BD 5050 C Bp - Scrubber Kärcher - Free user manual and instructions

Product type	Walk-behind scrubber dryer
Brand	Kärcher
Model	BD 5050 C Bp
Rated voltage	24 V
Battery capacity	80 Ah (5h)
Total power consumption	1100 W
Brush rotation speed	180 rpm
Brush diameter	510 mm
Working width	500 mm
Fresh water tank	50 L
Waste water tank	50 L
Weight (empty)	87 kg
Weight in operation (max)	138 kg
Theoretical cleaning performance	2000 m²/h
Maximum incline	2 %
Max water temperature	50 °C
Sound level (LpA)	66 dB(A)
Protection rating	IPX3
Cleaning programs	Off, Normal, Intensive, Suction
Water flow adjustment	Yes, via rotary knob
Battery type	Lithium-ion (80 Ah)
Charger	External, charging time 8 h (standard) / 2 h (rapid)
Display	Yes, with error code display
Included accessories	Red disc brush (standard), suction bar 850 mm

Frequently Asked Questions - BD 5050 C Bp Kärcher

How to charge the battery of the Kärcher BD 5050 C Bp scrubber dryer?

To charge the battery, disconnect the battery connector on the device side and connect it to the suitable charger (ref. 6.654-479.0 or 6.654-480.0). Plug the charger into a mains socket. Charging time is approximately 8 h (standard) or 2 h (rapid). Do not use the device while charging. Important: Follow the safety instructions of the charger.

What does the error code ERR B displayed on the screen mean?

Error code ERR B indicates that a foreign object is blocking the brush. To resolve, set the program selector to OFF, release the safety switch, remove the foreign object, wait 3 seconds, then restart. If the error persists, contact customer service.

What is the capacity of the fresh water and waste water tanks?

The fresh water tank has a capacity of 50 liters and the waste water tank also has a capacity of 50 liters. This allows efficient cleaning over a long period without needing to empty or refill frequently.

How to adjust the water flow on the Kärcher BD 5050 C Bp?

Turn the water quantity adjustment knob located on the control panel. Start with a low flow and gradually increase until the desired result is achieved. Too high a flow may leave water residues.

How to replace the disc brushes?

Push the device down at the handlebar to lift the cleaning head. Press the brush change pedal downwards, then move the device backward to access the brush. Place the new brush on the floor, then move the device over it and lower the head to engage it.

How to clean the lint sieve?

Open the sieve cover, turn the lid clockwise and remove it. Take out the sieve, clean it with clean water, then put it back. Close the lid by turning counterclockwise. Perform this operation regularly to maintain performance.

What is the maximum incline on which the device can be used?

The maximum permitted incline for the work area is 2%. The device must not be used on steeper slopes. Caution: Do not use on inclined surfaces to avoid any risk of tipping.

Can I use detergents not recommended by Kärcher?

No. Only use detergents recommended by Kärcher (list in the manual). Using unsuitable detergents can damage the device and pose safety risks. Avoid solvents, hydrochloric or hydrofluoric acids, and high-foaming products.

How to transport the scrubber dryer safely?

For transport, raise the transport chassis pedal. Push the device by the handlebar. Only use it on slopes below the maximum value (2%). When transporting in a vehicle, secure the device against slipping and tipping according to applicable regulations.

How to maintain the suction lips?

The suction lips should be checked regularly. If they are worn down to the wear mark, they must be turned or replaced. To do this, remove the suction bar, unscrew the knurled knobs, remove the plastic parts, change the lips, then reassemble. Clean them with a damp cloth.

USER MANUAL BD 5050 C Bp Kärcher

Line drawing of a cleaning or cleaning machine with no visible text or symbols

Deutsch 3

English 11

Français 19

Italiano 28

Nederlands 36

Español 44

Português 53

Dansk 61

Norsk 69

Svenska 77

Suomi 85

Ελληνικά 93

Türkçe 103

Русский 111

Magyar 121

Čeština 129

Slovenščina 137

Polski 145

Românește 153

Slovenčina 161

Hrvatski 169

Srpski 177

Български 185

Eesti 195

Latviešu 203

Lietuviškai 211

Українська 219

Indonesia 229

中文 237

ไทย 244

العربية 259

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

Technical line drawing of a mechanical assembly with no visible text or symbols

Mechanical assembly diagram showing a vehicle suspension system with rotating components (no text or labels)

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Illustration of a hand holding a flexible hose with arrows indicating force or movement (no text or symbols)

Technical line drawing of a vehicle wheel assembly (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a curved arrow indicating rotation.

Technical diagram showing three-step assembly of a mechanical component with labeled parts and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Line drawing of a cleaning or cleaning machine with two wheels (no text or symbols)

Technical diagram of a vehicle interior with numbered components and wiring connections

Technical diagram showing labeled mechanical components with numbered parts 1, 2, 3, and 4

1 Schwimmergehäuse

2 Rasthaken

3 Schwimmer

4 Unterteil

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Please read and comply with these original instructions prior to the initial operation of your appliance and store them for later use or subsequent owners.

Contents

Safety instructions	EN 1
Function.	EN 1
Proper use.	EN 1
Environmental protection.	EN 1
Warranty	EN 1
Operating and Functional Elements.	EN 2
Before Startup	EN 3
Operation.	EN 3
Shutting Down the Appliance	EN 4
Transport	EN 4
Storage	EN 4
Care and maintenance	EN 4
Frost protection	EN 6
Faults.	EN 6
Accessories	EN 8
Technical specifications.	EN 8
EU Declaration of Conformity	EN 8
Declaration of Conformity	EN 8
Accessories and Spare Parts	EN 8

Safety instructions

Before using the appliance for the first time, read and observe these operating instructions and the accompanying brochure: Safety information for brush cleaning units and spray-extraction units, No. 5.956-251.0.

The device may only be operated when the cover and all lids are closed.

The appliance must only be operated on surfaces that do not exceed the max. permitted incline (see "Technical Specifications").

△WARNING

Do not use the appliance on inclines.

Safety Devices

Safety devices serve to protect the user and must not be rendered in operational or their functions bypassed.

Safety Switch

If the safety switch is released, the brush drive shuts off.

Danger or hazard levels

DANGER

For an immediate danger which can lead to severe injuries or death.

△WARNING

For a possibly dangerous situation which could lead to severe injuries or death.

△CAUTION

Pointer to a possibly dangerous situation, which can lead to minor injuries.

ATTENTION

Pointer to a possibly dangerous situation, which can lead to property damage.

Information on battery (accumulator) and charger

Lithium-ion batteries are installed in the appliance. These are subject to special criteria. The removal and the installation as well as the examination of defective batteries may only be performed by the Kärcher aftersales service or a specialist.

Information on storage and transport can be obtained from your Kärcher aftersales service.

△DANGER

- Alterations and modifications on the appliance are prohibited.

- Do not open the battery, as there is a risk of an electrical shock; also, irritating or caustic vapors can escape.

Do not expose the battery to direct sunlight, heat or fire, there is a risk of explosion.

- Do not operate the charger in explosive environment.

- Ensure sufficient ventilation during the charging process.

- Do not use the charger if dirty or wet.

- Do not work with open flames, generate sparks or smoke in the vicinity of a battery or a battery charging room. Danger of explosion.

△WARNING

- Check the appliance and the power cable for damage prior to every use. Do not use damaged appliances and have damaged parts repaired by specialists only. Keep children away from batteries and charger. Do not charge damaged batteries. Have damaged batteries replaced by the Kärcher aftersales service.

- Do not discard defective batteries in the domestic waste, inform Kärcher after-sales service.

- Avoid contact with liquids oozing out of defective battery packs. Rinse thoroughly if you accidentally come in contact with the fluid. Also consult a doctor if the fluid comes in contact with your eyes.

△CAUTION

- These operating instructions must be observed unconditionally. Observe recommendations of the lawmaker for handling batteries.

- The mains voltage must correspond with the voltage indicated on the type plate of the appliance.

- Use the charger only to charge approved battery packs.

- The accumulator may only be operated with this appliance. It is dangerous and prohibited to use it for other purposes.

Function

The scrubbing vacuum cleaner is used for the wet cleaning of level floors.

- The device can be easily adjusted to the respective cleaning task by adjusting the water volume and the detergent volume. The detergent dosing unit can be adjusted via the addition in the tank.

- The device is equipped with a fresh water and a waste water tank (50 litres each). These allow an effective cleaning with a long usage life.

- A working distance of 500 mm will improve the efficiency when you are using the appliance for a long period.

- Propulsion is accomplished by manually pushing the device and is supported by the rotation of the brushes.

Note:

The appliance can be equipped with various accessories depending on the cleaning task.

Please request our catalogue or visit us on the Internet at www.kaercher.com.

Proper use

Use this appliance only as directed in these operating instructions.

