Pro Trim 600TR - Lawn mower Texas - Free user manual and instructions

Product type	Self-propelled lawn mower
Brand	Texas
Model	Pro Trim 600TR
Engine	TG595, 173 cm³, 2.9 kW at 3000 rpm
Cutting width	60 cm
Cutting height	45 to 120 mm (adjustable)
Cutting wire diameter	4 mm
Transmission	Self-propelled (auto-traction)
Wheel diameter	14 inches
Adjustable steering	Yes
Net weight	46 kg
Sound pressure level (LpA)	84.2 dB(A)
Sound power level (LwA)	104 dB(A)
Vibrations (hand/arm)	6.7 m/s² / 5.0 m/s²
Recommended fuel type	Unleaded E5
Engine oil type	SAE-30
Safety	Emergency stop, protection against projections, safety distance 15 m
Maintenance	Clean after use, oil change after 5 h then once a year
Spare parts	Available at www.texas.dk and from retailers

Frequently Asked Questions - Pro Trim 600TR Texas

How to start the Pro Trim 600TR lawn mower?

Before starting, check the oil level (SAE-30) and fill with unleaded E5 gasoline. Prime the pump 3 to 6 times, set the engine switch to 'I', then pull the starter cord while guiding it back during recoil. Then engage the blade activation lever and the self-propulsion lever.

What oil to use and how to change it?

Use SAE-30 oil. The oil change must be done after the first 5 hours of use, then once a year. Extract the used oil through the fill hole using a syringe and a hose, then refill with new oil. Dispose of used oil safely.

How to adjust the cutting height?

Loosen the two 4 mm Allen screws (see figure 10), adjust the cutting head up or down to get a height between 45 and 120 mm, then retighten the screws.

What are the important safety instructions?

Wear tight clothing, non-slip boots with steel toe caps, gloves and hearing protection. Never leave children or animals nearby. Keep a safety distance of 15 meters. Never refuel indoors or with a hot engine. Turn off the engine before any maintenance.

What to do if the engine does not start?

Check the fuel system (is there gasoline?), the spark plug, and make sure the tank contains gasoline. Consult the engine manual for more precise diagnostics.

How to maintain and clean the machine?

After each use, clean the machine with a garden hose to remove dirt and grass. Do not use a pressure washer. Clean the serial number with a damp cloth. Store it in a clean and dry place. Wipe surfaces with a slightly oiled cloth to prevent rust.

What is the safety zone during use?

When the engine is running, you must stay within the operating zone indicated in figure 9. If you need to leave this zone (e.g., to attach an accessory), first stop the engine.

Can I use the mower on slopes?

Yes, the machine can work on slopes up to 15% gradient. Beyond that, the engine risks insufficient lubrication. Be extremely careful and do not run.

Where to find spare parts?

Spare parts designed specifically for your product are available on the website www.texas.dk. You can also contact your retailer. Have the part number ready to facilitate ordering.

What clothing to wear when using the mower?

Wear tight work clothing, work gloves, hearing protection and non-slip boots with steel toe caps. Avoid loose clothing that could get caught in rotating parts.

USER MANUAL Pro Trim 600TR Texas

Identification of dele 10

Beklaedning 10

Sikkerhedszone 10

Identification of dele

Se Fig. 1:

A. Startsnor
B. Greb for aktivering af trimmerhoved
C. Greb for Selvtraek
D. Motor
E. Hjul
F. Trimmer snore
G. Trimmerhoved
H. Gummiafdaekning
I. Skaerm
J. Motorskjold

GB - Table of Contents - "Original instructions"

Warning symbols. 2
Illustrations 5
Safety precautions. 12
Identities of parts 13
Assembly 13
Clothing 13
Safety zone 13
Starting and stopping the engine 13
Operating the machine 13
Adjustment of the cutting height 14
Cleaning 14
Changing the oil 14
Storage 14
Troubleshooting. 14
Noise, vibration and precautionary measures 14
Specification 14
EC Certificate of conformity. 24

Congratulations on purchasing your new machine. Please read this instruction manual carefully, especially the safety warnings marked with the symbol:

Spare parts

Spare part drawings for the specific product can be found on our website www texas.dk If you find the part numbers yourself, this will facilitate more rapid service.

