RCR3025EBT - Hi-fi system ROADSTAR - Free user manual and instructions

Product Type	Portable Hi-Fi System
Brand	Roadstar
Model	RCR3025EBT
Power Supply	AC 230V~50Hz or DC 6V (4 LR20 batteries)
Main Functions	AM/FM/SW radio, cassette player, Bluetooth, USB/SD, direct encoder, built-in microphone
Radio Bands	AM: 520-1620 kHz, FM: 87.5-108 MHz, SW: 3-23 MHz
Speaker Power	2 x 1.5 Wrms
Bluetooth Connectivity	Yes, max range 10 m, radiated power < 4 dBm
USB/SD Ports	USB 3.0 max. 32 GB, SD max. 32 GB
Headphone Output	3.5 mm jack socket
Recording Function	Recording to cassette from radio, Bluetooth, USB/SD or built-in mic; direct encoding to USB/SD
Auto Power Off	Yes, after 10 minutes without sound
Care and Cleaning	Clean with a soft, dry cloth; avoid liquids and moisture
Safety	Do not open the casing; unplug during prolonged non-use; avoid exposure to water, heat, and direct sunlight
General Information	Manual available in multiple languages; EU declaration of conformity online

Frequently Asked Questions - RCR3025EBT ROADSTAR

How to turn the unit on and off?

Move the function selector (10) to the desired source to turn on. To turn off, set it to OFF.

How to listen to the radio?

Set the function selector (10) to RADIO, choose the band with the band selector (11), and adjust the frequency with the tuning control (12). For better reception, reorient the antenna (3).

How to use Bluetooth?

Set the function selector (10) to BT, press MODE (17) several times to select Bluetooth mode (blue LED). Connect your portable device to the Bluetooth ID 'RCR-3025EBT'. Music control is done from your device.

How to play a cassette?

Set the function selector (10) to TAPE, press STOP/EJECT (5) to open the door (22), insert the cassette, close it, then press PLAY (8). Use PAUSE (4), F.FWD (6), and RWD (7) to control playback.

How to record onto cassette?

Insert a blank cassette into the door (22), choose the source (radio, Bluetooth, USB/SD, or mic), start playback of the source, then press RECORD (9) and PLAY (8) simultaneously. Press RECORD (9) to stop.

How to use a USB or SD device?

Set the function selector (10) to USB, plug your USB key or SD card into the corresponding socket (26/27). Playback starts automatically. To avoid damaging the device, remove it only when the unit is off.

How to encode directly to USB/SD?

Set the desired source (radio, cassette, or mic), connect a USB/SD device, press ENCODING (16) twice to start encoding. Press ENCODING (16) again to stop.

What to do if the unit does not respond?

This may be due to electrostatic discharge. Turn off, unplug the power cord, and remove all batteries. Wait a few seconds, then power on again.

What type of batteries to use for battery operation?

Use 4 LR20 (D size) batteries. Insert them into the compartment (24) observing polarity. Remove batteries if the unit is not used for a long time to avoid leakage.

How to clean and maintain the unit?

Clean the exterior with a soft dry cloth. Do not use liquids or aerosols. Avoid moisture, excessive heat, and direct sunlight. Do not open the casing.

USER MANUAL RCR3025EBT ROADSTAR

• INSTRUCTIONS - All the safety and operating instructions should be read before the radio is operated. The manual should be retained for future reference.
• HEED WARNINGS - All warnings on the appliance and in the operating instructions should be adhered to.
• WATER AND MOISTURE - The appliance should not be used near liquids or in rooms with a high level of humidity.
• VENTILATION - The appliance should be situated so that its location or position does not interfere with its proper ventilation.
• HEAT - The appliance should be situated away from heat sources such as radiators, stoves or other appliances that produce heat.
• POWER SOURCE - The radio should be connected to power supply only of the type described in the operating instructions or as marked on the appliance.