• This appliance is suited for the commercial use, e.g. in hotels, schools, hospitals, factories, shops, offices, and rental companies.
• The appliance may only be used for the cleaning of hard surfaces that are not sensitive to moisture and polishing operations.
• The appliance is not suited for the cleaning of frozen grounds (e.g. in cold stores).
• The appliance may only be equipped with original accessories and spare parts.
  – The appliance is not suited for the use in potentially explosive environments.
• The machine should not be used to suck in inflammable gases, undiluted acids or solvents.

This includes petrol, thinning agents or hot oil that can form an explosive mixture when it comes in contact with sucked air. Do not use acetone, undiluted acids and solvents as they are aggressive towards the materials from which the appliance is made.

- The machine has been approved for use on surfaces with max. gradients as listed under "Technical Specifications".

- The application temperature ranges from +5^ to +40^ .

Environmental protection

The packaging material can be recycled. Please do not throw the packaging material into household waste; please send it for recycling.

Old appliances contain valuable recyclable materials that should be recycled properly. Batteries, oil, and similar substances must not be released into the environment. Please dispose of your old appliances using appropriate collection systems.

Information on ingredients (REACH)

The latest information on ingredients can be found under:

The warranty terms published by our competent sales company are applicable in each country. We will repair potential failures of your accessory within the warranty period free of charge, provided that such failure is caused by faulty material or defects in fabrication. In the event of a warranty claim please contact your dealer or the nearest authorized Customer Service center. Please submit the proof of purchase.

Operating and Functional Elements

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

1 Fluff filter
2 Safety button
3 Battery *
4 Drain hose for wastewater with dosing unit
5 Holding rail for home base
6 Float
7 Fresh water tank
8 Fresh water tank lock
9 Cleaning head
10 Disc brush
11 Fresh water reservoir filler neck
12 Bow brush change
13 Waste water tank
14 Pedal transport chassis
15 Fresh water level display
16 Rotary handle to incline the vacuum bar
17 Height adjustment of suction bar
18 Wing nuts for fastening the vacuum bar
19 Vacuum bar *

20 Suction hose
21 Water quantity regulator
22 Battery socket
23 Vacuum bar lowering lever
24 Operator console
25 Push handle
26 Storage surface for cleaning set "Home base box"
27 Cover waste water tank

* not included in the delivery

Colour coding

• The operating elements for the cleaning process are yellow.
• The controls for the maintenance and service are light gray.

Operator console

6 1 2 3 4 5 KARCHER Professional

1 OFF

Device is switched off

2 Normal mode

Wet clean the floor and vacuum up dirt water.

3 Intense mode

Wet clean the floor and allow the detergent to react.

4 V a c u u m mode Suck in the dirt fleet.

5 Program selection switch

6 Display

Symbols on the machine

	Battery socket
	Lashing point
	Mop holder **
	Filling level fresh water tank 25%
	Bow brush change
	Vacuum bar lowering lever
	Drain outlet fresh water tank
	Dirt water discharge hose
	Transport chassis1: Transport0: Operation

** option

Before Startup

Unloading

→ Unscrew the screws from the middle board of the pallet.
→ Push down the device holding the push handle and pull out the middle board.

→ Remove the chocks in front of and next to the wheels.
→ Push down the device holding the push handle and push it forwards up to the edge of the pallet.
→ Lift the device off the pallet and set it on the floor.

Check battery

→ Check that the circular connectors and the screw connections of the battery poles are tight.
→ If necessary, retighten the cables on the battery poles with a torque wrench:
Screw M8: 18 Nm
Screw M10: 23 Nm

Charging battery

Note:

The device is equipped with a safety mechanism to prevent total discharge, i.e. when the permissible minimum capacity is reached, the brush motor and the turbine are switched off.

→ Drive the machine directly to the charging station; avoid any steep gradients in the process.

△DANGER

Danger of injury due to electric shock. Observe the mains voltage and fuse protection on the type plate of the device.

Charging process

The charging time depends on the battery condition and the charger.

When the battery is empty, the charging time is approximately:

Charger Charging time, approx. [h]
6.654-479.0 8
6.654-480.0 2

The appliance must not be used during the charging process.

ATTENTION

Risk of damage. Do not clean the device with water while the tank is removed.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

1 Battery plug, appliance side
2 Battery plug, battery side

→ Detach the battery plug on the unit side.

ATTENTION

Risk of damage!

• Do not connect the charger with the battery plug on the unit side.

- Only use a charger that is suitable for the installed battery type:

Battery type Charger
6.654-454.0 6.654-479.0
	6.654-480.0

Note: Please read the operating instructions of the charger manufacturer, especially the chapters on safety instructions!

→ Connect the battery plug on the battery side with the charger.
→ Plug the mains plug of the charger into a power outlet.
→ Execute the charging process according to the information in the operating instructions of the charger.
→ Disconnect the power cord of the charger.
→ Disconnect the battery connector from the charger.
→ Connect the battery plug on the device side with the battery plug on the battery side.

Installing the Vacuum Bar

→ Insert the vacuum bar into the vacuum bar suspension in such a manner that the profiled sheet is positioned above the suspension.
→ Tighten the wing nuts.

Technical line drawing of a mechanical assembly with no visible text or symbols

→ Insert the suction hose.

Operation

△DANGER

Risk of injury!

In dangerous situations, release the safety switch/drive lever.

Filling in detergents

Fresh water

→ Open the lock of the fresh water reservoir.
→ Fill up fresh water (maximum 50 °C) until the lower edge of filling nozzle.
→ Close the lock of the fresh water reservoir.

Detergent

△WARNING

Risk of damage. Only use the recommended detergents. With other detergents, the operator bears the increased risk regarding the operational safety and danger of accident. Only use detergents that are free from solvents, hydrochloric acid and hydrofluoric acid. Follow the safety instructions for using detergents.

Note:

Do not use highly foaming detergents.

Recommended detergents:

Application Detergent
Routine cleaning of all water resistant floors	RM 746RM 780
Routine cleaning of glossy surfaces (e.g. granite)	RM 755 es
Routine cleaning and basic cleaning of industrial floors	RM 69 ASF
Routine cleaning and basic cleaning of fine stoneware tiles	RM 753
Routine cleaning of tiles in sanitary areas	RM 751
Cleaning and disinfection in sanitary areas	RM 732
Removal of coating from all alkali-resistant floors (e.g. PVC)	RM 752
Removal of coating from li-noleum floors	RM 754

→ Add the detergent to the fresh water reservoir.

Note:

If the fresh water tank is empty, the cleaning head continues working without liquid supply.

Setting the water quantity

→ Adjust the water quantity using the regulating button according to the dirt on the floor covering.

Note:

Carry out initial cleaning attempts with low water volume. Increase water volume step-by-step until the desired cleaning result is achieved.

Setting the Vacuum Bar

Oblique position

To improve the vacuuming result on tiled floors the vacuum bar can be turned to an oblique position of up to 5°.

→ Loosen the wing nuts.
→ Turn the vacuum bar.

Mechanical assembly diagram showing a vehicle suspension system with rotating components and mounting brackets (no text or labels)

→ Tighten the wing screws.

Inclination

If the vacuum result is unsatisfactory the inclination of the straight vacuum bar can be modified.
→ Adjust the rotary handle to incline the suction bar.

Height

The bend of the suction lips upon contact with the floor is influenced with the height adjustment.

Technical line drawing of a mechanical assembly with springs and rotating components (no text or symbols)

→ Try adjusting the twist handles of the height adjustment until the best vacuuming result is achieved.

Cleaning

ATTENTION

Risk of damage to the floor covering. Do not operate the appliance on the spot.

→ Swivel the pedal for the transport chassis down.
→ Turn the program selection switch to the desired cleaning program.

Lower the vacuum bar

→ Pull the lever out and press it down; the vacuum bar is lowered.

Note:

• For cleaning tiled floors, adjust the straight suction bar in such a way that cleaning is not done at an angle of 90 degrees to the joints.
• The inclined position and the inclination of the suction bar can be adjusted to achieve better suction results (see "Adjusting the suction bar").
• If the waste water tank is full, the float closes the suction opening and the suction turbine runs at an increased speed. If this is the case, shut the vacuum off and drive to empty the waste water tank.

Shutting Down the Appliance

→ Release the safety switch.
→ Set the program selection switch to suction or vacuuming.
→ Briefly drive forward and suck of the remaining water.
→ Raise the vacuum bar.
→ Charge battery, if required.

Drain off dirt water

⚠ WARNING

Please observe the local provisions regarding the wastewater treatment.

→ Take the water discharge hose from the support and lower above a suited collection device.

Diagram showing a hand holding a flexible hose connected to a device with arrows indicating force or movement (no text or symbols present)

→ Crush or bend the dosing equipment.
→ Open the lid of the dosing equipment.
→ Drain off the dirt water - regulate the water quantity by pressing or bending.
→ Rinse the waste water tank with clear water.