For purchase of spare parts, please contact your dealer. You will find a list of dealers on the Texas website.

Safety precautions

Setup

Do not put hands or feet near or under rotating parts.
4 Read this manual carefully. Make sure that you are familiar with the different controls, settings and handles of the equipment.
4 Know how to stop the unit and ensure that you are familiar with emergency stop.
Never allow children or people unfamiliar with these instructions to use the machine. Note, that local regulations can restrict the age of the operator.
If you feel unwell, tired or have consumed alcohol or drugs, do not operate the machine.
Always inspect the machine before usage Ensure that no parts are worn or damaged.
Replace worn out or damaged elements and bolts in sets to preserve balance.
The operator of the machine is responsible for people's safety.
Never use the machine near children or animals.
The operator of the machine is held liable for any accidents or hazards to other people and their property.
4 Thoroughly inspect the area, where the equipment is to be used, if necessary remove any foreign objects.
4 Do not refuel gasoline indoors or while the engine is running.
Spilled gasoline is extremely flammable; never refuel while the engine is still hot.
Wipe off any spilled gasoline before starting the engine. It may cause a fire or explosion!
Beware of hazards, while working on difficult soil hence vegetation
4 Boots with non-slip soles with steel jacket is required. Avoid loose-fitting clothes.

Operation

Always start the engine from safety zone.
Do not leave the safety zone while operating the machine, if it is necessary to leave the safety zone, turn off the engine before leaving the zone.
After striking a foreign object, stop the engine immediately, remove the spark plug cap and inspect the machine thoroughly for damage. Repair the damage before continuing
If the machine should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of damage.
Always disengage the levers, turn off the engine, and remove the spark plug, when the unit is left unattended.
Always turn off the engine and ensure that all moving parts have come to a complete stop before making any repairs, adjustments, or inspections.
Exercise extreme caution when operating on slopes.
Never operate the machine at a fast pace.
Do not overload machine capacity
Do not carry passengers.
Pay attention, while the machine is in reverse.
! Never allow any bystanders in front of unit.
Always disengage the machine, if not in use.
Only operate the machine at daylight or in fully illuminated areas
Ensure a stable foothold and always keep a firm hold on the handles. Always walk, never run.
Do not operate the equipment when barefoot or wearing sandals.
Exercise extreme caution when changing direction on slopes
1 Never attempt to make any adjustments, while the engine is running.
Use extreme caution when reversing or pulling the machine backwards
Never operate the engine indoor or in areas with low ventilation. The exhaustion from the engine contains carbon monoxide. Failure to observe could result in permanent injury or death.

Gasoline safety

Use extreme care in handling gasoline. Gasoline is extremely flammable, and the fumes are explosive.
Serious personal injury can occur, when gasoline is spilled on yourself or your clothes. Rinse your skin and change clothes immediately!
Use only an approved gasoline container. Do not use soft drink bottle or similar!
Extinguish all cigarettes, cigars, pipes and other sources of ignition.
1 Never refuel your machine indoors.
Let the engine cool down before refilling
Never fill the fuel tank to more than 2.5cm below bottom of filler in order to provide space for fuel to expansion.
After refueling, ensure that the cap tighten securely.
Never use the lock-function on the gasoline gun, when refueling.
Do not smoke while refueling.
1 Never refuel inside a building or where gasoline fumes may get in contact with an ignition source.
Keep gasoline and engine away from appliance, pilot lights, barbecues, electric appliances, power tools, etc.
If the fuel tank has to be drained, this shall be done outdoors

Maintenance and storage

4 The engine shall be stopped when carrying out maintenance and cleaning operations, when changing tools and when being transported by means other than under its own power.
4 Check regularly that all bolts and nuts are tightened. Retighten if necessary.
The engine must be completely cooled before storing indoors or covered.
If the machine unused for a period of time, please refer to the instructions in this manual.
4 Maintain or replace safety and instruction labels, as necessary.
Only use original spare parts or accessories. If not original parts or accessories is used, the liability is no longer applied.
Replace faulty silencers.

