KE6330.0SR - Cooker Küppersbusch - Free user manual and instructions

Type	KE6330.0SR
Brand	Küppersbusch
Total power	7000 W
Number of zones	4
Energy consumption of the table	75 Wh/kg (class A)
Left front zone	2200/1000 W, Ø 220/145 mm
Left rear zone	1200 W, Ø 155 mm
Right rear zone	2400/1500 W, Ø 265 x 180 mm
Right front zone	1200 W, Ø 155 mm
Installation dimensions (W x D x H)	598 x 518 x 44 mm
Power supply	230 V ~ 50 Hz or 400 V ~ 2 phases + N
Control type	Touch controls with slider
Functions	Timer, keep warm, automatic cooking, pause, memory, lock, operating time limitation
Safety	Control panel lock, residual heat indicator, automatic shutdown, overheat detection
Cleaning	Water and dish soap, avoid abrasive products
Installation	Built-in, sealing gasket supplied

Frequently Asked Questions - KE6330.0SR Küppersbusch

How to turn on the hob?

Press the on/off key [ ]. Then, select a cooking zone by touching the corresponding slider, then slide your finger on the slider to set the power from 1 to 9.

What to do if the [E] symbol appears?

The [E] symbol indicates an electronic fault. Disconnect the hob from the mains, wait a few moments, then reconnect. If the symbol persists, contact after-sales service.

How to use the keep warm function?

Select the desired cooking zone. Slide the slider between positions 0 and 1 until the display shows [U]. The temperature will automatically be maintained at 70°C. To deactivate, slide the slider to a higher power.

How to lock the control panel?

To lock, keep one finger on the [ ] key (on/off) and press the [ ] key 3 times. The display shows [L]. To unlock, repeat the same operation.

How to set the timer?

Select the cooking zone and set the power. Press the timer key [ ], then slide on the slider to set the time from 1 to 99 minutes. The countdown starts automatically. At the end of cooking, [00] flashes and an audible signal sounds.

What to do in case of a crack in the ceramic glass?

Immediately cut off the power supply to the appliance. Do not touch the surface and contact after-sales service for repair. Do not use the appliance until it is repaired.

How to clean the hob?

Wait for the hob to cool down. Clean with a damp cloth with a little dish soap or a special ceramic glass cleaner. Do not use abrasive sponges, scouring powders, or sharp objects. Wipe with a clean cloth.

How to activate automatic cooking?

Select a cooking zone, slide the slider to level 7, then keep your finger pressed for 3 seconds until [7] flashes with [A]. The zone heats at full power, then automatically reduces.

How to recall the last settings (memory function)?

After turning off the hob, press the on/off key [ ]. While the display flashes, press the [ ] key before the end of the flashing. The previous settings (power, timer, auto cooking) are restored.

What does the [L] symbol on the display mean?

The [L] symbol indicates that the control panel is locked (child safety). To unlock, keep one finger on the [ ] key and press the [ ] key 3 times. The symbol disappears.

USER MANUAL KE6330.0SR Küppersbusch

Please read the users and installation instructions carefully before installation of the appliance and before starting to use it.

Thank you for having chosen a KUPPERSBUSCH ceramic hob

In order to install properly your appliance and to make the best use of it, please read this entire instruction manual carefully.

SUMMARY

SAFETY 20

PRECAUTIONS BEFORE USING 20
USING THE APPLIANCE 20
PRECAUTIONS NOT TO DAMAGE THE APPLIANCE 21
PRECAUTIONS IN CASE OF APPLIANCE FAILURE 22
OTHER PROTECTIONS 22

DESCRIPTION OF THE APPLIANCE 23

TECHNICAL DATA 23
CONTROL PANEL 23

USE 24

SENSITIVE TOUCHES 24
DISPLAY 24
RESIDUAL HEAT INDICATION 24
"SLIDER" ZONE: TO SET POWER AND TIMER VALUES 24

STARTING-UP AND APPLIANCE MANAGEMENT 24

BEFORE USING YOUR NEW HOB 24
STARTING-UP 25
EXTENSION ZONE 25
TIMER 25
KEEP WARM FUNCTION 26
AUTOMATIC COOKING 26
PAUSE FUNCTION 26
RECALL FUNCTION 27
CONTROL PANEL LOCKING 27
OPERATING TIME 27