Drain off clean water

Technical line drawing of a vehicle wheel and dashboard (no text or symbols)

→ Unscrew the lock of the fresh water reservoir.

Transport

△DANGER

Risk of injury! When loading or unloading the machine, it may only be operated on gradients up to the maximum value (see "Technical Specifications"). Drive slowly.

△CAUTION

Risk of personal injury or damage! Mind the weight of the appliance during transport.

→ Lift the pedal for the transport chassis.
→ Use the pushing handle to push the appliance.

Technical line drawing of a mechanical device with no visible text or symbols

→ When transporting in vehicles, secure the appliance according to the guidelines from slipping and tipping over.

Storage

△CAUTION

Risk of personal injury or damage! Consider the weight of the appliance when storing it.

This appliance must only be stored in interior rooms.

Care and maintenance

△DANGER

Risk of injury! Set the programme selector switch to "OFF" and pull the mains plug of the charger prior to performing any work on the appliance.

→ Drain and dispose of the dirt water and the residual fresh water.

Maintenance schedule

After each operation

ATTENTION

Risk of damage. Do not sluice the appliance with water and do not use aggressive detergents.

→ Drain off dirt water.

→ Rinse the waste water tank with clear water.
→ Clean the outside of the appliance with a damp cloth which has been soaked in mild detergent.
→ Check the fluff filter, clean if required.
→ Clean the vacuum lips and the wiping lips, check for wear and replace if required.
→ Check the brush for wear and replace if required (see "Maintenance tasks").
→ Charge the battery if required.

Monthly

→ Check battery poles for oxidation.
→ Check that the battery cables are tight,
→ Clean the seals between waste water tank and cover and check for tightness, replace if required.
→ Clean sieve.
→ For long periods of disuse, only turn the device off when the battery is fully charged. Fully recharge the battery at least every month.

Yearly

→ Have the prescribed inspection carried out by the customer service.

Maintenance Works

Cleaning the sieve

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a curved arrow indicating rotation.

1 Cover

2 Cover

→ Open the cover.
→ Turn cover the clockwise and remove it.
→ Remove and clean the sieve lying beneath it.
→ Insert the sieve.
→ Replace the cover and lock it by turning it anti-clockwise.
→ Close cover.

Replace or turn vacuum lips

1 2 CHANGE LIP

1 Wear indicator

2 Vacuum lip

The vacuum lips must be replaced or reversed if they are worn down to the wear indicator.

→ Remove the vacuum bar.
→ Unscrew the star grips.

Technical diagram showing mechanical assembly with numbered components and rotation indicators

→ Remove the plastic parts.
→ Remove the vacuum lips.
→ Insert new or reversed vacuum lips.
→ Insert the plastic parts.
→ Screw in and tighten the star grips.

Replacing the disk brushes

→ Push down the device holding the push handle so that the cleaning head is raised.
→ Press the pedal for changing the brushes downward beyond its resistance.

Technical line drawing of a cleaning or cleaning machine component with a downward arrow indicating a detail (no text or symbols present)

→ Pull the device towards the back so that the disc brush becomes accessible.
→ Place a new disc brush on the floor in front of the device.
→ Drive the device with the raised cleaning head over the new disc brush and lower the cleaning head.

The brush locks into the drive.

Removing the waste water tank

→ Drain off dirt water.

Line drawing of a cleaning or cleaning machine with two wheels (no text or symbols)

→ Lift up the waste water tank and put it aside.

Batteries

DANGER

Risk of explosion. Do not place tools or the like on the battery, i.e. on the terminal poles and cell connectors.

Recommended batteries

	Order No.
80 Ah 6.654-454.0

Insert batteries and connect

→ Drain off dirt water.

→ Lift up the waste water tank and put it aside.
→ Pull out the battery plug.

1 2 3 4

1 Spacer
2 Battery
3 Round plug
4 Battery pole

→ Place the battery into the device as shown above.
→ Insert the spacer between the battery and the device on the side indicated in the picture.

△CAUTION

When removing and installing the battery, the position of the machine might become unstable. Please ensure that it is in a secure position.

→ Clamp the connecting cables supplied onto the (+) and (-) battery terminals.
→ Plug both circular connectors into the battery.

ATTENTION

If the polarity is reversed (positive and negative terminals), the control electronics are destroyed.

Pay attention to correct poles.

→ Place the waste water tank on the appliance.

Note:

Charge the batteries before commissioning the appliance.

See also "Charging the batteries".

Removing the batteries

→ Set the programme selector switch to "OFF".
→ Pull out the battery plug.
→ Lift up the waste water tank and put it aside.
→ Unplug both circular connectors from the battery.
→ Clamp off the minus pole of the battery.
→ Disconnect the cable from positive terminal of the battery.
→ Remove the support blocks or the foam pieces.

△CAUTION

When the batteries are installed and removed, the stability of the appliance can be compromised; ensure a safe stance.

→ Remove the batteries.
→ Dispose of the used batteries according to the local provisions.

Maintenance contract

To ensure a reliable operation of the appliance maintenance contracts can be concluded with the competent Kärcher sales office.

Frost protection Faults

In case of danger of frost:

→ Empty the fresh and waste water tank.
→ Store the appliance in a frost-protected room.

△DANGER

Risk of injury! Set the programme selector switch to "OFF" and pull the mains plug of

the charger prior to performing any work on the appliance.

→ Drain and dispose of the dirt water and the residual fresh water.

Faults with display

Display Correction
ERR B Check if foreign objects block the brush; remove foreign object if required.Set the programme selector switch to "OFF", release the safety switch, wait for 3 seconds, restart.
ERR T	Set the programme selector switch to "OFF", release the safety switch, wait for 3 seconds, restart.If the event recurs, call Customer Service.
LOW BAT Charge battery.If the error is still displayed, check the two circular connectors on the battery are properly connected.If the event recurs, call Customer Service.
ERR TEMP Allow device to cool down.
HANDS OFF	Release the safety switch and wait until the operating hours or the battery status are displayed. Then operate the safety switch again.
ERR REL	Set the programme selector switch to "OFF", release the safety switch, wait for 3 seconds, restart.If the event recurs, call Customer Service.
ERR PWM	Set the programme selector switch to "OFF", release the safety switch, wait for 3 seconds, restart.If the event recurs, call Customer Service.

Battery status display

1 2 3 4

1 Battery
2 Button
3 "Status" LED
4 Indicator LED

→ Press the button for 5 seconds.

No LED lights up:

Charge the battery.

The status LED lights up green:

Together, all 5 LEDs indicate the battery's charging state.

The status LED lights up red:

The indicator LEDs indicate a malfunction. Malfunctions described in the following table can be remedied by the user. Contact KÄRCHER Customer Service for all malfunctions indicated not described above.

					Cause Correction
red	-	-	-	-	Battery too hot.	Allow the battery to cool down.
red	-	-	-	green	Battery management system too hot.	Allow the battery to cool down.
red	-	-	green	-	Battery too cold for charging.	Move the device to a warmer place and wait until the battery has warmed up.
red	-	-	green	green	Current consumption too high during charging.	Unplug the mains plug of the charger. Wait 10 seconds. Reinsert the mains plug. If the malfunction is displayed again, replace the charger.
					Device current consumption too high.	Switch off the device. If the malfunction occurs again after switching on, look for a fault in the device.
red	-	green	-	green	Short-circuit	Check all battery connections.
red	-	green	green	-	Cell voltage too low during discharge.	Charge battery.
red	-	green	green	green	Cell voltage too high during charging.	Discharge battery to 20% remaining capacity. Then charge the battery.
red	green	-	-	green	Battery voltage too low.	Charge battery.
red	green	-	green	-	Malfunction during charging process.	Unplug the mains plug of the charger. Wait 10 seconds. Reinsert the mains plug. If the malfunction is displayed again, replace the charger.
red	green	-	green	green
red	green	green	-	-	Battery too cold to output power.	Move the device to a warmer place and wait until the battery has warmed up.
red	green	green	green	-	Power output malfunction.	Switch off the device. If the malfunction persists, contact Customer Service.

Faults without display on the console

Failure Correction
Appliance cannot be started	Turn the program selection switch to the desired programme.
	Operate the safety switch.
	Insert battery plug.
	Check battery; charge it if required.
	Make sure that all battery terminals are connected.
Insufficient water quantity	Check fresh water level, refill tank if necessary.
	Increase the water volume on the regulating knob for water volume.
	Clean sieve.
Insufficient vacuum performance	Clean the seals between waste water tank and cover and check for tightness, replace if required.
	Wastewater reservoir is full; shut off the appliance and empty the wastewater reservoir
	Clean the fluff filter.
	Clean the vacuum lips on the vacuum bar, replace if required
	Check if the cover on the dirt water discharge hose is closed
	Check the setting of the vacuum bar.
	Check suction hose for blockages; clean if required.
	Check the suction hose for tightness; replace if required.
Insufficient cleaning result	Check the brushes for wear, replace if required.
	Increase the water volume.
	Check the brush type and the detergent for their suitability.
Suction turbine is running rough	Clean the swimmer.
Brush does not turn	Check if foreign objects block the brush; remove foreign object if required.
	If over-current switch in the electronics system has been triggered, turn programme selection switch to "OFF". Afterwards, set it back to the desired programme.
Vibrations during cleaning	You might need to use a softer brush.
In case of faults that cannot be remedied using the table below please contact the customer service.

