PRO 9 XPERT - Lawn mower GAMA - Free user manual and instructions

Product Type	Professional Hair Clipper
Brand	GAMA
Model	PRO 9 XPERT
Dimensions (approx.)	18 x 5 x 5 cm
Weight (approx.)	300 g
Power Supply	Mains (power cable)
Supply Voltage	220-240 V
Double Insulation	Yes (symbol on the device)
Motor Power	Adjustable via set screw
Cutting Height Without Comb	0.8 mm to 3.8 mm (adjustable lever)
Cutting Heights With Combs	3 mm, 6 mm, 10 mm, 13 mm
Included Accessories	4 guide combs, cleaning brush, lubrication oil
Usage	Hair cutting, beard, neck fluff, sideburns
Maintenance	Dry cleaning (brush), regular lubrication
Lubrication Frequency	Domestic: monthly; Professional: daily
Cleaning	Do not clean under running water
Safety	Do not use near water, unplug after use
Warranty	1 or 2 years depending on consumer type (Directive 1999/44/EC)
Spare parts	Blades, cutting heads (replacement by manufacturer)
Repairability	Authorized technical center
Use	Domestic and professional
Product information	www.gamaprofessional.com

Frequently Asked Questions - PRO 9 XPERT GAMA

How to adjust the cutting height without comb?

Use the adjustable lever located on the left side of the clipper. Push it up for a 0.8 mm cut, down for 3.8 mm.

How to attach a guide comb?

Place the notch near the comb teeth on the blade, then push the comb base against the head until it clicks. To remove, pull the tab outward.

What are the cutting lengths with combs?

The provided combs allow cuts at 3, 6, 10, and 13 mm.

How to lubricate the blade?

Before first use, apply a few drops of oil on the blade (clipper tilted). Turn on for a few seconds to distribute the oil, then wipe off excess with a dry cloth.

How to clean the clipper?

Turn off and unplug the device. Remove the comb, then use the supplied brush to remove hairs between the blades. Never wash under running water.

Can I use the clipper in the bathroom?

No. The device must not be used near water or in a damp room to avoid electric shock.

How to adjust motor power?

Turn the black screw on the side of the device clockwise until you hear a loud noise, then slightly counterclockwise to reduce noise. The blade must be aligned horizontally.

What to do if the blade no longer cuts effectively?

Check cleaning and lubrication. If the problem persists, contact the manufacturer to replace the cutting head.

Can the clipper be used for beard?

Yes, without a guide comb, it allows trimming beard, neck fluff, and sideburns with an adjustable cut from 0.8 to 3.8 mm.

Where to find spare parts or the manual?

Visit www.gamaprofessional.com to download the manual or contact customer service.

USER MANUAL PRO 9 XPERT GAMA

READ AND KEEP FOR FUTURE NEEDS

[e-mail] / www.gamaprofessional.com

INDICE / INDEX

ITA/ITALIANO: 03
EN/ENGLISH: 11
FR / FRANÇAIS: 18
ESP/ESPAÑOL: 26
PT / PORTUGUES: 33
RU/PYCCK: 40
EAA / EAMHNIKA: 48
PL/POLSKI: 56
SWE/SVENSKA: 63
DE/DEUTSCH: 70
/8s : 77

ITA

Thank you for having purchased this GAMA BY GAMA SALON EXCLUSIVE product. We are sure that you will appreciate all the care that has gone into its design and manufacture. GAMA research constantly combines innovation and technology to create premium-quality products. Excellent performance is guaranteed since we apply the most advanced methods and use the best materials. This guarantees excellent performance, designed for the most demanding clients who wish to achieve excellent results. Read these instructions carefully before use and keep them for future reference.

IMPORTANT: READ CAREFULLY BEFORE USING THE APPLIANCE. SAVE THESE INSTRUCTIONS.