COOKING ADVICES 28

EXAMPLES OF POWER SETTING 28

MAINTENANCE AND CLEANING 28

WHAT TO DO IN CASE OF A PROBLEM 28

ENVIRONMENT PROTECTION 29

INSTALLATION INSTRUCTIONS 30

ELECTRICAL CONNECTION 31

Precautions before using

• Unpack all the materials.
• The installation and connecting of the appliance have to be done by approved specialists. The manufacturer cannot be responsible for damage caused by building-in or connecting errors.
• To be used, the appliance must be well-equipped and installed in a kitchen unit and an adapted and approved work surface.
• This domestic appliance is exclusively for the cooking of food, to the exclusion of any other domestic, commercial or industrial use.
• Remove all labels and self-adhesives from the ceramic glass.
• Do not change or alter the appliance.
• The cooking plate cannot be used as freestanding or as working surface.
• The appliance must be grounded and connected conforming to local standards.
• Do not use any extension cable to connect it.
• The appliance cannot be used above a dishwasher or a tumble-dryer: steam may damage the electronic appliances.
• The appliance is not intended to be operated by means of external timer or separate remote control system.

Using the appliance

• Switch the heating zones off after using.
• Keep an eye on the cooking using grease or oils: that may quickly ignite.
• Be careful not to burn yourself while or after using the appliance.
• Make sure no cable of any fixed or moving appliance contacts with the glass or the hot saucepan.
• Magnetically objects (credit cards, floppy disks, calculators) should not be placed near to the engaged appliance.

• Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot.

• In general do not place any metallic object except heating containers on the glass surface. In case of untimely engaging or residual heat, this one may heat, melt or even burn.

• Never cover the appliance with a cloth or a protection sheet. This is supposed to become very hot and catch fire.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.

Precautions not to damage the appliance

• Raw pan bottoms or damaged saucepans (not enamelled cast iron pots,) may damage the ceramic glass.
• Sand or other abrasive materials may damage ceramic glass.
• Avoid dropping objects, even little ones, on the vitroceramic.
• Do not hit the edges of the glass with saucepans.
• Make sure that the ventilation of the appliance works according to the manufacturer's instructions.
• Do not put or leave empty saucepans on the vitroceramic hobs.
• Sugar, synthetic materials or aluminium sheets must not contact with the heating zones. These may cause breaks or other alterations of the vitroceramic glass by cooling: switch on the appliance and take them immediately out of the hot heating zone (be careful: do not burn yourself).
• WARNING: Danger of fire: do not store items on the cooking surface.
• Never place any hot container over the control panel.
• If a drawer is situated under the embedded appliance, make sure the space between the content of the drawer and the inferior part of the appliance is large enough (2 cm). This is essential to guaranty a correct ventilation.
• Never put any inflammable object (ex. sprays) into the drawer situated under the vitroceramic hob. The eventual cutlery drawers must be resistant to heat.

Precautions in case of appliance failure

• If a defect is noticed, switch off the appliance and turn off the electrical supplying.
• If the ceramic glass is cracked or fissured, you must unplug the appliance and contact the after sales service.
• Repairing has to be done by specialists. Do not open the appliance by yourself.
• WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of electric shock.

Other protections

• Note sure that the container pan is always centred on the cooking zone. The bottom of the pan must have to cover as much as possible the cooking zone.
• For the users of pacemaker, the magnetic field could influence its operating. We recommend getting information to the retailer or of the doctor.
• Do not to use aluminium or synthetic material containers: they could melt on still hot cooking zones.
• NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.

Technical data

Type KE6330.0SR
Total power 7000 W Energy consumption for the hob EChob** 175	Wh/kg
Front left heating zone Nominal power 2200 / 1000 W Standardised cookware category** C Energy consumption ECw** 171.1 Wh/kg	Ø 220/145 mm
Rear left heating zone Nominal power 1200 W Standardised cookware category** A Energy consumption ECw** 173.8 Wh/kg	Ø 155 mm
Rear right heating zone Nominal power 2400 / 1500 W Standardised cookware category** D Energy consumption ECw** 181.3 Wh/kg	Ø 265 x180 mm
Front right heating zone Nominal power 1200 W Standardised cookware category** A Energy consumption ECw** 173.8 Wh/kg	Ø 155 mm

** calculated according to the method of measuring performance (EN 60350-2).

Control panel

Sensitive touches

Your ceramic hob is equipped with electronic controls with sensitive touch keys. When your finger touches the key, the corresponding command is activated. This activation is validated by a control light, a letter or a number in the display and/or a "beep" sound.