Cleaning the floater

→ Open the cover of the waste water tank.

Technical diagram showing labeled components of a mechanical device, including parts 1, 2, 3, and 4.

1 Swimmer casing
2 Lock hook
3 Float
4 Lower part

→ Pull out the float casing towards the top.
→ Detach locking hooks.
→ Clean float and bottom part.
→ Assemble the float casing and insert it into the device.

Accessories

Description Part no.: Description
Disk brush, red (medium, standard)	4.905-026.0	For the use with all common cleaning tasks.
Disk brush, natural (white)	4.905-027.0	Made of natural fibres for spot cleaning and polishing.
Disk brush, black (hard)	4.905-029.0	For heavy soiling and for deep cleaning. For robust floorings only.
Driver plate pad 4.762-534.0 For cleaning with pads. With quick change coupling and center lock.
Pad, red (medium soft)	6.369-079.0	For cleaning and cleanering of all floors.
Pad, green (medium hard)	6.369-078.0	For cleaning heavily soiled floors and for deep cleaning.
Pad, black (hard)	6.369-077.0	With stubborn soiling and for deep cleaning.
Pad, beige (light grain)	6.369-468.0	For polishing and refreshing of hard and flexible floorings.
Pad, beige (natural hair proportion) 6.371-146.0
Suction bar, 850 mm, straight	4.777-401.0
Suction bar, 850 mm, bent	4.777-411.0
Set homebase box	4.035-406.0

Technical specifications

Power
Nominal voltage	V	24
Battery capacity	Ah(5h)	80
Average power consumption	W	1100
Rated power suction turbine	W	500
Rated power brush drive	W	600
Vacuuming
Vacuum power, air volume (max.)	l/s 24
Vacuuming power, negative pressure (max.)	kPa(mbar)	120
Type of protection		IPX 3
Cleaning brushes
Brush speed	1/min	180
Brush diameter	mm	510
Dimensions and weights
Theoretical surface cleaning performance	m2/h	2000
Max. working range in-cline	%	2
Fresh/waste water tank volume	l	50/50
Max. water temperature	°C	50
max. water pressure	bar	0.06
Net weight (transport weight)	kg	87
Total weight (ready to operate)	kg	138
Dimensions of battery compartment	mm	350 x 350
Values determined as per EN 60335-2-72
Total oscillation value	m/s2	<2.5
Uncertainty K	m/s2	0.2
Sound pressure level L_pA	dB(A)	66
Uncertainty K_pA	dB(A)	2
Sound power level L_WA + Uncertainty K_WA	dB(A)	81

EU Declaration of Conformity

We hereby declare that the machine described below complies with the relevant basic safety and health requirements of the EU Directives, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the machine is modified without our prior approval.

Product: Floor cleaner

Type: 1.127-xxx

1.515-xxx

Relevant EU Directives

2006/42/EC (+2009/127/EC)

2014/30/EU

2011/65/EU

Applied harmonized standards

EN 60335-1

EN 60335-2-72

EN 55012: 2007 + A1: 2009

EN 61000-6-2: 2005

EN 62233: 2008

EN IEC 63000: 2018

Applied national standards

The signatories act on behalf of and with of the authority of the company management.

Chairman of the Board of Management

Director Regulatory Affairs & Certification

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Declaration of Conformity

We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by

us. This declaration shall cease to be valid if the product is modified without our prior approval.

Product: Floor cleaner

Type: 1.127-xxx

1.515-xxx

Currently applicable UK Regulations

S.I. 2008/1597 (as amended)

S.I. 2016/1091 (as amended)

S.I. 2012/3032 (as amended)

Designated standards used

EN 60335-1

EN 60335-2-72

EN 55012: 2007 + A1: 2009

EN 61000-6-2: 2005

EN 62233: 2008

EN IEC 63000: 2018

National standards used

The signatories act on behalf of and with of the authority of the company management.

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Accessories and Spare Parts

Only use original accessories and spare parts, they ensure the safe and trouble-free operation of the device.

For information about accessories and spare parts, please visit www.kaercher.com.

Technical diagram of a cleaning or cleaning machine with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

Mechanical assembly diagram showing a bracket with mounting holes and rail tracks (no text or symbols)

Technical line drawing of a mechanical assembly with springs and bolts (no text or symbols)

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Diagram showing a cable being inserted into a device with arrows indicating direction (no text or symbols)

Technical line drawing of a vehicle wheel assembly (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a circular component and a screen.

1 Capot
2 Capot

Technical diagram showing mechanical assembly with numbered components and rotation indicators

Technical line drawing of a cleaning or repair machine component with a black arrow indicating a detail (no text or symbols present)

Technical line drawing of a cleaning or cleaning machine (no text or symbols present)

Technical diagram showing mechanical assembly with labeled parts 1, 2, 3, and 4

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

Technical line drawing of a mechanical assembly with no visible text or symbols

Mechanical assembly diagram showing a vehicle suspension system with rotating components (no text or labels)

Technical line drawing of a mechanical assembly with springs and rotating components (no text or symbols)

Diagram showing a hand connecting a flexible hose to a device with arrows indicating force or connection (no text or symbols present)

Technical line drawing of a vehicle wheel assembly (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including directional arrows indicating flow or movement.

1 Copertura

2 Coperchio

Technical diagram showing three-step assembly of a mechanical component with labeled parts and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

Technical diagram showing labeled components of a mechanical assembly, including parts 1, 2, 3, and 4.

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Accessori e ricambi

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

Technical line drawing of a mechanical assembly with no visible text or symbols

Technical line drawing of a mechanical assembly with springs and rotating components (no text or symbols)

Technical line drawing of a mechanical assembly with rotating components and springs (no text or symbols)

Diagram showing a hand holding a device with a coiled cable, indicating fluid or electrical connection (no text or symbols present)

Technical line drawing of a vehicle wheel assembly (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including directional arrows and a close-up of the component.

1 Afdekking
2 Deksel

Technical diagram showing three-step assembly of a mechanical component with labeled parts and directional arrows

Technical line drawing of a cleaning or cleaning machine component with a downward arrow indicating a detail (no text or symbols present)

Line drawing of a cleaning or cleaning machine with two wheels (no text or symbols)

→ Vuilwaterreservoir optillen en opzij zetten.

Accu's

⚠ GEVAAR

Technical diagram showing labeled components of a mechanical assembly, including parts 1, 2, 3, and 4.

4 Onderste deel

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

Technical line drawing of a mechanical assembly with no visible text or symbols

Technical line drawing of a mechanical assembly with springs and connectors (no text or symbols)

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Diagram showing a cable being inserted into a device with arrows indicating direction (no text or symbols)

Technical line drawing of a mechanical component with no visible text or symbols

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a directional arrow indicating rotation.

1 Cubierta 2 Tapa

Technical diagram showing three labeled mechanical components with rotational indicators and directional arrows indicating assembly or movement.

Technical line drawing of a cleaning or repair machine component with a downward arrow indicating a detail (no text or symbols present)

Technical line drawing of a cleaning or cleaning machine (no text or symbols present)

Technical diagram showing labeled components of a mechanical device, divided into two views with numbered parts.

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

1 Ficha da bateria, lado do aparelho 2 Ficha da bateria, lado da bateria

Technical line drawing of a mechanical assembly with no visible text or symbols

Mechanical assembly diagram showing a vehicle chassis with springs and rotating components (no text or symbols)

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Diagram showing a hand holding a flexible hose connected to a tray device, with arrows indicating direction of movement (no text or symbols)

Technical line drawing of a vehicle's front wheel and dashboard (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a directional arrow indicating rotation.

1 Cobertura
2 Tampa

Technical diagram showing three labeled mechanical components with rotational indicators and assembly steps

Technical line drawing of a cleaning or repair machine component with a downward arrow indicating a detail (no text or symbols present)

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

Desmontar as baterias

Technical diagram showing mechanical assembly with labeled parts 1, 2, 3, and 4

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning machine with numbered parts for identification.

Technical diagram of a robot with labeled parts and an inset view showing internal components

1 Batteristik, maskinside 2 Batteristik, batteriside

Technical line drawing of a mechanical assembly with rollers and a housing component (no text or symbols)

Mechanical assembly diagram showing a vehicle with springs and mounting brackets (no text or symbols)

→ Stram vingeskruerne.

