iZi Turn M iSize - Car seat BESAFE - Free user manual and instructions

USER MANUAL iZi Turn M iSize BESAFE

BeSafe®
Scandinavian Safety

Thank you for choosing BeSafe IZI Turn I-Size

It is important that you read this user marva. BEFORE installing your seat, incorrect installation on could undergo your shix.

! Vital Information

• The child sea MUST NOT be installed in a front

passenger seat WITH AN ACTIVATED AIRDAG.

• This seat can only be installed in a car equipped with

SOLI+ anchorage points approved to

No. 14 or other equivalent standards.

• For the suitable process in the case, we see the specific functions

• These the car list to find out whether your car model is improved for

The latest update of the British Bank is a result on the ECA site www.bosafa.com. Euro car is my cement in the country.

Chinese text: EnF's for (a) my information

• i7. T. qu-i-Sie is enjoyed re-earing for children with a small

Sight from 81 to 105 cm, with a maximum height up to 18 km and

forward facing for children with a size, are height from 30 to 105 cm

with a maximum height at 18 kg.

• Important. Do not use forward feeding before the child is user

15 mm

- When driving with a child sitting in the seat, the seat must always be

to the light starting, driving distance of the vehicle. Never drive

The seat, rotated to the side when a chow is leaning in the seat. It is recommended out to arrive into the seat located to the side when

The 5075-6090

- BeSafe recommends to use the seat for as long as possible in "the

ca-1a1a2a1a10

• The harness scraps must always be locked when the child is in

the bean.

- The harness straps must be tightened without slack and not twisted.

• The shoulder pass contains magnets. Magnets can influence

electronic equipment such as pacemakers.

- Protect any part of the child's body which is exposed to the sun

• The first support must always be held. When said that "is their support, so there is down, it touches the floor of the vehicle."

Subject: 5.0% pushed down from it, it pushed 3.0% of the vehicle in front of the seat and that the seat is opened horizontal in line.

The first of the seal and that the seal is a peace-based, not a fair vehicle with the spirit, evil, the middle. The indicators at the floor

super should always show green

• The recommend that this seal is used only for children who are still

upright, usually not younger than 6 months.

When the side support with a child is over 2 years or later, when the child does not fit between these sides supports answers.

After search, the seat must be replaced. Although it was look

unamended it was, were to earn another accident. The rest may not

be able to protect your child to the level to which it was designed.

• Present the seat from becoming trapped or weighed down by

luggage, seats and/or slimming doors.

• Make sure to lighten the harness essentially well, so that you can no

longer made a lot in the bells. When you listen the harness, make

sure at the child's particular well against the lack of

- 32 NO attempt: 1500 m³, 400 g of 300 gm part of the seat.

We have up this upended to the next

• Make sure all passengers are informed about how to release your

child in case of emergency

• Make sure image of other objects are properly secured. Unsec-red

luggage may cause severe injuries to children and adults in case

of accidents.

- Never use the seat without the cover. The cover is a safety feature

and may only be replaced by an original double tower.

- Do not use any aggressive clearing products: these may harm the

Construktion Heter after the seat.

• Desire advice that child best should not be bought 5% etc.

表10-45号

• A...A has user status, her late-use with 1% best

- Do not use the seal of large draft years due to being a quality of the material may change.

10.2OT use a home, has no home

to be used in a vehicle.

• 'When the child sex is my

the child set might touch the interior. We recommend using a

|Be5a's protection cover in these places to avoid tuts marks

discolouration to the interior of the vehicle, especially in vehicles with

leather or wooden cibers.

- If in fact, in said section the last part of the first side

Preparing to install

• Adjustable headrest	(1a)
• Shoulder straps	(1b)
• Seat cushion	(1c)
• Harness buckle	(1d)
• Side support	(1e)
• Central adjuster	(1f)
• Reclining handle	(1g)
• Release handle headrest	(1h)
• Spirit level	(1i)
• Floor support	(1j)
• Floor support height indicator	(1k)
• Height adjuster floor support	(1l)
• Rotation release handle	(1m)
• Switch for ISOfix connectors (2x)	(1n)
• ISOfix connectors (2x)	(1o)
• ISOfix release switch	(1p)
• ISOfix indicators (2x)	(1q)
• ISOfix car anchorage (2x)	(1r)

Installation

1. When installing in the back seat of the vehicle, push the front seat of the vehicle forward as far as possible and adjust the back rest into an upright position (if it can be adjusted).
2. When installing in the front seat of the vehicle, adjust the back rest into an upright position.
3. Position the vehicle on a horizontal surface when installing the seat.
4. When the base is lifted the floor support should fall downwards from underneath the base. Do this outside the car.
5. Push down the switch for the ISOfix connectors at both sides to release the ISOfix connectors. (2)
6. Position the base on the vehicle seat. Click the ISOfix connectors on to the ISOfix anchorages on the vehicle seat. Make sure that both ISOfix indicators are green. (3)
7. Push the seat towards the backrest of the vehicle seat until it touches the backrest. (4)

8. The ISOfix connectors will have resistance sliding in, in the most outward positions, before they are connected with the ISOfix anchorage of the vehicle.

