Captur Timer Kit (Fujifilm) - Remote control Hähnel - Free user manual and instructions

Product Type	Remote with timer for Fujifilm SLR camera
Brand	Hähnel
Model	Captur Timer Kit (Fujifilm)
Usage	Remote triggering, burst shooting, long exposure, interval
Connection	Wireless via Captur Receiver module (included) or wired via supplied cable
Wireless Range	Up to 100 m (estimated)
Trigger Modes	Single, Burst, Long exposure (Bulb), Programmed interval
Interval Programming	DELAY, LONG, INTVL1, INTVL1 N, INTVL2, INTVL2 N
Setting Ranges	DELAY: 0s to 99h 59min 59s; LONG: adjustable; INTVL: 1s to 99h 59min 59s; N: 1 to 999 or unlimited
Memory	Retains settings after power off
Indicators	Trigger LED (green/red), battery indicator
Power Supply	1 CR2032 battery (included)
Battery Life	Several months depending on usage (estimated)
Dimensions (approx.)	80 x 50 x 25 mm
Weight (approx.)	80 g (with battery)
Materials	ABS plastic
Care and Cleaning	Clean with a soft, dry cloth. Avoid moisture and solvents.
Safety	Do not expose to heat, moisture, flames. Keep out of reach of children. Remove battery if not used for an extended period.
Spare Parts	Not provided by the manufacturer. Contact Hähnel support.
Repairability	Not user-serviceable. Contact an authorized service center.

Frequently Asked Questions - Captur Timer Kit (Fujifilm) Hähnel

How to set the delay before the first triggering (DELAY)?

Use the control button 15 (< or >) to navigate to the DELAY parameter (3). Press SET 14, then adjust the value with + or -. Press SET again to confirm. The delay can be set from 0 seconds to 99 hours 59 minutes 59 seconds.

How to use the remote in long exposure mode (Bulb)?

Select BULB mode on your camera. Press and hold the remote's trigger button to open the shutter (the LED blinks red after 3 seconds). Release to close. For longer exposures, program the LONG and INTVL parameters.

How to pair the timer module with the receiver (DCM)?

On the timer, hold down the trigger button while pressing ON. The LED turns green. On the receiver, hold down the + button while pressing ON. The LED turns red. DCM is activated. Turn off and on both modules to complete.

What is the battery life?

The remote uses a CR2032 battery. Battery life varies depending on usage (several months under normal use). The battery indicator (8) warns you when it is low.

Can I use this remote with a Canon or Nikon SLR?

This model is specific to Fujifilm cameras. Check compatibility with your body. The kit comes with a cable suitable for Fujifilm. Dedicated versions exist for other brands.

How to set the number of interval shots (INTVL1 N)?

Navigate to the INTVL1 N parameter (6). Press SET, adjust from 1 to 999 with + or -. For unlimited number, use the '...' symbol (unlimited). Confirm with SET.

The LED does not light up, what to do?

Check that the battery is correctly inserted (respect polarities). If the problem persists, replace the battery with a new one (CR2032). Make sure the ON button is firmly pressed.

How to use the remote in burst mode?

Select burst mode on your camera. Press Start/Stop to start the burst. The Captur Timer module will take pictures at predefined intervals. Press Start/Stop again to stop.

Can I trigger a flash remotely with this kit?

Yes, provided you have a Captur receiver for the flash and a compatible transmitter. Synchronize the DCM channels. Ensure the transmitter is compatible with the camera's hot shoe.

How to clean the remote?

Use a soft, dry cloth. Do not use solvents or abrasive products. Avoid any contact with water. Store in a dry place away from heat.

USER MANUAL Captur Timer Kit (Fujifilm) Hähnel

All product specifications subject to change without notice EAOI.