Hældning

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Diagram showing a hand connecting a flexible hose to a device with arrows indicating force or connection (no text or symbols present)

Technical line drawing of a mechanical component with a circular head and cylindrical shaft (no text or symbols)

→ Skru friskvandtankens låg af.

Transport

⚠️FARE

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including directional arrows indicating movement.

1 Afdækning

2 Dæksel

Technical diagram showing mechanical assembly steps with numbered components and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

Technical diagram showing labeled mechanical components with numbered parts 1, 2, 3, and 4

1 Svømmerhus
2 Stopstifter
3 Svømmerventil
4 B u n d

H. Jenner Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Lader Ladetid, ca. [h]
6.654-479.0 8
6.654-480.0 2

Technical diagram of a robotic device with labeled parts and an inset showing internal components

Technical line drawing of a mechanical assembly with no visible text or symbols

→ Monter slangen.

Drift

△FARE

Technical line drawing of a mechanical assembly with springs and brackets (no text or symbols)

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Diagram showing a hand connecting a flexible hose to a device with arrows indicating force or connection (no text or symbols present)

Technical line drawing of a mechanical component with a circular head and handle (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including directional arrows indicating movement.

1 Deksel

2 Deksel

Technical diagram showing mechanical assembly steps with numbered components and rotation indicators

→ Ta av kunststoffdelene.
→ Trekk av sugeleppen.
→ Skyv inn de nye elle snudde sugelippene.
→ Sett på plass kunststoffdelene.
→ Sett på plass kryssgrepskruen og skru den godt til.

Skifte skivebørste

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Line drawing of a cleaning or cleaning machine with two different components (no text or symbols)

Technical diagram showing labeled components of a mechanical device, including parts 1, 2, 3, and 4.

1 Flottørkasse
2 Låseknaster
3 F l o t t ø r
4 Underdel

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

1 Batterikontrakt, maskinsida
2 Batterikontakt, batterisida

Technical line drawing of a mechanical assembly with no visible text or symbols

Mechanical assembly diagram showing a vehicle suspension system with rotating components and mounting brackets (no text or labels)

→ Dra fast vingskruvar.

Lutning

Technical line drawing of a mechanical assembly with rotating components and spring (no text or symbols)

Diagram showing a hand connecting a device to a coiled cable with arrows indicating force or connection (no text or symbols present)

Technical line drawing of a mechanical component with a circular head and adjustment knob (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a directional arrow indicating rotation.

1 Skydd

2 L o c k

Technical diagram showing mechanical assembly with numbered components and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Line drawing of two industrial cleaning machines (no text or symbols)

Technical diagram of a vehicle interior with numbered components and wiring connections

1 Distanshållare
2 B a t t e r i
3 Rundkontakt
4 Batteripol

Technical diagram showing labeled components of a mechanical device, including parts 1, 2, 3, and 4.

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning machine with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset showing internal components

Technical line drawing of a mechanical assembly with no visible text or symbols

→ Liitä imuletku.

Käyttö

VAARA

Loukkaantumisvaara!

Mechanical assembly diagram showing a vehicle suspension system with rotating components (no text or labels)

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Diagram showing a hand connecting a flexible hose to a device with arrows indicating force or connection (no text or symbols present)

Technical line drawing of a mechanical component with a circular head and handle (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including directional arrows indicating movement.

1 P e i t e

2 K a n s i

Technical diagram showing mechanical assembly with numbered components and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Line drawing of a cleaning or cleaning machine with two different components (no text or symbols)

Technical diagram showing labeled mechanical components in two views, with numbered parts 1 to 4 visible.

1 Uimurikotelo

2 Pidätinhaka

3 Uimuri

4 A I a o s a

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

Technical line drawing of a mechanical assembly with no visible text or symbols

Mechanical assembly diagram showing a vehicle suspension system with rotating components (no text or labels)

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Diagram showing a hand inserting a plug into a device with a coiled cable, indicating fluid or electrical connection (no text or symbols present)

Technical line drawing of a vehicle wheel assembly (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a directional arrow indicating rotation.

Technical diagram showing mechanical assembly with numbered components and rotation indicators

Technical line drawing of a cleaning or repair mechanism with no visible text or symbols

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

Technical diagram of a vehicle interior with numbered components and wiring connections

Technical diagram showing labeled mechanical components with numbered parts 1, 2, 3, and 4

1 Περίβλημα φλοτέρ

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robot with labeled parts and an inset view showing internal components

Technical line drawing of a mechanical assembly with rollers and guide rails (no text or symbols)

Mechanical assembly diagram showing a vehicle suspension system with rotating components (no text or labels)

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Diagram showing a hand connecting a flexible hose to a device with arrows indicating force or connection (no text or symbols present)

Technical line drawing of a vehicle wheel assembly (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a directional arrow indicating rotation.

1 Kapak
2 Kapak

Technical diagram showing mechanical assembly with numbered components and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a downward arrow indicating a detail (no text or symbols present)

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

	Sipariş No.
80 Ah 6.654-454,0

Technical diagram showing labeled mechanical components with numbered parts 1, 2, 3, and 4

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning machine with numbered parts for identification.

Technical diagram of a robot with labeled parts and an inset view showing internal components

Technical line drawing of a mechanical assembly with rollers and a housing (no text or symbols)

Mechanical assembly diagram showing a vehicle suspension system with hoses and springs (no text or labels)

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Diagram of a cable being inserted into a device with arrows indicating direction (no text or symbols)

Technical line drawing of a vehicle wheel assembly (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing vehicle component parts with numbered labels and directional arrows indicating motion or flow.

Technical diagram showing a mechanical assembly with numbered components and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

Technical diagram showing mechanical assembly with labeled parts 1, 2, 3, and 4

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning machine with numbered parts for identification.

Technical diagram of a robot with labeled parts, showing front and side views with numbered annotations.

Technical line drawing of a mechanical assembly with no visible text or symbols

Technical line drawing of a mechanical assembly with springs and brackets (no text or symbols)

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Diagram showing a hand connecting a device to a hose with directional arrows indicating movement (no text or symbols)

Technical line drawing of a mechanical component with a circular head and central hub (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a directional arrow indicating rotation.

1 Borítás
2 Fedél

Technical diagram showing mechanical assembly with numbered components and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

Technical diagram showing labeled components of a mechanical assembly, including parts 1, 2, 3, and 4.

1 Úszóház

2 Tartó kampó

3 Úszó

4 A l s ó r é s z

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

Technical line drawing of a mechanical assembly with rollers and a housing component (no text or symbols)

→ Nasad'te sací hadici.

Provoz

⚠NEBEZPEČÍ

Nebezpečí úrazu!

Technical line drawing of a mechanical assembly with springs and brackets (no text or symbols)

Technical line drawing of a mechanical assembly with springs and rotating components (no text or symbols)

Diagram showing a hand connecting a flexible hose to a device with arrows indicating force or movement (no text or symbols present)

Technical line drawing of a vehicle wheel assembly (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a curved arrow indicating rotation.

1 K r y t 2 K r y t

Technical diagram showing mechanical assembly with numbered components and rotation indicators

Technical line drawing of a cleaning or repair machine component with a downward arrow indicating a detail (no text or symbols present)

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

Technical diagram of a vehicle interior with numbered components and labeled parts

Technical diagram showing labeled components of a mechanical assembly, with numbered parts 1 to 4.

1 Kryt plováku

2 Z á k l a p k a

3 P l o v á k

4 Spodní díl

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

1 Vtič baterije, stran naprave
2 Vtič baterije, stran baterije

→ Izvlecite vtič baterije, ki je na strani naprave.

POZOR

Nevarnost poškodbe!

Technical line drawing of a mechanical assembly with no visible text or symbols

→ Nataknite gibko sesalno cev.

Obratovanje

⚠NEVARNOST

Nevarnost poškodbe!

Mechanical assembly diagram showing a vehicle suspension system with rotating components and mounting brackets (no text or labels)

→ Pritegnite krilate vijake.

Nagib

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Diagram showing a hand connecting a flexible hose to a device with arrows indicating force or connection (no text or symbols present)

→ Dozirno pripravo stisnite skupaj ali jo prepognite.
→ Odprite pokrov dozirne priprave.
→ Izpustite umazano vodo - s stisnjenjem ali prepognjenjem regulirajte količino vode.
→ Rezervoar za umazano vodo izperite s čisto vodo.

Technical line drawing of a vehicle wheel and dashboard (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a directional arrow indicating rotation.

1 Pokrov

2 Pokrov

→ Odprite pokrov.
→ Pokrov zavrtite v smeri urnega kazalca in ga snemite.
→ Odstranite in očistite sito, ki je pod pokrovom.
→ Vstavite sito.
→ Namestite pokrov in ga privijte v nasprotni smeri urinega kazalca.
→ Zaprite pokrov.

