SSI 2874 - Iron SINBO - Free user manual and instructions

Product type	Steam iron
Brand	Sinbo
Model	SSI 2874
Power supply	230 V, 50 Hz, 2200 W
Soleplate	Ceramic
Water tank capacity	380 ml
Continuous steam output	110 g/min
Steam shot	96 g
Steam shot volume	0.65 g/coup
Main functions	Dry ironing, steam, steam shot, spray, vertical steam
Anti-drip system	Yes
Self-cleaning system	Yes
Anti-leak	Yes
Temperature control	Adjustable
Cord guard	360° swivel
Indicator light	Yes
Safety	Do not immerse, unplug before refilling, do not leave unattended
Care and cleaning	Clean with a damp cloth, do not use solvents or corrosive products
Spare parts and repairability	Contact an authorized service center, do not disassemble yourself

Frequently Asked Questions - SSI 2874 SINBO

How to fill the water tank?

Unplug the iron, set the steam button to dry, then fill through the opening with tap water or demineralized water if the water is hard. Do not store with water.

Why does smoke come out during first use?

This is normal: manufacturing oils are burning. Let it run empty for 10 minutes until it disappears.

How to use the steam shot?

Set the temperature to maximum (max symbol), wait until the indicator light turns off, then press the steam shot button. Do not perform more than 3 consecutive shots to avoid cooling.

What to do if the iron does not produce steam?

Check that the tank has enough water (at least 1/4), that the steam button is not set to 0, and that the temperature is set to a steam position (• • •). Wait for preheating.

Why does water drip under the iron?

This can happen if the temperature is too low to vaporize. Make sure to set the iron to a sufficient temperature. The anti-drip system activates automatically at low temperature.

How to clean the iron?

Unplug it and let it cool. Clean the soleplate and body with a damp cloth. Never use solvents or abrasive products.

Can I use descaling agents or perfumes?

No. The use of chemical additives, perfumes, or non-recommended descaling agents voids the warranty. Use only tap water or demineralized water.

How to adjust the temperature according to the fabric?

Turn the temperature dial according to the symbols: • for nylon/acetate (low), •• for wool/silk (medium), ••• for cotton/linen (high). Start with delicate fabrics.

What to do if the spray function does not work?

Make sure the tank contains at least 1/4 water. Press the button several times to prime the pump. The iron can be in vertical or horizontal position.

How to use vertical steam?

Fill the tank, set the temperature to maximum, wait for preheating. Hold the iron vertically and press the steam shot button to de-wrinkle hanging clothes.

USER MANUAL SSI 2874 SINBO

Labeled diagram of a steam iron with numbered parts for identification

Değerli Müsterimiz,

Children being supervised not to play with the appliance.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliances by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Heat caused by the arrival of the cutter accidentally starting position to avoid a hazard, such as a timer, this device

is fed via an external switching scheme on a regular basis or by means of the utility opened and closed, and a circuit connected to the circuit

Hot or cold iron and cords should be out of reach of children under 8 years.

SINBO SSI 2874 ÇOK FONKSİYONLU BUHARLI ÜTÜ KULLANIM TALİMATI AC230V, 50Hz, 2200W

IMPORTANT SAFETY INSTRUCTIONS

When using your flatiron, basic safety precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING

1. Use iron only for its intended use.
2. To protect against a risk of electric shock, do not immerse the iron in water or other liquids.
3. The iron should always be turned to "min",?before plugging or unplugging from outlet. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.

4. Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing.

5. Always disconnect iron from electrical outlet when filling with water or emptying and when not in use.

6. Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron. Take it to a qualified serviceman for examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used.

7. Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while connected or on an ironing board.

8. Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside down – there may be hot water in the reservoir.

9. If the malfunction indicator goes on, the flatiron is not operating normally. Disconnect from the power supply and have the flatiron serviced by qualified service personnel.

10. The iron must be used and rested on a stable surface.

11. The iron is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking.

12. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

13. Children should be supervised to ensure that they do not play with appliance.

14. The iron must not be left unattended while it is connected to the supply mains;

15. The plug must be removed from the socked-outlet before the water reservoir is filled with water;

16. When placing the iron on its stand, ensure that the surface on which the stand is placed is stable;

17. The iron is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking.

18. If the supply cord is damaged it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

SPECIAL INSTRUCTIONS

1. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.
2. If an extension cord is absolutely necessary, a 10-ampere cord should be used. Cords rated

for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over.

SAVE THESE INSTRUCTIONS

More specifically:

• DO NOT let children or untrained persons use the appliance without supervision.
• NEVER immerse the iron, cable or plug in any liquid.
• DO NOT leave the hot iron touching fabrics or very inflammable surfaces.
• DO NOT leave the appliance unnecessarily plugged in. Disconnect the plug from the mains when the appliance is not being used.
• NEVER touch the appliance with wet or damp hands.
• DO NOT use the power cord or the appliance in order to pull the plug out of the socket.
• DO NOT leave the appliance exposed to the weather (rain, sun, etc.).
• DO NOT leave the iron without supervision when it is connected to the power supply.
• DO NOT fill the reservoir with water before removing the plug from the socket.

PLEASE NOTE!

Do not use chemical additive, scented substances or decalcifiers. Failure to comply with the above-mentioned regulations leads to the loss of guarantee.