• POWER CORD PROTECTION - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon/against them.

• OBJECT AND LIQUID ENTRY - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

• DAMAGE REQUIRING SERVICE

The appliance should be serviced by qualified service personnel when:

• The power supply cord or plug has been damaged;
• Objects have fallen into or liquids has been spilled into the radio;
• The appliance has been exposed to rain;
• The appliance has been dropped or the enclosure damaged;

• The appliance does not appear to operate normally.

• SERVICING - The user should not attempt to service the appliance beyond that descrive in the user operating instructions. All the servicing should be referred to qualified service personnel

Note: If the display does not function properly or no reaction to operation of any control may due to the electrostatic discharge. Switch off and disconnect the AC cord and remove all the batteries, then turn the power back on after a few seconds.

POWER SOURCES

AC POWER: You can power your portable stereo system by plugging the AC power cord into the AC plug (25) at the back of the unit and into a wall AC power outlet.

Check that the rated voltage of your appliance matches your local voltage.

Make sure that the AC power cord is fully inserted into the appliance.

BATTERY POWER: To use the radio with batteries, disconnect the AC power cord and insert 4 × "LR20" batteries into the compartment (24).

Be sure that the batteries are inserted correctly to avoid damage to the appliance.

Remove the batteries when the radio will not be used for a long period of time, as this will cause leakage to the batteries and subsequently damage to your radio.

TO USE THE RADIO

1. Move the [FUNCTION SELECTOR] (10) to the desired;
2. (Please see detailed instructions for each Source in the following chapters);
3. Adjust the volume with the [VOLUME KNOB] (1) to the desired level;
4. Move the [FUNCTION SELECTOR] (10) to OFF to turn OFF the unit.

Note: When no sound is produced, the unit will switch OFF automat. after 10 minutes

RADIO OPERATION

1. Set the [FUNCTION SELECTOR] (10) to "RADIO" mode;
2. Select desired band by using the [BAND SELECTOR] (11);
3. Adjust the frequency to your desired station by using the [TUNING KNOB] (12).

Note: For a better reception, reorient the antenna (3).

TAPE OPERATION

1. Set the [FUNCTION SELECTOR] (10) to "TAPE" mode;
2. Press STOP/EJECT to open the [CASSETTE DOOR] (22) and insert your tape;
3. Close the [CASSETTE DOOR] (22);

3 English

1. Press [PLAY] (8) to start playing tape.
2. Press [PAUSE] (4) when you want to stop playing tape operation temporarily, press again to resume tape operation.
3. Press [STOP/EJECT] (5) when finished, press again to open the door.
4. Press [F.FWD] (6) or [RWD] (7) to start rapid tape winding either forward or reverse direction.

CASSETTE RECORDING

The unit can record from Radio, Bluetooth, USB/SD or Built-In microphone.

1. Insert the cassette into the [CASSETTE SLOT] (22);
2. Perform normal playback of the source you want to record;
3. Press the [RECORD] (9) and [PLAY] (8) buttons together to start recording;
4. Once the record is finished, press the [RECORD] button (9) to stop recording.

USB/SD OPERATION

1. Set the [FUNCTION SELECTOR] (10) to "USB" mode;
2. Plug an USB / SD stick into the [USB/SD PORT] (26/27);
3. Playback will start automatically from the first track.

Note: Some mp3 player may not be able to play via the usb socket. this is not a malfunction of the system.

Note: To avoid damage to USB/SD memory, remove it only when the radio is OFF.

DIRECT USB/SD ENCODING

The unit can encode from Radio, Tape or Built-In microphone.

1. Plug the USB or SD stick into the [USB/SD PORT] (26/27);
2. Perform normal playback of the source you want to encode & record;
3. Press the [ENCODING] button (16) to start encoding;
4. Once the record is finished, press the [ENCODING] button (16) to stop recording.