Technical diagram showing mechanical assembly with numbered components and rotation indicators

→ Snemite plastične dele.
→ Izvlecite sesalne brisalce.

→ Vstavite nove ali obrnjene sesalne nastavke.
→ Nataknite plastične dele.
→ Privijte zvezdaste ročaje in jih zategnite.

Zamenjava kolutne krtače

→ Napravo za potisno streme pritisnite navzdol, da se čistilna glava dvigne.
→ Pedal za zamenjavo krtač potisnite navzdol preko upora.

Technical line drawing of a cleaning or repair machine component with a downward arrow indicating a detail (no text or symbols present)

→ Napravo povlecite nazaj, tako da je kolutna krtača dostopna.
→ Novo kolutno enoto postavite pred na-pravo na tla.
→ Napravo z dvignjeno čistilno glavo za- peljite čez novo kolutno krtačo in spusti- te čistilno glavo.

Technical line drawing of a cleaning or cleaning machine (no text or symbols present)

→ Rezervoar za umazano vodo dvignite in postavite na stran.

Baterije

⚠NEVARNOST

Technical diagram showing labeled mechanical components with numbered parts 1, 2, 3, and 4

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Pribor in nadomestni deli

Uporabljajte samo originalen pribor in originalne nadomestne dele, ki zagotavljajo varno in nemoteno delovanje naprave. Informacije o priboru in nadomestnih delih najdete na www.kaercher.com.

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

Technical line drawing of a mechanical assembly with no visible text or symbols

Mechanical assembly diagram showing a vehicle suspension system with springs and rotating components (no text or labels)

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Illustration of a hand holding a flexible hose with arrows indicating direction (no text or symbols)

Technical line drawing of a mechanical component with a circular head and central hub (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing vehicle door panel and internal component with numbered parts and directional arrow

1 Ostona
2 Pokrywa

Technical diagram showing mechanical assembly with numbered components and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Line drawing of a cleaning or cleaning machine with two wheels (no text or symbols)

Zalecane akumulatory

Technical diagram of a vehicle interior with numbered components and labeled parts

1 Przekładka

Technical diagram showing labeled components of a mechanical device, including parts 1, 2, 3, and 4.

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robot with labeled parts and an inset view showing internal components

1 Conector baterie, partea aparatului
2 Conector baterie, partea de baterie

Technical line drawing of a mechanical assembly with no visible text or symbols

Mechanical assembly diagram showing a vehicle suspension system with rotating components (no text or labels)

→ Strângeti şuruburile-fluture.

Înclinatie

Technical line drawing of a mechanical assembly with springs and rotating components (no text or symbols)

Diagram showing a hand connecting a flexible hose to a device with arrows indicating force or connection (no text or symbols present)

Technical line drawing of a mechanical component with a circular head and central hub (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing vehicle door and door assembly with labeled parts 1 and 2

1 Capac

2 Capac

Technical diagram showing three-step assembly of a mechanical component with labeled parts and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

Technical diagram showing labeled components of a mechanical device, including parts 1, 2, 3, and 4.

Directive UE respectate:

2006/42/EG (+2009/127/EG)

2014/30/EU

2011/65/EU

Norme armonizate utilize:

EN 60335-1

EN 60335-2-72

EN 55012: 2007 + A1: 2009

EN 61000-6-2: 2005

EN 62233: 2008

EN IEC 63000: 2018

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning machine with numbered parts for identification.

1 Filtračné sito
2 Bezpečnostné spínače
3 Batéria *
4 Vypúšťacia hadica na znečistenú vodu s dávkovacím zariadením
5 Upevňovacia lišta pre Homebase
6 P I a v á k
7 Nádrž na čistú vodu
8 Uzáver nádrže na čistú vodu
9 Čistiaca hlava
10 Kefka na kotúče
11 Plniaci otvor nádrže na čistú vodu
12 Rukovät na výmenu kefy
13 Nádrž znečistenej vody
14 Pedál prepravného podvozka
15 Zobrazenie stavu naplnenia čistou vodou
16 Otočná rukovát' na sklonenie nasávacieho nosníka

17 Výškovo nastavitelný nasávací nadstavec
18 Krídlové matice na upevnenie sacej nadstavby
19 Sací nadstavec *
20 Vysávacia hadica
21 Regulačná hlava množstva vody
22 Zástrčka batérie
23 Páka spustenia sacej nadstavby
24 Ovládací panel
25 Posuvná rukovät
26 Odstavná plocha pre čistiacu súpravu „Homebase Box“
27 Kryt nádrže znečistenej vody

Technical diagram of a robotic device with labeled parts, including zoomed-in detail view

Technical line drawing of a mechanical assembly with rollers and guide rails (no text or symbols)

→ Nasad'te saciu hadicu.

Prevádzka

ΔNEBEZPEČENSTVO

Nebezpečenstvo zranenia!

Mechanical assembly diagram showing a vehicle suspension system with rotating components (no text or labels)

Technical line drawing of a mechanical assembly with rotating components and spring (no text or symbols)

Illustration of a hand connecting a flexible hose to a device with arrows indicating force or connection (no text or symbols)

Technical line drawing of a vehicle wheel assembly (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing vehicle door and door assembly with labeled parts 1 and 2

1 K r y t

2 V e k o

→ Otvorte kryt.
→ Kryt otočte v smere pohybu hodinových ručičiek a odoberte ho.
→ Vyberte sito pod ním a očistite ho.
→ Vložte sito.
→ Nasad'te kryt a zablokujte ho otočením proti smeru pohybu hodinových ručičiek
→ Uzavrite kryt.

Technical diagram showing three labeled mechanical components with rotational indicators and assembly steps

Technical line drawing of a cleaning or cleaning machine component with a downward arrow indicating a detail (no text or symbols present)

Line drawing of two industrial cleaning machines (no text or symbols)

Technical diagram showing labeled components of a mechanical device, including parts 1, 2, 3, and 4.

1 Teleso plaváka

2 Parkovací hák

3 P I a v á k

4 Spodná časť

→ Vytiahnite teleso plaváka hore.
→ Uvol'nite blokovací hák.
→ Vyčistite plavák a dolný diel.
→ Zmontujte teleso plaváka a zasuňte do prístroja.

Príslušenstvo

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset showing internal components

1 Akumulatorski utikač, strana uređaja
2 Akumulatorski utikač, akumulatorska strana

Technical line drawing of a mechanical assembly with no visible text or symbols

→ Nataknite usisno crijevo.

U radu

△OPASNOST

Opasnost od ozljeda!

U slučaju opasnosti pustite sigurnosnu sklopku/voznu polugu.

Punjenje radnih medija

Svježa voda

Mechanical assembly diagram showing a vehicle suspension system with rotating components and mounting brackets (no text or labels)

→ Zategnite krilne vijke.

Nagib

Technical line drawing of a mechanical assembly with springs and rotating components (no text or symbols)

→ Pomičite okretnu ručku namještanja visine tako da dobijete najbolji rezultat usisavanja.

Čišćenje

PAŽNJA

Diagram showing a hand connecting a device to a coiled cable with directional arrows indicating movement (no text or symbols)

→ Sabijte ili preklopite dozator.
→ Otvorite poklopac dozatora.
→ Ispustite prljavu vodu - pritiskanjem ili pre-savijanjem prilagođavajte količinu vode.
→ Spremnik prljave vode isperite čistom vodom.

Technical line drawing of a mechanical component with a circular head and cylindrical shaft (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a directional arrow indicating rotation.

1 Poklopac
2 Poklopac

Technical diagram showing three labeled mechanical components with rotational indicators and assembly steps

Technical line drawing of a cleaning or cleaning machine component with a downward arrow indicating a detail (no text or symbols present)

→ Izvucite uređaj unatrag da pločasta četka bude lako dostupna.
→ Položite novu pločastu četku na tlo ispred uređaja.
→ Uređaj s podignutim blokom čistača na- vezite na novu pločastu četku pa spusti- te blok čistača.
Četka se uglavljuje u pogon.

Skidanje spremnika prljave vode

→ Ispustite prljavu vodu.

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

→ Podignite spremnik prljave vode i stavite ga u stranu.

Akumulatori

△OPASNOST

	kataloški br.
80 Ah 6.654-454,0

Technical diagram of a vehicle interior with numbered components and wiring connections

Technical diagram showing labeled components of a mechanical device, including parts 1, 2, 3, and 4.

1 Kućište plovka

2 Uskočna kuka

3 P l o v a k

4 Donji dio

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning machine with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

1 Akumulatorski utikač, strana uređaja 2 Akumulatorski utikač, akumulatorska strana

6.654-454,0 6.654-479,0

6.654-480,0

Napomena: Pročitajte i sledite uputstvo za rad koje izdaje proizvođač motora, a prvenstveno sigurnosne napomene!