9. Tip: once the ISOfix connectors are installed, the seat can be turned towards the door of the vehicle to get a better view on the installation display.

10. Remove the yellow cap from the floor support. Adjust the floor support, so it is in contact with the floor of the vehicle. (5)
11. The height indicator of the floor support shows green when the floor support is in contact with the floor. (5)
12. Lift the base at the front side (near the spirit level) and extend the floor support till the spirit level is in the middle, indicating a horizontal position of the base. (5)
13. Tip: place one foot onto the bottom end of the floor support while lifting the base to make adjusting the length at this step easier.
14. The alarm sound stops when the floor support indicators show green and it is in contact with the floor. Make sure that the horizontal spirit level shows a horizontal position of the seat. (5)
15. When having the child seat installed rear facing in the back, it is recommended to position the front vehicle seat in a way that it is close to the touchpoint with the child seat. Make sure that the child seat can still rotate freely. When having the child seat installed rear facing on the passenger seat in the front, it is recommended to position the passenger seat in a way that the dashboard is close to the touchpoint with the child seat. Make sure that the child seat can still rotate freely.
16. Tip: If you feel like the base has too much side movement, you can install the seat tighter against the vehicle seat backrest. Make the support leg short, grab the base and push it against the vehicle backrest with more force. Move it side to side until you hear one more 'click' per side, then lift the base into horizontal position again
17. The seat is delivered with removable SIP+ (side impact protection +). This extra side impact protection should be used on the door side of the vehicle. It can be connected by slotting between the seat shell and the fabric. The seat already offers high level integrated side impact protection. This extra side impact protection improves the protection in the side impact still further. (Not on all models) (6)
18. Tip: For an optimal height of the SIP+, position it between the two raised dots on the side of the seat shell.
19. Do not use the SIP+ on the seat when the space between seat and door of the vehicle is too small, which might lead to a situation where the seat is not positioned correctly on the vehicle seat. (6)

Removal of the seat from the vehicle

1. To remove the seat from the vehicle, turn the seat rear facing and push the seat upwards while adjusting the floor support to its shortest length.
2. Release the ISOfix connectors out of the seat by pushing down the switch for the ISOfix connectors on both sides. Pull the ISOfix release switch on both sides to disconnect from the ISOfix car anchorage.

Positioning of the child

1. Turn the seat towards the door while you pull the rotation release handle upwards.
2. Check that the shoulder strap slots are level with your child's shoulders. (7)
3. While pressing the button of the central adjuster, pull the shoulder straps away from the seat with a flat hand. Make sure to pull the straps evenly so that they stay at the same length. (8)
4. Open the harness buckle. (9)
5. The height of the shoulder straps and the headrest can be adjusted by pulling the release handle upwards at the back of the headrest and pulling the headrest up or down. (10)
6. Position the shoulder straps over the marking at the sides of the seat to use the magnets to keep the harness open while you position the child. (11)
7. When the child is positioned, place the shoulder straps over the child's shoulders and close the buckle: CLICK! (12)
8. Pull the harness strap through the central adjuster in the direction of the arrow straight up/forwards. Continue pulling until the harness is a comfortable but a firm fit. (13)
9. Turn the seat against or with the driving direction before driving and check if the release handles show green and the seat is locked into the driving direction. (14)

Removing and refitting the cover

• Do take care when you remove the cover, as re-fitting the cover is done in reverse.
• The cover of the headrest can be taken off separately by disconnecting the beads at the back and pulling off the fabric towards the front.

! Warning: potential misuse

• The child seat MUST NOT be installed in a front passenger seat WITH AN ACTIVATED AIRBAG.
• The floor support must always be used. Make sure that the floor support is fully pushed down and that the seat is positioned horizontal with the spirit level in the middle.
• Never drive with a child in the seat if the seat is rotated to the side.
  • Make sure the indicators are green before you drive.

Guarantee

• Should this product prove faulty within 24 months of purchase due to materials or manufacturing fault, except covers and harness straps, please return it to the original place of purchase.
• The guarantee is only valid when you use your seat appropriately and with care. Please contact your retailer, they will decide if the seat will be returned to the manufacturer for repair. Replacement or return cannot be claimed. The guarantee is not extended through repair.
• The guarantee expires: when there is no receipt, when defects are caused by incorrect and improper use, when defects are caused by abuse, misuse or negligence.

Takk for at du valgte BeSafe iZi Turn i-Size

f facebook.com/BeSafe

@besafeinternational

BeSafe®

Scandinavian

Safety