SPECIFICATIONS

* Ceramic soleplate
* Dry/spray/steam/burst of steam/vertical steam
* Self-cleaning/anti-drip function
* Variable steam control
* 360 degree swivel cord guard with indicate light
* Adjustable temperature control
* Water tank capacity: 380ml
* Continue steam rate: 110g/minute
* Steam burst: 96g
* Spray volume:0.65g/time
* AC230V 50Hz, 2200W

DESCRIPTION OF DEVICE

1. Soleplate, 2. Skirt, 3. Tank Cover, 4. Spray Nozzle, 5. Water Cover, 6. Steam Knob, 7. Burst Button, 8. Spray button, 9. Lamp, 10. Up Cover, 11. Handle, 12. Cord Protector, 13. Rear Cover, 14. Temperature Knob, 15. Tank, 16. Self Clean Button

ANTI-DRIP SYSTEM

With the anti-drip system, you can perfectly iron even the most delicate fabrics.

Always iron these fabrics at low temperatures. The plate may cool down to the point where no more steam comes out, but rather drops of boiling water that can leave marks or stains. In these cases, the Anti-drip system automatically activates to prevent vaporization, so that you can iron the most delicate fabrics without risk of spoiling or staining them.

GENERAL INSTRUCTIONS

When using the iron for the first time, you may notice a slight emission of smoke and hear some sounds made by the expanding plastics. This is quite normal and it stops after a short time. We also recommend passing the iron over an ordinary cloth before using it for the first time.

Suggestions before using the iron for the first time

1. Certain parts of the iron have been lightly greased therefore the iron could give off a little smoke when plugged in for the first time. This will cease after a short while.
2. Before using the iron for the first time, remove the plastic protector from the base (if it has one) clean the base with a soft cloth.
3. Keep the base very smooth. Do not run it over metal objects (such as against the ironing board, buttons, zips etc.)
4. Pure wool fibres (100% wool) can be ironed with the appliance in the steam position by preference, select a high steam position and use a dry ironing cloth.

Selecting the temperature

1. Check the ironing instructions on the garment to be ironed.
2. If the garment does not have any ironing instructions but you know the kind of fabric in question, use the chart below.
3. Fabrics that have some kind of finish (polishing, wrinkles, contrasts....) can be ironed at the lowest temperatures.
4. If the fabric contains several kinds of fibres, always select the temperature applicable, if an article contains 60% polyester and 40% cotton, you must always choose the temperature corresponding to polyester and without steam.
5. First classify the articles to be ironed according to the most suitable ironing temperature: wool with wool, cotton with cotton, etc. as the iron heats up as fast as it cools, start by ironing the articles requiring the lowest temperature such as those made of synthetic fibres. Progress towards those that require the highest temperatures.
6. Turn the temperature control until it is in front of the appropriate signal according to the following:

• position for nylon and acetate

• position for wool, silk or mixures

• • • position for cotton or linen (steam).

How to fill the water tank

1. Unplug the iron.
2. Set the steam ruler to dry ironing.
3. Fill the tank through the filling hole.
4. If you have hard water, it is advisable to use only distilled or demineralized water.
5. do not use chemically de-limed water or perfumed
6. Do not store the iron with water in the tank.

Steam ironing

1. Fill the iron as described in the section "how to fill the water tank".
2. Plug the iron into the mains.
3. Steam ironing is only possible when the highest temperatures shown on the temperature control are selected.

Otherwise, water may escape through the soleplate.

1. Wait until the pilot light goes out, which indicates that the selected temperature has been reached.
2. Turn the steam button to the required position.
3. When the ironing is finished and during breaks in ironing place the iron in its upright position.
4. Disconnect the iron from the mains supply. Pour of any remaining water and leave the iron to cool off.

Spray

1. The spray can be used in any position, either in dry or steam ironing, as long as the water tank is filled with water.
2. Press the spray button for this function

NOTE: This button has to be pressed repetitively to start this function for the first time.

Shot of steam

Shot of steam give extra steam for removing persistent wrinkles.

1. Place the temperature selector at the "max" position and wait until the pilot light goes out
2. Wait for a few seconds for the steam to penetrate the fibre before pressing again.

NOTE: For the best steam quality, do not use more than three successive bursts each time. Several pumping actions are needed to start this function.

Excessive use of this feature will cause the iron to cool, ensure that the pilot light is out, before operating the shot of steam control

Cleaning

1. Disconnect the appliance from the mains, before cleaning.
2. Do not use solvents or abrasive products to clean the iron, clean with a damp cloth.

Defects and repairs

Do not attempt to replace a defective mains lead. The appliance has to be returned to an authorized service centre for repair.

Faults-reasons and solutions

Iron emits an odor or smoke

Iron gives off an odor when turned on for the first time. Oils used during manufacture need to be burnt off allow ten minutes for odor to disappear.

Iron does not heat

The iron should be plugged into a 230Volt, AC electrical outlet only. The temperature dial must be set at the desired temperature.

Iron does not steam

The water tank many be empty. Turn the steam valve to "0" and add water. Allow the iron to heat, and then set the steam dial to the steam setting.

Burst of steam feature does not work

The water tank must be at least 1/4 full. Temperature must be set to steam position. Iron should be in the horizontal position. Prime pump briefly. Allow a short pause between shots. Be sure to fully depress the burst of steam button.

Spray mist feature does not work

The water tank must be at least 1/4 full. Fill the iron as described in the section "how to fill the water tank".

Iron is leaking

The variable steam dial must be set on "", until the iron is hot. The temperature setting is too low to produce steam. Shot of steam used too much, allow iron to re-heat.

FRANÇAIS

SINBO SSI 2874 FER À REPASSER À VAPEUR MULTI-FONCTION MODE D'EMPLOI

230V AC, 50Hz, 2200W

CONSIGNES IMPORTANTES DE SÉCURITÉ

United Favour Development Limited

Unit B, 10/F Lee May Building 788-790

Nathan Road, Mongkok, Kowloon, HK.

- UYGUNLUK BEYANI / CE CONFORMITY - TÜV Austria Cert GmbH

A-1015 Wien, Krugerstraße 16 Austria