Technical line drawing of a mechanical assembly with rollers and a housing component (no text or symbols)

→ Nataknite usisno crevo.

Rad

△OPASNOST

Opasnost od povreda!

U slučaju opasnosti pustite sigurnosni prekidač odnosno voznu polugu.

Punjenje radnih medija

Sveža voda

→ Otvorite zatvarač rezervoara sveže vode.
→ Doliti svežu vodu (maksimalno 50 °C) do donje ivice nastavka za punjenje.
→ Zatvorite zatvarač rezervoara sveže vode.

Deterdžent

⚠UPOZORENJE

Opasnost od oštećenja. Koristite samo preporučene deterdžente. Za druge deterdžente korisnik na sebe preuzima povećan rizik od nesreća i remećenja sigurnosti pri radu.

Mechanical assembly diagram showing a vehicle suspension system with rotating components (no text or labels)

→ Zategnite leptir zavrtnje.

Nagib

Technical line drawing of a mechanical assembly with spring and chain components (no text or symbols)

→ Pomičite obrtnu ručku namještanja visine tako da dobijete najbolji rezultat usisavanja.

Čišćenje

PAŽNJA

Diagram showing a hand connecting a flexible hose to a device with arrows indicating force or connection (no text or symbols present)

→ Sabijte ili preklopite dozator.
→ Otvorite poklopac dozatora.

→ Ispustite prljavu vodu - pritiskanjem ili presavijanjem prilagođavajte količinu vode.
→ Rezervoar prljave vode isperite čistom vodom.

Ispuštanje sveže vode

Technical line drawing of a mechanical component with a circular head and handle (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Prilikom transporta vozilima osigurajte uređaj od klizanja i nakretanja u skladu sa odgovarajućim važećim propisima.

Skladištenje

△OPREZ

Opasnost od povreda i oštećenja! Pri skladištenju imajte u vidu težinu uređaja. Ovaj uređaj se sme skladištiti samo u zatvorenim prostorijama.

Nega i održavanje

△OPASNOST

Opasnost od povreda! Pre svih zahvata na uređaju prekidač za izbor programa postavite na "OFF" i izvucite strujni utikač punjača.

→ Ispustite i uklonite prljavu i preostalu svežu vodu.

Plan održavanja

Posle svake primene

PAŽNJA

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a directional arrow indicating rotation.

1 Oplata
2 Poklopac

Technical diagram showing three labeled mechanical components with rotational indicators and directional arrows indicating motion or assembly.

→ Skinite plastične delove.
→ Skinite gumice za usisavanje.
→ Umetnite nove ili prevrnute gumice za usisavanje.
→ Nataknite plastične delove.
→ Zavijte i zategnite zvezdaste pričvrsnike.

Zamena pločaste četke

→ Uređaj pritisnite na dole držeći ga za potisnu ručku kako bi se blok čistača podigao.
→ Pedalu za zamenu četke pritisnite na dole prelazeći pritom preko osetnog otpora.

Technical line drawing of a cleaning or cleaning machine component with a downward arrow indicating a detail (no text or symbols present)

→ Izvucite uređaj unazad da pločasta četka bude lako dostupna.
→ Položite novu pločastu četku na tlo ispred uređaja.
→ Uređaj sa podignutim blokom čistača navezite na novu pločastu četku pa spustite blok čistača. Četka se uglavljuje u pogon.

Skidanje rezervoara za prljavu vodu

→ Ispustite prljavu vodu.

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

→ Podignite rezervoar za prljavu vodu i sklonite ga na stranu.

Akumulatori

△OPASNOST

	kataloški br.
80 Ah 6.654-454,0

Technical diagram showing labeled mechanical components with numbered parts 1, 2, 3, and 4

1 Kućište plovka

2 Uskočna kuka

3 P l o v a k

4 Donji deo

→ Kućište plovka izvucite naviše.
→ Otpustite uskočnu kuku.
→ Očistite plovak i donji deo.

Pribor

Naziv Br. dela Opis
Crvena (srednje mekana, standardna) pločasta četka	4.905-026.0	Za primenu za sve uobičajene zadatke čišćenja.
Prirodna (meka) pločasta četka	4.905-027.0	Od prirodnih vlakana za pranje i poliranje.
Crna (tvrda) pločasta četka	4.905-029.0	Za jaka zaprljanja i za temeljno čišćenje. Samo za neosetljive obloge.
Noseći kotur sa sunderastim diskom	4.762-534.0	Za čišćenje sunderastim diskom. Sa spojnicom za brzu zamenu i centralnim zaključavanjem.
Crveni, srednje mekani sunderasti disk 6.369-079.0 Za čišćenje i pranje svih podova.
Zeleni, srednje tvrdi sunderasti disk	6.369-078.0	Za čišćenje jako zaprljanih podova i za temeljno čišćenje.
Crni, tvrdi sunderasti disk	6.369-077.0	Za tvrdokornu prljavštinu i za temeljno čišćenje.
Sunderasti disk bež boje sa blagom granulacijom	6.369-468.0	Za poliranje i osvežavanje tvrdih i elastičnih obloga.
Sunderasti disk bež boje, delom od prirodne dlake 6.371-146.0
Ravna usisna konzola, 850 mm 4.777-401.0
Zakrivljena usisna konzola, 850 mm	4.777-411.0
Komplet Homebase Box	4.035-406.0

Tehnički podaci

Snaga
Nominalni napon	V	24
Kapacitet akumulatora	Ah(5h)	80
Prosečna potrošnja energije	W 1100
Nominalna snaga usisne turbine	W	500
Nominalna snaga pogona četki	W	600
Usisivanje
Maksimalna usisna snaga, protok vazduha	l/s	24
Maksimalan učinak usisavanja, podpritisak	kPa(mbar)	120
Stepen zaštite		IPX 3
Četke za čišćenje
Broj obrtaja četki 1/min	180
Prečnik četki	mm	510
Dimenzije i težine
Teoretski površinski učinak	m2/h	2000
Maks. nagib radne oblasti	%	2
Zapremina rezervoara sveže/prljave vode	l	50/50
Maks. temperatura vode	°C	50
maks. pritisak vode	bara	0,06
Neto težina (transportna težina)	kg	87
Ukupna težina uređaja spremnog za rad	kg	138
Dimenzije odeljka akumulatora	mm	350 x 350
Izračunate vrednosti prema EN 60335-2-72
Ukupna vrednost oscilacija	m/s2	<2,5
Nepouzdanost K	m/s2	0,2
Nivo zvučnog pritiska L_pA	dB(A)	66
Nepouzdanost K_pA	dB(A)	2
Nivo zvučne snage L_wA + nepouzdanost K_wA	dB(A)	81

Izjava o usklađenosti sa propisima EU

Ovim izjavljujemo da ovde opisana mašina po svojoj koncepciji i načinu izrade, sa svim njenim modelima koje smo izneli na tržište, odgovara osnovnim zahtevima dole navedenih propisa Evropske Zajednice o sigurnosti i zdravstvenoj zaštiti. Ova izjava prestaje da važi ako se bez naše saglasnosti na mašini izvedu bilo kakve promene.

Proizvod: mašina za pranje podova

Tip: 1.127-xxx

1.515-xxx

Chairman of the Board of Management

Director Regulatory Affairs & Certification

Opunomoćeni za izradu dokumentacije: S. Reiser

Alfred Kärcher SE & Co. KG

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Pribor i rezervni delovi

Technical diagram of a cleaning or cleaning machine with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

Technical line drawing of a mechanical assembly with no visible text or symbols

Technical line drawing of a mechanical assembly with springs and brackets (no text or symbols)

→ Затегнете крилчатите винтове.

Наклон

Technical line drawing of a mechanical assembly with springs and rotating components (no text or symbols)

Diagram showing a cable being inserted into a device with arrows indicating direction (no text or symbols)

Technical line drawing of a vehicle wheel assembly (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a circular component and a door.

1 K a n a k 2 K a n a k

Technical diagram showing mechanical assembly with numbered components and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Line drawing of a cleaning or cleaning machine with two wheels (no text or symbols)

Technical diagram showing labeled components of a mechanical device, including parts 1, 2, 3, and 4.

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

1 Akupistik, seadme pool

2 Akupistik, aku pool

→ Tömmake seadmepoolne akupistik ära. TÄHELEPANU

Kahjustusoht!

Technical line drawing of a mechanical assembly with no visible text or symbols

→ Pange imivoolik kohale.

Käitamine

△OHT

Vigastusoht!

Mechanical assembly diagram showing a vehicle with springs and mounting brackets (no text or symbols)

→ Pingutage tiibmutreid.

Kalle

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Diagram of a hand holding a flexible hose with arrows indicating force or movement (no text or symbols)

Technical line drawing of a mechanical component with a circular head and handle (no text or symbols)

→ Kruvige maha puhta vee paagi lukk.