1- Do not use the appliance with wet hands, in a damp environment or on wet surfaces. Do not immerse the appliance in water or other liquids. 2- Do not use this appliance near bathtubs or other vessels containing water. 3- Unplug the appliance when it is off because proximity to water could pose a threat; be extra careful when using it in the bathroom. 4- Do not use this electric appliance if it has been in contact with liquids, if its electric cord is damaged or if its body and/or accessories show clear signs of damage. If the appliance does not work properly, disconnect it from the power immediately and take it to an approved service centre. 5- If the electric cord is

damaged, it must be replaced immediately by the manufacturer, an authorised service centre or similarly qualified persons in order to avoid a hazard. 6 - Keep the appliance and its electric cord away from sources of heat and from heat-sensitive surfaces (plastic, vinyl, etc.). 7- Do not hold or handle the appliance by the electric cord. Do not wind the electric cord around the appliance, bend it or twist it so as not to impair its correct functioning and thus damage the appliance. Lack of compliance with the above warnings and instructions could cause a short circuit and thus irreparable damage to the appliance, as well as put the user's safety at risk. 8- Unplug the appliance when not in use and allow it to cool down before storing it in a safe place. To disconnect the appliance, unplug the electric cord from the wall power outlet. 9- To clean the appliance, always disconnect it from the power outlet first and let it cool completely. When cleaning, do not use aggressive products containing phenylphenol. 10- This appliance should only be used for its intended purpose. 11- This appliance has especially sharp professional blades, so use it carefully to avoid injuries or lesions. 12- Always turn this appliance off before changing one of its accessories. 13- For additional protection the

installation of a residual current device (RCD) having a rated residual operating current not exceeding 30mA is advisable in the electrical circuit supplying the bathroom. Ask your installer for advice.

This appliance must not be used by people with reduced physical, motor or mental capacity (including children), or with limited knowledge of the appliance itself, unless such people have been trained for its use or are under adequate supervision to ensure their own safety. Children must be under supervision at all times to ensure that they do not play with the appliance.

Do not use this appliance near bathtubs or other vessels containing water.

This appliance has been designed with a double-insulation system for your safety.

The symbol on the product or on the package indicates that the product should not be considered as normal domestic waste; once you have decided to dispose of it, it should be taken to the proper collection point for recycling electrical and electronic appliances. When you

dispose of this product correctly, you help prevent potential negative consequences for the environment and health, which could derive from improper treatment of the product. For more detailed information on recycling this product, contact the municipal office, the local waste disposal service or the shop where it was purchased.

LIMITED WARRANTY:

Duration of warranty period: 1 or 2 years depending on customer category in compliance with Directive 1999/44/EC. For support service under warranty, please take the original purchase ticket / sales receipt to the shop where the product was purchased. The product will be repaired free of charge or immediately replaced with similar product of equal or greater value.

PRO9 XPERT

RECOMMENDATIONS FOR USE:

Before using the hair clipper the hair must be clean and dry. We recommend cutting small quantities of hair at a time, adjusting the cutting length gradually until finding the one you want. The blades risk getting stuck if too fast movements are made or if a lot of hair is cut at the same time. It can be used without attachment comb to trim beard, neck hair and sideburns.

BEFORE USING THE APPLIANCE:

Lubricate the blade before the first use. Read the instructions contained in the section "HOW AND WHEN TO LUBRICATE THE BLADE"

Adjust motor power. After oiling the appliance, its operation could be inefficient; therefore it is necessary to turn it on and follow the instructions given below to achieve optimal operation:

1. There is a black screw (Fig. 1) on the right side of the body of the appliance that can be used to change the power of your hair clipper's motor. This screw has been previously calibrated in our production line; however, depending on the voltage where the appliance is used, you may need to adjust it again. For this operation, you will need a screwdriver to be inserted in the screw cavity.

2. Turn the screw clockwise until hearing the loud noise emitted by the motor when it reaches the maximum speed; immediately after this, turn it anticlockwise until the motor noise decreases. Stop turning the screw only when the blade is horizontally aligned with the head and not beyond.

3. At this point the motor power has been adjusted and the hair clipper is ready for use.

USE INSTRUCTIONS:

• Insert the desired attachment. This operation should always be done with the hair clipper turned off.
• Turn on the hair clipper by pressing the (O/I) button.
• Turn off the hair clipper by pressing the (O/I) button.