Touch only one key on the same time.

Display

Display Designation Function

0	Zero	the heating zone is activated
1...9	Power level	Selection of the cooking level
A	Heat accelerator	automatic cooking
E	Error message	Electronic failure
H	Residual heat	the heating zone is hot
U	Keep warm	Maintain automatically of 70°C.
II	Pause	the hob is in pause

Residual heat indication

After the switch-off of the hob, the heating zone is still hot and indicates [H] on the display. The symbol [H] disappears when the heating zone may be touched safely. When the residual heat indicator light is on, don't touch the heating zone and don't put any heat sensitive object on them. There are risks of burn and fire!

"SLIDER" zone: to set power and timer values

Select the cooking zone. The display corresponding to the selected zone will be highlighted. While the zone is activated (for a few seconds), you can adjust the power by sliding your finger on the groove of the glass (Slider). Slide clockwise to increase the power level and counterclockwise to decrease the power level. To adjust the power of another cooking zone, wait until the previous zone is no longer activated (the highlighted display becomes normal).

STARTING-UP AND APPLIANCE MANAGEMENT

Before using your new hob

Clean your hob with a damp cloth, and then dry the surface thoroughly. Do not use detergent which risks causing blue-tinted colour on the glass surface.

Starting-up

- Start-up/ switch off the hob

Action	Control panel	Display
To start	press the key [ ]	[0]
To stop	press the key [ ]	nothing or [H]

- Start-up/ switch off a heating zone

Action Control panel Display

Zone selection Press on the "SLIDER"

across from the desired zone [0]

Select the power level Slide on the "SLIDER" [1] to [9]

To stop Slide to [0] on "SLIDER" [0] or [H]

If no action is made within 20 second the electronics returns in waiting position.

Extension zone

Action Control panel Display

Zone selection Press on the "SLIDER" across from the desired zone [0]

Select the power level Slide on the "SLIDER" [1] to [9]

Switch on the extension zone press key [ ] Extension zone

Select the power level Slide on the "SLIDER" [1] to [9]

Switch off the extension zone press key [ ] Extension zone

light is on

light is off

Timer

The timer is able to be used simultaneous with all heating zones and this with different time settings (from 1 to 99 minutes) for each heating zone.

- Setting and modification of the cooking time :

Action Control panel Display

Zone selection Press on the "SLIDER"

across from the desired zone [0]

Select the power level Slide on the "SLIDER" [1] to [9]

Set the « Timer » Press on the [ ] to increase of ten [10, 20, 30...] Slide on the "SLIDER" [31, 32, 33...]

The time is confirmed and the cooking starts.

- To stop the cooking time:

Action Control panel Display

Zone selection	Press on the “SLIDER”
	across from the desired zone	time remaining
Select the timer	Press on the [◎]	time remaining
Stop the timer	Press on the [◎]	[00]

Automatic stop at the end of the cooking time:

As soon as the selected cooking time is finished, the timer displays blinking [00], a sound rings and the heating zone stops.

To stop the sound and the blinking it is enough to press the timer key [ ].

- Egg timer function:

Action

Control panel

Display

To start

press the key [ ]

[0]

[00]

Select « Timer »

Set the « Timer »

Press on the [

Increase of ten

[10, 20, 30...]

Slide on the "SLIDER" [31, 32, 33...]

After a few seconds, the timer display stops blinking.

press on the "SLIDER"

between the [0] and the [1] [U]

To stop

Slide on the "SLIDER"

[0]to[9]

Automatic cooking

All the cooking zones are equipped with an automatic cooking device. The cooking zone starts at full power during a certain time, and then reduces automatically its power on the preselected level.

Start-up

Action

Control panel

Display

Power level selection

Slide to the position [ 7 ] and stay 3s

[7] Is blinking

(For example « 7 »)

with [A]

- Switching off the automatic cooking

Action

Control panel

Display

Power level selection

Slide on the "SLIDER" [0] to [9]

Selected power	Automatic cooking time (Min:S)
1	00:48
2	02:24
3	03:36
4	05:24
5	06:48
6	02:00
7	02:48
8	03:36
9	- - -

Pause function

This function brakes the entire hob's cooking activity and allows restarting with the same settings.