Transport

A OHT

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including directional arrows and a close-up of the internal component.

1 Kate

2 K a a s

Technical diagram showing three labeled mechanical components with rotational indicators and directional arrows indicating motion or assembly.

Technical line drawing of a cleaning or cleaning machine component with a downward arrow indicating a detail (no text or symbols present)

Line drawing of two industrial cleaning machines (no text or symbols)

Akude mahamonteerimine

Technical diagram showing labeled components of a mechanical device, including parts 1, 2, 3, and 4.

1 Ujuki korpus
2 Kremoon
3 Ujuk
4 Alumine osa

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning machine with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

1 Akumulatora kontakts, aparāta puse
2 Akumulatora kontakts, akumulatora puse

Technical line drawing of a mechanical assembly with no visible text or symbols

Technical line drawing of a mechanical assembly with springs and brackets (no text or symbols)

→ Pievelciet spärnskrüves.

Slīpums

Technical line drawing of a mechanical assembly with springs and rotating components (no text or symbols)

Diagram of a handheld device with a coiled cable and directional arrows indicating motion (no text or symbols)

Technical line drawing of a mechanical component with a cylindrical head and circular base (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including directional arrows and a close-up of the component.

1 Pārsegs

2 V ā k s

Technical diagram showing mechanical assembly with numbered components and rotation indicators

Technical line drawing of a cleaning or repair machine component with a black arrow indicating a detail (no text or symbols present)

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

Technical diagram of a vehicle interior with numbered components and wiring connections

1 Star plika

2 Akumulators

3 Apalais spraudnis
4 Akumulatora pols

Technical diagram showing labeled mechanical components in two views, with numbered parts 1 to 4 visible.

1 Pludina korpuss

2 Fiksācijas ākis

3 Pludinš

4 A p a k š d a ! a

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

1 Filtro tinklelis
2 Apsauginis jungiklis
3 Baterija *
4 Nešvaraus vandens išleidimo žarna su dozatoriumi
5 Homebase laikomasis bégelis
6 Plūduras
7 Švaraus vandens bakas
8 Švaraus vandens bako dangtelis
9 Valymo galva
10 Diskinis šepetys
11 Švaraus vandens bako pildymo anga
12 Šepečio keitimas svirtis
13 Užteršto vandens bakas
14 Pedalais valdomas transportavimo mechanizmas
15 Švaraus vandens lygio indikatorius
16 Sukamoji rankena, skirta siurbimo ré-meliui pakreipti
17 Siurbimo rémelio aukščio reguliavimas

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

Technical line drawing of a mechanical assembly with no visible text or symbols

Mechanical assembly diagram showing a vehicle suspension system with rotating components (no text or labels)

→ Atsukite sparnuotasias veržles.

Pakreipimas

Technical line drawing of a mechanical assembly with springs and rotating components (no text or symbols)

Diagram showing a hand connecting a flexible hose to a device with arrows indicating force or connection (no text or symbols present)

Technical line drawing of a vehicle wheel assembly (no text or symbols)

→ Nusukite švaraus vandens talpyklos dangtelj.

Transportavimas

⚠PAVOJUS

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including directional arrows indicating movement.

1 Dangtis

2 Dangtis

Technical diagram showing three-step assembly of a mechanical component with labeled parts and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Line drawing of a cleaning or cleaning machine with two different components (no text or symbols)

Technical diagram of a vehicle interior with numbered components and wiring annotations

1 Tar p i k l i s

2 Baterija

3 Apvalusis kištukas

4 Akumuliatoriaus polius

Technical diagram showing labeled components of a mechanical device, including parts 1, 2, 3, and 4.

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

Technical line drawing of a mechanical assembly with no visible text or symbols

Technical line drawing of a mechanical assembly with springs and brackets (no text or symbols)

Technical line drawing of a mechanical assembly with springs and levers (no text or symbols)

Diagram showing a cable being inserted into a device with arrows indicating direction (no text or symbols)

Technical line drawing of a vehicle wheel assembly (no text or symbols)

Technical diagram showing labeled mechanical components with numbered parts, likely from an engineering or manufacturing context.

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

Technical line drawing of a mechanical assembly with no visible text or symbols

→ Pasang selang penyedot.

Pengoperasian

⚠BAHAYA

Bahaya kecelakaan!

Lepaskan tombol pengaman/engkol layan saat bahaya.

Mengisi cairan pengoperasian

Air bersih

Mechanical assembly diagram showing a vehicle with springs, levers, and a rotating shaft (no text or symbols)

→ Kencangkan sekrup sayap.

Kecondongan

Technical line drawing of a mechanical assembly with springs and rotating components (no text or symbols)

Diagram showing a hand holding a flexible hose with arrows indicating force or movement (no text or symbols)

Technical line drawing of a vehicle wheel assembly (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including a directional arrow indicating rotation.

1 Penutup
2 Penutup

Technical diagram showing mechanical assembly with numbered components and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a downward arrow indicating a detail (no text or symbols present)

Line drawing of a cleaning or cleaning machine with two different components (no text or symbols)

	No. order
80 Ah 6.654-454.0

Technical diagram showing labeled mechanical components in two views, with numbered parts 1 to 4 visible.

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

Penyusun dokumen yang berwenang:

S. Reiser

Alfred Kärcher SE & Co. KG

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2019/03/01

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset showing internal components

1 电池插头，设备侧

2 电池插头，电池侧

→ 拔出设备侧电池插头。

注意

有损坏危险！

Technical line drawing of a mechanical assembly with no visible text or symbols

→ 插上抽吸软管。

设备运作

△ 危险

存在受伤危险！

Mechanical assembly diagram showing a vehicle suspension system with hoses and brackets (no text or labels)

→ 拧紧翼型螺栓。

倾斜度

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Illustration of a hand connecting a flexible hose to a device with arrows indicating force or connection (no text or symbols)

Technical line drawing of a vehicle wheel assembly (no text or symbols)

→ 拧下净水箱的盖子。

运输

△ 危险

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal component with labeled parts 1 and 2, including a curved arrow indicating rotation.

1 盖
2 顶盖

Technical diagram showing mechanical assembly with numbered components and rotation indicators

→ 拔下塑料件。

→ 拔下吸嘴。

→ 插入新的或经翻转的吸嘴。

→ 插上塑料件。

→ 拧上并拧紧星形柄。

更换盘刷

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

→ 抬起污水箱并置于一侧。

电池

危险

Technical diagram showing labeled components of a mechanical assembly, with numbered parts 1 to 4.

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

Technical line drawing of a mechanical assembly with rollers and guide rails (no text or symbols)

→ โสมสายยางดูด

การใช้งาน

อันตราย

Mechanical assembly diagram showing a vehicle with springs, pulleys, and a shaft (no text or symbols)

→ ขันสกรหางปลา

ความเอียง

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Illustration of a hand connecting a medical device to a coiled tube, with arrows indicating force or movement (no text or symbols present)

Technical line drawing of a vehicle wheel assembly with no visible text or symbols

Technical line drawing of a mechanical device with no visible text or symbols

Technical diagram showing a vehicle's internal components with labeled parts 1 and 2, including directional arrows indicating movement.

1 ฟ้าครอบ

2 ฝาปิด

Technical diagram showing mechanical assembly with numbered components and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

Technical diagram showing labeled mechanical components in two views, with numbered parts 1 to 4 visible.

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

เอกสารมอบอํานาจ:

S. Reiser

Alfred Kärcher SE & Co. KG

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2019/03/01

Technical diagram showing mechanical assembly with labeled parts 1, 2, 3, and 4

Technical diagram of a vehicle interior with numbered components and wiring annotations

1 مباعدات

2 بطارية

3 قابس دانري

4 قطب البطارية

Technical diagram showing three-step assembly of a mechanical component with labeled parts and rotation indicators

Technical line drawing of a cleaning or cleaning machine component with a black arrow indicating a detail (no text or symbols present)

Technical line drawing of a cleaning or cleaning machine (no text or symbols)

Technical line drawing of a mechanical assembly with rotating components (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Mechanical assembly diagram showing a vehicle chassis with springs and levers (no text or symbols)

Technical diagram of a robotic device with labeled parts and an inset view showing internal components.

KURCHER Professional

Technical diagram of a cleaning or cleaning device with numbered parts for identification.

التمييز اللوني

Black silhouette of a hand giving a thumbs-up gesture (no text or symbols)

THANK YOU!

MERCI! DANKE! iGRACIAS!

Register your product and benefit from many advantages.

www.kaercher.com/welcome

Rate your product and tell us your opinion.

Icon showing a gear and wrench inside a square frame (no text or symbols)

www.kaercher.com/dealersearch

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28-40

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

QR code image with a central logo, likely linking to a digital resource or website.