Miscellaneous

The gears are delivered pre-greased. However, always ensure they are well greased before each use.
The motor is not pre-filled with oil.
Factory-fitted control devices, such as the handle-mounted clutch cable, must not be removed or exposed.
Only drain the fuel tank outdoors. Gasoline is extremely flammable and the fumes are explosive.
Ensure that the machine is properly secured when transported on a flatbed etc.
Reduce the throttle during engine shutdown and close the fuel valve.

Identities of parts

Identification of parts, see Fig. 1

A. Start cord
B. Trimmer activation handle
C. Self-propelled handle
D. Engine
E.Wheel
F. Trimmer line
G. Trimmer head
H. Rubber cover
I. Protection guard
J. Engine protection cover

For explanation of engine, see separate engine manual.

Assembly

Please follow the steps in figures 2-5:

1. Mount lower handlebar with 4 bolts on the console. After that mount the upper handlebar. The spacers need to be on the inside. As shown on Fig. 2A
2. Attach the clutch handles on the handlebar, as shown on Fig. 2B. Cable which comes out from right side of chassis, should be attached to right side of handlebar. Equivalent for left side.
3. Mount the wheels with the bolts shown on Fig. 3B. The spacers need to be between the wheel and the bolt.
4. Mount the engine protection cover with the 13mm bolts shown on fig. 3A.
5. Fit the protection guard on the machines as shown on Fig. 4.
6. Mount trimmer line. Follow the procedure step 1-2-3 as shown on Fig. 5.

The trimmer line must have length of max 52 cm and must always be attached in sets. There must be attached trimmer lines on both sides of the trimmer head.

Mounting the start cord in holder: Fig. 7A

1. Pull gently the starter cord from the engine.
2. Attach the starter grip on the rack of handlebar.

Fill the motor with engine oil.

See changing the oil section for more details.

Clothing

When using the machine, wear close-fitting work clothes, hard-wearing work gloves, ear defenders and non-slip boots with steel toecaps.

Safety zone

While the machine is being operated and the motor is running, do not leave the operation zone marked with arrows on Fig. 9. If it is necessary to leave the operation zone, for example to attach an accessory, first stop the engine.

Starting and stopping the engine

Always check the oil level prior to use!

On engines with dipstick the oil level must always be between the min. and max. On engines without dipstick the oil must be visible to the edge on filler hole, when the engine is horizontal position. Always use SAE-30 oil. Use only unleaded E5 gasoline. Never over-fill the gas tank.

Start

1. Pump the primer bulb 3-6 times. See Fig. 7B
2. Set the switch on engine to "l". See Fig. 6.
3. Pull the start cord to start the engine. See Fig. 7A. Always feed the start cord back into the engine by hand.
4. Activate the trimmer activation handle. Fig. 8A.
5. Activate the self-propelled handle. Fig. 8B.

Stop

1. Release both clutch handles.
2. Set the switch on engine to "O". See Fig. 6.

Vibrations may travel up into the handle during use. We therefore recommend taking a break, every 2 hours.

Operating the machine

1 Remove all foreign objects from the work area before using the machine. Stones, glass, branches and similar items may damage the machine. Also check the bolts are tightened.
Start the motor as per the instructions above. Stand clear of the machine's moving parts.
1 Never attempt to move the machine in any way other than intended for normal use while the motor is running.

KEEP A SAFETY DISTANCE OF 15 METERS.

The machine can work in almost any kind of vegetation. The trimmer head turns clockwise which means that the machine throws the harvested out on the right side.