- Start up / Stop the pause function

Action

Control panel

Display

Engage Pause

Press [ ] key 3s.

displays [II] in

Stop the Pause

Press [ ] key 3s.

and on the slider

Last settings

the heating zone displays

Recall Function

After switching off the hob ( it is possible to recall the last settings.

• cooking stages of all cooking zones (power)
• minutes and seconds of programmed cooking zone-related timers
• Heat up function

The recall procedure is following:

Press the key [
- Then press the key [ within 6 seconds

The precedent settings are activated.

Control panel locking

To avoid modifying a setting of cooking zones, in particular with within the framework of cleaning the control panel can be locked (with exception to the On/Off key [9]).

• Locking

Action

Control panel

Display

To start

press the key [ ]

[0] or [H]

Hob locking

Hold a finger on the [ ]

and press 3 times on the [ [L]

• Unlocking

Action

Control panel

Display

To start

press the key [ ]

[L]

Unlocking the hob

Hold a finger on the [ ]

and press 3 times on the [ [0] or [H]

Operating time

Each cooking zone is equipped with an operating time limitation: the cooking zone is automatically switched off after a certain time without any change of settings. This time is varying according to the selected power level as described in the table below.

Power level	Max operating time (hours)
1	6
2	6
3	5
4	5
5	4
6	1,5
7	1,5
8	1,5
9	1,5

Examples of power setting

(The values below are indicative)

1 to 2	Melting Reheating	Sauces, butter, chocolate, gelatine Dishes prepared beforehand
2 to 3	Simmering Defrosting	Rice, pudding, sugar syrup Dried vegetables, fish, frozen products
3 to 4	Steam Vegetables, fish, meat
4 to 5	Water	Steamed potatoes, soups, pasta, fresh vegetables
6 to 7	Medium cooking, Simmering	Meat, liver, eggs, sausages, pancakes
7 to 8	Cooking Potatoes, fritters, waffles
9	Frying, roasting, Boiling water	Steaks, omelettes, fried dishes, water

MAINTENANCE AND CLEANING

Switch-off the appliance before cleaning.

Do not clean the hob if the glass is too hot because they are risk of burn.

• Remove light marks with a damp cloth with washing up liquid diluted in a little water. Then rinse with cold water and dry the surface thoroughly.
• Highly corrosive or abrasive detergents and cleaning equipment likely to cause scratches must be absolutely avoided.
• Do not ever use any steam-driven or pressure appliance.
• Do not use any object that may scratch the ceramic glass.
• Ensure that the pan is dry and clean. Ensure that there are no grains of dust on your ceramic hob or on the pan. Sliding rough saucepans will scratch the surface.
• Spillages of sugar, jam, jelly, etc. must be removed immediately. You will thus prevent the surface being damaged.

WHAT TO DO IN CASE OF A PROBLEM

The hob or the cooking zone doesn't start-up:

• The hob is badly connected to the electrical system.
• The protection fuse has blown.
• The locking function is activated
• The sensitive keys are covered by grease or water.
• An object is covering the control panel.

The symbol [E] displays :

• Call the After-sales Service.

One or all cooking zones cut-off:

• The safety system has engaged
• You forgot to cut-off the cooking zone for a long time.
  One or more sensitive keys are covered.
• The pan is empty and has overheated.

The automatic cooking system « go and stop » doesn't start-up:

• The cooking zone is still hot [H]
  The highest power level is set [9]

The symbol [U] displays :

Refer to the chapter "keep warm".

The symbol [II] displays :

Refer to the chapter "Pause".

The symbol [ L ] displays :

Refer to the chapter control panel locking page.

The control panel displays [Er03]:

• An object or liquid covers the control keys. The symbol disappear as soon as the key is released or cleaned.

The control panel displays [ER21]:

• The hob is overheated, let it cool and then turnit on again.

The control panel displays [U400], [Er25] or [U4]:

• The hob is not connected to the network. Check the connection and reconnect the hob.

If one of the symbols above persists, call the SAV.

ENVIRONMENT PROTECTION

• The packaging material is ecological and can be recycled.
• The worn appliances contain certain noble metals. Apply to the local government about the possibilities of recycling.

• Don't dispose of your appliance with general household waste
• Get in touch with the waste collection centre of your local council that control the recycling of household appliances.