All brands, trademarks and registered trademarks are the property of their respective holders. Copyright © Nahel industries Ltd, Ireland

www.hahnel.ie

A product of tunnel industries Ltd., Ireland. Made in China

Rev 03/19

CAPTUR

Timer Kit

Habitat CAPTUR Module - Timer Habitat CAPTUR Timer

Manual

Connecting your Captur - Timer Kit

Wireless: Connect Receiver to Camera

Note: For Panasonic. Receiver end plug a grey in colour. Push in fully. Wireless UP TO 100m 24GHz Receiver Timer CAPTUR

Wired: Connect Timer to the camera

Note: For Panasonic. Timer ends plug is grey in colour. Push in fully. Timer CAPTUR

Captur Module - Timer 1

Captur - Timer Kit Controls

DELAY' LONG INTVL1 INTVL2 N 00:00' 00" [---] 9 10 11 Cable Port DELAYLONGINTVL1INTVL2N 88:88'88" [888] Release Button Lock Lock Start/Stop SET Off/On Start/Stop 13 14 15 hahnel APTUR Module - Timer

LED light Test/DCM button hahnel CAPTUR Receiver Off/On Cable Port Hotshoe (flash mount) Camera / Tripod Mount

Cables

Timer Kit - Canon C1 & C3 Cables (Canon only)

Timer Kit - Nikon N1 & N3 Cables (Nikon only)

Timer Kit - Sony S2 Cable (Sony only)

Timer Kit - Oly/Pana O1, P1 & C1 Cables (Olympus/Pana only)

Timer Kit - Fujifilm C1 & F1 Cables (Fujifilm only)

C1 Cable C3 Cable N1 Cable N2 Cable N3 Cable 51 Cable S2 Cable O1 Cable P1 Cable F2 Cable F1 Cable

Batteries

4 x AA All Balancing

Please insert all batteries provided. Instructions in this manual assume that the Captur Receiver & Timer and any other equipment are already turned on.

graph TD
    A["N1=3 shots"] --> B["SHOOT"]
    C["N1=3 shots"] --> D["SHOOT"]
    E["N1=3 shots"] --> F["SHOOT"]
    G["N1=3 shots"] --> H["SHOOT"]
    I["INTVL1"] --> J["10sec | 10sec"]
    K["INTVL2"] --> L["10sec | 10sec"]
    M["INTVL1"] --> N["10sec | 10sec"]
    O["INTVL2"] --> P["10sec | 10sec"]
    Q["INTVL1"] --> R["10sec | 10sec"]
    S["INTVL2"] --> T["10sec | 10sec"]
    U["N2=3 x INTVL1"] --> V["1Hr"]
    U --> W["20Sec"]
    U --> X["1min"]
    U --> Y["20Sec"]
    U --> Z["1min"]
    U --> AA["20Sec"]

Example:

3 DELAY = 01:00'00" Delay 1 hour
4 LONG = 00:00'00" No long
5 INTVL1 = 00:00' 10" 10 sec interval 1
6 N1 = [003] 3 shots interval 1
7 INTVL2 = 00:01'00" 1 min interval 2
6 N2 = [003] Repeat 3 x interval 1

Manual Remote Control

13 Green Red 1/2 Push Auto focus INDHEAI CAPTUR Module - Timer

Full Push SET Inchosi CAPTUR Mobile - Timer Shutter Release

graph TD
    A["SET"] --> B["DELAY 00:00' 00" [---"]]
    B --> C["LONG 00:00' 00" [---"]]
    C --> D["INTVL1"]
    D --> E["SET"]
    E --> F["INTVL1 00:00' 01" [---"]]
    F --> G["INTVL1 N [---"]]
    G --> H["SET"]
    H --> I["OUT"]
    I --> J["INTVL2"]
    J --> K["SET"]
    K --> L["INTVL2 00:00' 00" [---"]]
    L --> M["INTVL2 N [---"]]
    M --> N["SET"]
    N --> O["OUT"]
    O --> P["INTVL2"]

English 7

German 10

French 13

Polish 16

Dutch 19

Spanish 22

Czech 25

Portugese 28

Swedish 31

Finnish 34

Italian 37

Hebrew 40

1 2 3 4 5 6 Sound ON/OFF Button Lock DELAY Delay before shooting starts LONG Duration of burst/exposure with continuous/bulb INTVL1 1st Interval time INTVL1 N Number of shots at 1st Interval INTVL2 N Number of times INTVL1

program is repeated

INTVL2 2nd Interval time Low battery indicator Hours 00 00' Minutes 00" Seconds [---] Shot count 0 to 999, --- (unlimited) Shutter release LED SET button Toggle Button

Setting up Captur - Timer Kit

The Captur Module - Timer is used with the Captur Receiver to control the camera wirelessly. Alternatively you can also connect the Captur Module - Timer directly to a DSLR camera with the camera cable included.