The machine has a low center of mass and large wheels. This makes it suitable for working on slopes with a gradient of up to 15% . Warning: Avoid driving on slopes steeper than 15% , as the engine in such case will lack lubrication which can result in a damaged engine.

The machine workload should match the trimmer capacity. This is ensured by always keeping the same steady RPM on the trimmer head. Avoid downspin in RPM. A downspin in the RPM on trimmer head can be a sign on overload.

Adjustment of the cutting height

Follow the adjustment procedure as shown in Fig. 10 It is possible to adjust the cutting height on the trimmer head in several positions between 45 - 120mm

To adjust the trimmer height, you have to loosen the two 4 mm allen screws. Then you can adjust the trimmer head up and down. Tighten both screws again once the wanted cutting height is chosen.

Cleaning

The machine should be cleaned after use. Use a garden hose to wash off soil and dirt. Remove the trimmer head from the trimmer axel to remove wedged grass etc. from the rotor shaft. The chassis number should only be cleaned with a damp cloth to avoid unnecessary wear. Avoid using a high-pressure washer during cleaning.

Changing the oil

The oil should initially be changed after the first 5 hours of use, and thereafter once per year. Use an oil extractor kit.

1. Suck the oil up through the oil filler hole using the syringe. Use the hose to reach the sump.
2. Transfer the used oil to the container.
3. Fill the engine with new SAE-30 oil.
4. Check the oil level using the dipstick.

Remember to dispose of used oil in a safe way.

Oil and oil extractor kit are not included

Storage

• If the machine is likely to be stored unused for prolonged periods, follow the instructions below. This will ensure longer machine lifetime.
• Use a garden hose to wash off soil, grass and dirt. Remove any grass, etc. from the shaft. The chassis number should only be cleaned with a damp cloth to avoid unnecessary wear. Avoid using a high-pressure washer during cleaning.
• Wipe the machine with a damp cloth so that all surfaces are clean. Wipe the surfaces down with an oily cloth to prevent rust.
  Always store the machine in a dry, clean location.

Troubleshooting

The motor will not start

1. Check the spark plug.
2. Check there is fresh gas in the tank.
3. See separate motor instructions for further troubleshooting.

The motor is not running smoothly

1. Check there is fresh gas in the tank.

The trimmer will not rotate

1. Check the cables are in good working order and fitted correctly.
2. Check and remove wedged grass.
3. Check that the belt is fitted correctly.

Noise, vibration and precautionary measures

1. Long-term exposure to noise levels exceeding 85 dB (A) are damaging. Always use ear defenders when the machine is being used.
2. To reduce noise levels further, only use the machine in an open environment.
3. Vibrations can be reduced further by holding the handle firmly.
4. To avoid disturbing others, the machine should only be used during the daytime.
5. Always wear close-fitting work clothes, hard-wearing work gloves, ear defenders and non-slip boots with steel toecaps.
6. Take a 30-minute break every 2 working hours.

Specification

Engine TG595 17cc (Rato RV170)
Effect 2,9 KW/3000 RPM.
Working width Max 60 cm
Working Hight 45-120 mm
Trimmer line 4 mm
Transmission	Push
Wheels 14"
LpA 84.2 dB(A)
LwA 104 dB(A)
Vibrations (L / R)	6,7 m/s2/5,0 m/s2
Weight	46 kgs

2006/42/EC - 2014/30/EU - 2000/14/EC amended by 2005/88/EC

Materiellet er udført i overensstemmelse med folgende standarder · Conforms with the following standards - In Übereinstimmung mit den folgende Standards · Conformément aux normes suivantes · Conforme ai seguenti standards

EN 14910+A1:2014

EN ISO 14982: 2009

LA:104dB(A)L pA:84.2dB(A)

Ah - L : 6.7 - Ah - R5.0m / s^2

S/N: 2203024410000 - 2403024499999

Texas Andreas Petersen A/S Knullen 22 · DK-5260 Odense S

05.04.2022

Johnny Lolk Managing Director

Responsible for documentation Johnny Lolk