INSTALLATION INSTRUCTIONS

The installation must be performed by a qualified electrical contractor. This contractor will take the entire responsibility of the installation. The installation has to comply with the legislation and the standards in force in your country.

How to stick the gasket:

The gasket supplied with the hob prevents the intrusion of liquids into the cabinet below. Its installation has to be done carefully, as described below.

Stick the gasket (2) two millimeters from the external edge of the glass, after removing the protection tape (3).

Fitting - installing:

• Cut out sizes of the worktop:

A B E F H
KE6330.0SR	598 mm	518 mm	560 mm	490 mm	44 mm

• Ensure that there is a distance of 50 mm between the hob and the wall or sides.

• The hobs are classified as "Y" class for heat protection. Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear and tall units or a wall at one side. On the other side, however, no unit or divider must stand higher than the hob.

• The piece of furniture or the support in which the hob is to be fitted, as well as the edges of furniture, the laminate coatings and the glue used to fix them, must be able to resist temperatures of up to 75^ .

• The mural rods of edge must be heat-resisting.
• Not to install the hob to the top of a not ventilated oven or a dishwasher.
• To guarantee under the bottom of the hob casing a space of 20mm to ensure a good air circulation of the electronic device.
• If a drawer is placed under the work, avoid to put into this drawer flammable objects (for example: sprays) or not heat-resistant objects.
• Materials which are often used to make worktops expand on contact with water. To protect the cut out edge, apply a coat of varnish or special sealant. Particular care must be given to applying the adhesive joint supplied with the hob to prevent any leakage into the supporting furniture. This gasket guaranties a correct seal when used in conjunction with smooth work top surfaces.
• The safety gap between the hob and the cooker hood placed above must respect the indications of the hood manufacturer. In case of absence of instructions respect a distance minimum of 650~mm .
• The connection cord should not be subjected, after building-in, to any mechanical constraint (for instance constraint given by a drawer installed below).
• WARNING: Use only hob guards designed by the manufacturer of the cooking appliance or indicated by the manufacturer of the appliance in the instructions for use as suitable or hob guards incorporated in the appliance. The use of inappropriate guards can cause accidents.

ELECTRICAL CONNECTION

• The installation of this appliance and the connection to the electrical network should be entrusted only to an electrician perfectly to the fact of the normative regulations and which respects them scrupulously.
• Protection against the parts under tension must be ensured after the building-in.
• The data of connection necessary are on the stickers place on the hob casing near the connection box.
• The connection to the main must be made using an earthed plug or via an omnipolar circuit breaking device with a contact opening of at least 3mm .
• The electrical circuit must be separated from the network by adapted devices, for example: circuit breakers, fuses or contactors.
• If the appliance is not fitted with an accessible plug, disconnecting means must be incorporated in the fixed installation, in accordance with the installation regulations.
• The inlet hose must be positioned so that it does not touch any of the hot parts of the hob or oven.

Caution!

This appliance has only to be connected to a network 230V 50 / 60Hz

Connect always the earth wire.

Respect the connection diagram.

The connection box is located underneath at the back of the hob casing. To open the cover use a medium screwdriver. Place it in the slits and open the cover.

Mains Connection Cable diameter Cable Protection calibre
230V~ 50/60Hz 1	Phase + N 3 x	2.5 mm²	H 05 VV - F H 05 RR - F	25 A *
400V~ 50/60Hz 2	Phases + N	4 x 1.5 mm²	H 05 VV - F H 05 RR - F	16 A *

• calculated with the simultaneous factor following the standard EN 60 335-2-6

Connection of the hob

Setting up the configurations:

For the various kinds of connection, use the brass bridges which are in the box next the terminal

Monophase 230V\~1P+N

Put a bridge between terminal 1 and 2.

Attach the earth to the terminate "earth", the neutral N to terminal 4, the Phase L to one of the terminals 1 or 2.

Biphas400V\~2P+N

Attach the earth to the terminate "earth", the neutral N to terminal 4, the Phase L1 to the terminals 1 and the Phase L2 to the terminal 2.

Caution! Be careful that the cables are correctly engaged and tightened.

We cannot be held responsible for any incident resulting from incorrect connection or which could arise from the use of an appliance which has not been earthed or has been equipped with a faulty earth connection.

Chere cliente, cher client,