Single Shot Mode

Select single shot □ on camera. The Release Button works similarly to the camera shutter release. 12 push = Autofocus, LED 13 shows steady green. Full push = Shutter release, LED 13 shows red.

Continuous Shot Mode

Select continuous mode ☐ on camera. Press and hold the Release Button - after 3secs timer LED flashes red = 🔍. Full press Release Button = 🔍

BULB Mode

Select BULB mode on camera. Press and hold the Release Button to open the shutter - after 3secs timer LED flashes red = Full press Release Button = to close shutter. For more advanced timed BULB shooting use the LONG and INTVL settings.

Interval Timer Programmable Functions

Press Start/Stop button to 'Start' the 'Interval Timed Photography'. The Captur Module - Timer will now take a photo continuously at the factory set interval time. Press Start/Stop again to 'Stop' the interval timed photography. The values of the following parameters can be adjusted as required. Use Toggle Button 15 < or > to move between the parameters which need to be adjusted. Press SET button 14 to adjusted parameters. Toggle Button 15 + or - is used to adjust the value of the parameters. Press SET button 14 again to confirm adjustment.

Parameters	Description	Setting
3 DELAY	Delay before 1st shutter is released	0s to max 99hrs 59'min 59"s (in 1s increments)
4 LONG	Burst/Bulb time
5 INTVL1	1st Interval Time	1s to max 99hrs 59'min 59"s (in 1s increments)
6 N	INTVL1 N = Number of shots for 1st Interval	1 to 999 and --- (unlimited)
	INTVL2 N = Number of times INTVL1 program is repeated
7 INTVL2	2nd Interval Time	1s to max 99hrs 59'min 59"s (in 1s increments)

Digital Channel Matching - DCM

a. Timer - Press and hold Release Button + Turn 'ON'. LED will flash green
b. Receiver - Press and hold button + Turn 'ON'. LED will show steady red
c. DCM is complete. Turn both Timer & Receiver 'OFF' and 'ON' to reboot
Note: For multiple Receivers repeat step 'b' for all receivers without turning off timer

Camera & Flash Remote Control

Requires an additional Captur receiver and Transmitter which are synced on a differnet channel.

Please note: To ensure camera and flash gun are in sync, flash receivers must be triggered from a transmitter fitted to the camera hotshoe.

graph TD
    A["Transmitter"] -->|Sync 1| B["Receiver"]
    C["Receiver"] -->|Sync 2| D["Timer"]
    style A fill:#f9f,stroke:#333
    style B fill:#ccf,stroke:#333
    style C fill:#cfc,stroke:#333
    style D fill:#fcc,stroke:#333

Warning

• Do not modify product
• Keep Captur - Timer Kit dry at all times
• Do not use in the presence of flammable gas
• Keep out of the reach of children
• Do not expose to excessive temperatures or strong direct sunlight
• Do not leave the unit in the trunk or on the dashboard of a vehicle
  • Overheating can result in leaking, fire or explosion
• Observe correct battery polarity
• Dispose in accordance with appropriate environmental regulations
  • Take battery out of unit if stored for an extended period of time

Press Start/Stop button to 'Start' the 'Interval Timed Photography'. The Captur Module - Timer will now take a photo continuously at the factory set interval time. Press Start/Stop again to 'Stop' the interval timed photography. The values of the following parameters can be adjusted as required. Use Toggle Button 15 < or > to move between the parameters which need to be adjusted. Press SET button 14 to adjusted parameters. Toggle Button 15 + or - is used to adjust the value of the parameters. Press SET button 14 again to confirm adjustment.

.הכלההוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָה

14 (SET)