operated if it

has been correctly mounted in a panel, in accordance with the chapter “Main technical features”.

1.3 Use according to the intended purpose

The digital display may be used only as a panel- mounted device. Applications of this product may be found in industrial processes and controls, in manufacturing lines for the metal, wood, plastics, paper, glass, textile and other processing indus- tries. Over-voltages at the terminals of the digital dis- play must be kept within the limits in Category II

4.2 Switching on the 30 Hz filter (INP)

4.5 End of programming

The programming routine is

epeated once more. The val- ues set until now can be checked and modified. The programming routine wil be left and all values set will be stored as new parameters. Afterwards the device is ready for operation.

npn: switching to 0 V pnp: switching to +U

and to take over (store) the new values. If “no” is selected, the programming routine is repeat- ed, the latest values set remaining active. They

an now be checked aain or modified.

4. Programming routine

The programmable parameters of the device are described below, in succession. The device is fully programmed after one pass of the routine. The first values stated correspond to the factory settings

4.1 Polarity of the inputs

• where bounce occurs, e.g. with contacts

torage temperature: –25 ... +70 °C Altitude: to 2000 m EMC: Noise emission EN 55 011 Class B Noise immunity EN 61 000-6-2 Housing: For front panel mounting 48 x 24 mm acc. to DIN 43700, RAL 7021, dark grey Weight: appr. 50 g Protection: IP 65 (front) Cleaning: The front of the units is to be cleaned only with a soft wet (water!) cloth.

6. Terminal assignment

8. Delivery includes:

1 Digital display 1 Panel mounting clip 1 Bezel for screw mounting, panel cut out 50 x 25 mm 1 Bezel for clip mounting, panel cut out 50 x 25 mm 1 Seal 1 Multilingual operating instructions

• at maximum frequency square wave pulses 1:14