BLUETOOTH OPERATION

1. Set the [FUNCTION SELECTOR] (10) to "BT" mode;
2. Press the [MODE] (17) repeatedly to select Bluetooth mode (BLUE LED);
3. Connect your Bluetooth portable device to the ID Bluetooth tagged as "RCR-3025EBT";
4. You can now transfer the music to the RCR-3025EBT.

Note: Music control (play, pause, etc) must be done from your external device.

TECNICAL SPECIFICATIONS

Power Supply: AC 230V ~ 50Hz.

DC 6V = (4 x "LR20" Batteries).

Radio Frequency Coverage

AM: 520 - 1620 kHz

FM: 87.5 - 108 MHz.

SW: 3 - 23 MHz.

Speaker

Output Power: 2 × 1.5 Wrms.

General

Headphones Out: 3.5mm jack plug.

BT Maximum radiated Power: < 4 dBm (2.5 mW).

USB Port Version: USB 3.0, max 32GB.

SD Port Version: max. 32GB.

Specifications and design are subject to possible modifications without notice due to improvement.

WARNING

The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product.

The lightening flash with arrowhead symbol within the triangle is a warning sign alerting the user of "dangerous voltage" inside the unit.

To reduce the risk of electric shock, do not remove the cover. No user serviceable parts inside the unit. Refer all servicing to qualified personnel.

This unit operates on 230V 50Hz . If the unit is not used for a long period of time, remove the plug from the AC mains.

Ensure all connections are properly made before operating the unit.

This unit must not be exposed to moisture or rain.

This unit should be positioned so that it is properly ventilated. Avoid placing it, for example, close to curtains, on the carpet or in a built-in installation such as a bookcase.

Do not expose this unit to direct sunlight or heat radiating sources.

CORRECT DISPOSAL OF THIS PRODUCT (Waste Electrical & Electronic Equipment)

This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

ORT DER BEDIENELEMENTE

1. LAUTSTÄRKEREGLER
2. BASSREGLER
3. ANTENNE
4. KASSETTE - PAUSE
5. KASSETTE - STOP / EJECT
6. KASSETTE - FAST FORWARD
7. KASSETTE - REWIND
8. KASSETTE - PLAY
9. KASSETTE - RECORD
10. FUNKTIONSREGLER
11. BANDWAHLSCHALTER
12. ABSTIMMUNG
13. USB/SD - SKIP -
14. USB/SD - PLAY / PAUSE
15. USB/SD - SKIP +
16. USB/SD - ENCODING
17. USB/SD/BLUETOOTH - MODE
18. KOPFHÖRER AUSGANG
19. LED
20. EINGEBAUTE MIKROFON
21. LAUTSPRECHER
22. KASSETTENFACH
23. DIAL SCALE
24. BATTERIEFACH
25. NETZSTECKER
26. USB-BUCHSE
27. SD-BUCHSE

SICHERHEITSHINWEISE

BT Maximum radiated Power: < 4 dBm (2.5 mW).

DC 6V = (4 battery "LR20").

ELIMINACAO CORRECTA DESTE PRODUCTO

Hereby, Roadstar Management SA declares that the radio equipment type RCR-3025EBT is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address:

http://roadstar.com/images/ce/RCR-3025EBT.pdf

or by scanning the following QR Code.

http://roadstar.com/images/ce/RCR-3025EBT.pdf

http://roadstar.com/images/ce/RCR-3025EBT.pdf

http://roadstar.com/images/ce/RCR-3025EBT.pdf

http://roadstar.com/images/ce/RCR-3025EBT.pdf

http://roadstar.com/images/ce/RCR-3025EBT.pdf

http://roadstar.com/images/ce/RCR-3025EBT.pdf

http://roadstar.com/images/ce/RCR-3025EBT.pdf

http://roadstar.com/images/ce/RCR-3025EBT.pdf

Roadstar Management SA, via Passegiata 7 CH 6883 Novazzano (Switzerland)