00260 - Vacuum Cleaner Maxxmee - Free user manual and instructions

USER MANUAL 00260 Maxxmee

Items Supplied 8 At A Glance 8 Symbols 9 Signal Words 9 Intended Use 9 Safety Notices 10 Safety Devices 11 Tips and Notes 12 Use 12 Cleaning and Storage 12 Troubleshooting 13 Disposal 14 Technical Data 14 ITEMS SUPPLIED

• Operating instructions 1 x Check the items supplied for complete- ness and the components for transport damage. If you fi nd any damage, do not use the device but contact our customer service department. Remove any possible fi lms, stickers or transport protection from the device. Never remove the rating plate and any possible warnings!

Possible dirt residues in the dust container can be attributed to quality checks and do not consti- tute a defect with the device.

(Picture A) 1 On / Off switch 2 Ventilation slots 3 Motor unit 4 Dust container 5 Handle (Picture B) 6 Roller 7 UV-C lamp cover 8 Safety switch, right 9 Vibration head 10 Suction opening 11 Safety switch, left 12 UV-C lamp (under the cover)Dust mite vacuum cleaner

SYMBOLS Danger symbols: These symbols indicate possible hazards. Read the associated safety notices carefully and follow them. Supplementary information Read operating instructions before use.

Protection class II SIGNAL WORDS Signal words indicate hazards if the asso- ciated notices are not followed. DANGER – high risk, results in serious injury or death WARNING – medium risk, may result in serious injury or death CAUTION – low risk, may result in minor or moderate injury NOTICE – may result in risk of damage to material INTENDED USE ■ This device is intended to be used to kill off bacteria and remove dust, germs and domestic dust mites. It is suitable for use on mattresses, bed sheets, bed covers, upholstered furniture and similar items. On no account should the device be used to suck up the following: ○ liquids or wet substances (e.g. wet carpet shampoo) ○ glowing ash, cigarette ends, matches, etc. ○ infl ammable or explosive substances ○ very fi ne dust (e.g. concrete dust), ash or toner ○ pointed, hard objects such as large pieces of broken glass ■ The device is for personal use only and is not intended for commercial applications. ■ The device should only be used as described in the operating instruc- tions. Any other use is deemed to be improper. ■ The warranty does not cover faults caused by incorrect handling, dama- ge, assembly or attempted repairs. The same applies to normal wear and tear. Dear Customer, We are delighted that you have chosen the MAXXMEE dust mite vacuum cleaner. It not only removes dust and dirt from mattresses, pillows, blankets and upholstered furniture, but at the same time sterilises the surfaces using UV-C light.If you have any questions about the device and about spare parts / accessories, contact the custo- mer service department via our website: www.dspro.de/kundenservice We hope you have a lot of fun with your MAXXMEE dust mite vacuum cleaner. Information About the Operating Instructions Before using the device for the fi rst time, please read through these operating inst- ructions carefully and keep them for future reference and other users. They form an integral part of the device. The manufacturer and importer do not accept any liability if the information in these operating instructions is not complied with.EN

WARNING: Note all safety notices, instructions, illustra-

tions and technical data provided with this device. Failure to follow the safety notices and instructions may result in electric shock, fi re and / or injuries. ■ This device must not be used by children. The device and the connection are to be kept away from children. ■ This device may be used by people with reduced physical, sensory or mental abilities or a lack of experience and / or knowledge if they are supervised or have received instruction on how to use the device safely and have understood the dangers resulting from this. Children must not play with the device. ■ The device must always be disconnected from the mains po- wer when it is left unattended and before assembling, disas- sembling or cleaning the device. ■ Never immerse the device or the connection in water or other liquids and ensure that they cannot fall into water or become wet. ■ In the interest of your own safety, you should inspect the de- vice for damage each time before you use it. The device may only be used if it has no visible signs of damage! If the device or the connection of the device is damaged, it must be repla- ced by the manufacturer, customer service department or a similarly qualifi ed person (e. g. specialist workshop) in order to avoid any hazards. DANGER – Danger of Electric Shock ■ Use and store the device only in closed rooms. ■ Do not use or store in rooms with high humidity. ■ If the device falls into water while it is connected to the mains power, pull the plug out of the plug socket im- mediately! Only after this should you pull the device out of the water. ■ Never touch the device and the con- necting cable with wet hands when the device is connected to the mains power. WARNING – Danger of dama- ge to the eyes and skin! ■ Germicidal ultraviolet rays are harmful to the eyes and skin. Never expose yourself or other people and animals to direct or refl ected rays! IfDust mite vacuum cleaner

