SHC 4354S - Beard trimmer SINBO - Free user manual and instructions

USER MANUAL SHC 4354S SINBO

OPERATING INSTRUCTIONS Before using, please read the instructions carefully.

SHC 4354S is our newest product which is supplied for family use, and for professional hairdressers to clip different hairstyles too. Comb attachments from 3mm to 15mm in total 9 positions: 3/4.5/6/7.5/9/10.5/12/13.5/15mm and 18/19.5/21/22.5/24/25.5/27/28.5/30mm. Before using at the first time, please charge 8 hours fully to activate the inside rechargeable batteries. PARTS IDENTIFICATION

1. Thinning out adjuster (push right and left), 2. Switch (push up and down), 3. Adjustment wheel

4. Indicator light, 5. Blade, 6. Comb attachment, 7. Adaptor, 8. Oil bottle, 9. Cleaning brush

How to use This hair clipper can be used in both cord and cordless.

1. Put the adaptor connect with the jack of battery pack which lies at the bottom of the machine, then

put the adaptor pins connect with AC power pay attention to the voltage, please coincide with the voltage on the nameplate of adaptor, the full charging time is 8 hours. When fully charged, it can be used continuously for more than 45 minutes. During charging, the indicator light shows red.

2. Push the switch button from 1 to 0, then it can be used.

3. For thinning out , please push the thinning out adjuster from right to left.

How to use the comb attachment When load and unload the comb attachment, please ensure the power switch to “0” position.

1. Please put the comb (long and sharp ends) into slots of clipper at the sides.

2. Using the adjustment wheel to adjust the length of comb (push up for long, back up for short)

3. While push the adjustment wheel, there are 9 positions to control the cutting length

(3/4.5/6/7.5/9/40.5/12/13.5/15mm or 18/19.5/21/22.5/24/25.5/27/28.5/30mm) Maintenance of the blades

1. Handing the hair clipper in obverse, then push the blade out of the machine, and then use the cleaning

brush to wipe off the scraps among the blade. Lubricating the space between the stationary and moving blades with 2 or 3 drops of oil .

2. Clean the blade after using every time in time. When resetting the blades, please press the full parts

until hearing the “KA” sound. When charging Please don’t charge if the temperature is lower than 0°C or higher than 40°C. Please don’t charge if it is nearby the sunlight perpendicular incidence or the heat source radiates. The standard charging time is 8 hours. In order to avoid mangling the batteries, please don’t extend the charging time. Cautions Cleaning the housing using only a cloth slightly dampened water or a mild soap solution. Never use a caustic solution. Never submerge the clipper in water. Keep away from the children. This clipper may become warm during operating and/or charging, this is normal. When using, don’t hold the power soft line, in order to prevent possible harm and so as to avoid accidents Never tamper with moving parts.- 8 - Technical Data: Charging Time: 8 Hours Operation Time: 45 Minutes (When fully loaded) Adaptor Input: AC 100-240V,50/60Hz Adaptor Output: 3 VDC, 600mA Please note: Be sure to charge one time at least within one year after the shipment. This appliance is not intended for use by persons (including children)with reduced physical,sensory of mental capabilities,or lack of experience and knowledge,unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety; Childred should be supervised to ensure that they do not play with the appliance. To prevent possible harm to the environment or human health from uncontrolled waste disposal,such as the unused batteries and motors etc,recycle them responsibly to promote the sustainable reuse of material resources.To return your used device,please use the return and collection systems or contact the retailer where the product was purchased.They can take this product for environmental safe recycing. Not to be used in bath or shower