INSERTION OF COMBS:

The supplied combs have two snap on seats. One near the teeth of each comb (Fig. 2) and the other near the base of each comb (Fig. 3). To insert the combs in the hair clipper, set the snap on base near the teeth of the comb on the hair clipper blade and then push the base of the comb against the base of the blade head until you hear a slight click: insertion will be now be completed. Remove the combs using the tab located on the base of the comb, exerting an outward force.

Fig.2

Fig.3

CUTTING LENGTH ADJUSTMENT:

The PRO9 XPERT hair clipper offers the possibility of making finishing touches from 0.8mm to 3.8mm (if used without any guide comb attached and using the adjustment lever) and performing classic hair cuts with the following lengths: 3, 6, 10 and 13mm .

ADJUSTABLE LEVER:

The lever for adjusting the cutting length is located on the left side of the body of the appliance (Fig. 4); this lever lets you adjust the cutting length to 0.8mm if held upwards, i.e. towards the upper body of the appliance, or 3.8mm if held downwards, i.e. towards the rear body of the appliance.

CLEANING AND MAINTENANCE:

A clean and properly lubricated hair clipper considerably improves its capacity and cutting precision. DO NOT CLEAN ANY PART OF THE APPLIANCE UNDER RUNNING WATER.

CLEANING THE HEAD:

Before any cleaning operation, make sure that the appliance is properly turned off and disconnected from the power outlet. Remove the accessory if it is inserted. Using the special brush supplied, remove any hair residues between the blades and the back of the blade head.

NEVER DISASSEMBLE THE HEAD INTO ITS INTEGRAL PARTS OR YOU WILL INVALIDATE THE WARRANTY ON THE ENTIRE PRODUCT.

HOW AND WHEN TO LUBRICATE THE BLADE:

Before the first use we recommend lubricating the blade with a drop of the oil found in the package or with any other lubricating oil (make sure that it is not too viscous).

Turn the hair clipper upside down (Fig. 5) so that oil does not drip on the appliance. Lubricate the blade with a few drops of oil. Turn the appliance on for a few seconds so that the oil is distributed evenly along the entire blade. Then, using a dry cloth, eliminate any excess oil residues. For professional users, the lubrication process must be carried out daily. In case of domestic use, it can be carried out monthly or more frequently, depending on the type of use of the product.

BLADE DURATION:

The duration of the blade varies based on usage frequency and times. Although correct maintenance is performed, if the cutting efficiency is compromised, contact the manufacturer to have the entire head replaced.

On the website www.gamaprofessional.com you can find all product and instruction manuals with related warnings and information.

The date of production of this model mentioned on the box label in the format: XXX - number of goods part; XX - day; XX - month; XX - year

FR

J 1
J-3.0
J 4.
J 5.
J 6.
J 7.
J 8.
J 9.

Jgiai jieill gic gaii aijie cuii i

10 11 12 13 14 15 16 17 18 19 20

aal aal (Jabla) y L) aal al g rnnn nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn n nn

y

CcSioxljg jjgljg jglj

a aal 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

gill golal gai gll sll wall e j yj w g d 1999/44/CE

aai i 1i 1i 1i 1i 1i 1i 1i 1i 1i 1i 1i 1i 1i 1i

PRO9 XPERT

:1i

Jb b 1000000000000000000000000000000000000000000000000000000000

1.5,2.5

a 1

:J1

1 1

A

a 3

1.

| x - 2| = | x - 4| = 1

slae jaiy aiai, laia iaaa oii j y.

.(0/1)

.(0/1)

jIg jIy

(2) (3)

2.

3

:

13963 108

：

J 4 100000000000000000000000000000000000000000000000000

jie 11

4

:aiuailguiibii

aaii aiee iieae eae ae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae eae

.

：

a 1

aaiiie 1

aaiuall aibii

J 1

y

J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1

AaLsIglllglJaaalil gaiy jiajaiy

：

15 2y 1) j 1 y j 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1