you come into contact with the rays, consult a doctor immediately. ■ Make sure that the safety switches of the UV-C lamp are not blocked! WARNING – Danger of Injury ■ Keep children and animals away from plastic bags and fi lms. There is a danger of suffocation. ■ Make sure that the connecting cable is always kept out of the reach of small children and animals. There is a danger of strangulation. ■ Lay the connecting cable in such a way that it does not present a trip hazard. ■ Keep animals, hair, jewellery, wide clothing, fi ngers and all other body parts away from the suction opening of the device. They could become stuck to the device. WARNING – Danger of Fire! ■ Do not cover the device during operation in order to prevent it from catching fi re. Do not insert anything into the openings of the device and make sure that these do not become clogged. NOTICE – Risk of Damage to Material and Property ■ Only connect the device to a plug socket that is properly installed and matches the technical data of the device. The plug socket must also be readily accessible after connection so that the connection to the mains can quickly be isolated. ■ Only use suitable extension cables whose technical data is the same as that of the device. ■ Make sure that the connecting cable is not squashed, bent or laid over sharp edges and does not come into contact with hot surfaces. ■ The device must be switched off when inserting or removing the mains plug. ■ Pull the mains plug out of the plug socket if an error occurs during ope- ration or before a thunderstorm. ■ Always pull the mains plug and never the mains cable to disconnect the device from the mains power. Never pull or carry the device by the mains cable. ■ Protect the device from heat, naked fl ames, sub-zero temperatures, per- sistent moisture, wet conditions and impacts. ■ Do not try to lubricate the rollers with lubricant or oil. This would cause dust and dirt to increasingly adhere to the rollers. ■ Use only original accessories from the manufacturer in order to guarantee that there is no interference that may prevent the device from working and to avoid possible damage. ■ Do not lay heavy objects on the de- vice or the connecting cable. SAFETY DEVICES The device has two safety switches (8, 11). The UV-C lamp (12) only switches on if both safety switches are pressed into the motor unit (3) (automatic switch-off function of the UV-C lamp deactivated). This happens automatically when the device is placed on a fl at surface. If the safety switches lose contact with the surface below, the automatic switch-off function is activated and the UV-C lamp stops being lit (automatic switch-off function of the UV-C lamp activated).EN

• Always clean mattresses on both sides.

• We recommend cleaning new mat- tresses once a month. Older mattres- ses should initially be cleaned every day for a week. We then recommend cleaning them once a month.

• The fi lter should be replaced every 12 – 18 months; the UV-C lamp (12) should be replaced every 12 – 24 months. If you have any questions about spare parts, please contact the customer service department via our website: www.dspro.de/kundenservice USE Please Note! ■ The device should only be used if it has been fully and correctly assem- bled! The dust container and the fi lter must be inserted and must not be damaged! If the dirt were to get inside the motor unit, this could damage the motor. ■ Make sure that the safety switches of the UV-C lamp are not blocked!

1. Insert the mains plug into a properly

installed plug socket that is easily accessible.

2. Place the device down fl at on the

surface which is to be cleaned.

3. Press the On / Off switch (1) to switch

on the device. The device starts to vacuum and the UV-C lamp (12) and the vibration head (9) switches on.

The vibration shakes up the surface which is to be cleaned and the dust which is agitated is sucked in through the suction opening (10).

4. Guide the device very slowly and

evenly over the surface to be clea- ned.

5. After vacuuming, press the On / Off

switch to switch off the device.

6. Remove the mains plug from the plug

CLEANING AND STORAGE

Please Note! ■ Empty the dust container each time after you use the device. The fi lter must also be regularly cleaned in order to prevent overloading of the motor. ■ Do not use any sharp or abrasive cleaning agents to clean the device and accessories. They may damage the surfaces. ■ CAUTION – Danger of Burns! The UV-C lamp will become hot during use. Allow the UV-C lamp to cool suffi ciently after using the device.

• Make sure that the mains plug has been pulled out and the device is disconnected from the power.

• As required, wipe down the motor unit with a damp soft cloth. Then dry it with a soft cloth.

• Wipe out the recess for the dust con- tainer (4) with a duster. Cleaning the Dust Container and HEPA Filter

1. Reach into the recess in the dust

container (4) and pull it up and out of the motor unit (3).

2. Pull the HEPA-fi lter out of the dust

4. Wipe out the dust container with a

5. Tap out the HEPA-fi lter and clean it

with a soft brush if necessary.

For thorough cleaning the fi lter can be rinsed under cold (!) run- ning water. NOTE: Allow the HEPA-fi lter to dry completely before the device is reas- sembled.

6. Insert the HEPA-fi lter into the dust

7. Insert the dust container into the

motor unit. It must audibly click into place. Cleaning the UV-C Lamp

1. Undo the two screws on the cover (7)

of the UV-C lamp (12) and take off the cover.

2. Wipe down the UV-C lamp with a dry

duster. NOTE: Make sure that you do not touch the UV-C lamp with your fi ngers!

3. Place the cover back on and fi x it in

place with the two screws. Removing the UV-C lamp Carefully lift the UV-C lamp (12) and disconnect it from the contacts. When you fi t a new UV-C lamp, fi rst insert it into a contact and place it some way into the recess before inserting it into the second contact. NOTE: Make sure that you do not touch the UV-C lamp with your fi ngers! Storage

• Store the device in a cool, dry place which is protected from direct sunlight and is out of the reach of children and animals. TROUBLESHOOTING If the device does not work properly, check whether you are able to rectify the problem yourself. If the problem cannot be solved with the steps below, contact the customer service department. Do not attempt to repair an elec- trical device yourself! The device generates no suction. The mains plug is not inserted correctly in the plug socket. ► Correct the fit. The plug socket is defective. ► Try another plug socket. There is no mains voltage. ► Check the fuse of the electrical dis- tributor (fuse box). The device is not switched on. ► Press the On / Off switch (1). Low suction force. The dust container (4) is too full. ► Empty the dust container. The fi lters are dirty. ► Clean the filters. The suction opening (10) is blocked. ► Switch off the device, pull the mains plug out of the plug socket and remove the blockage. The UV-C lamp (12) does not light up. The automatic switch-off function of the UV-C lamp has been activated. ► Check the safety switches (see the “Safety Devices” chapter). Unusual odour The device is being used for the fi rst time. ► A new odour is normal when the device is used for the first time; it disappears after a while.EN

DISPOSAL Please Note! ■ The UV-C lamp should be removed prior to disposal of the device and disposed of separately from the device. Notes on how to remove the UV-C lamp can be found in the “Cleaning and Storage” chapter – “Removing the UV-C Lamp”. Dispose of the packaging mate- rial in an environmentally friendly manner so that it can be recyc- led. This device is governed by the European Directive 2012/19/EU on waste electrical and electro- nic equipment (WEEE). Do not dispose of the device as normal domestic waste, but rather in an environmentally friendly manner via an offi cially approved waste disposal company. TECHNICAL DATA Article number: 00260 Model number: MC619P Voltage supply: 220 – 240 V ~ 50 / 60 Hz Power: max. 300 W Protection class: II ID of operating instructions: Z 00260 M DS V1 0720 uh All rights reserved.Aspirateur anti-acariens