secuENTRY easy 5601 - Electronic lock Burg Wächter - Free user manual and instructions

USER MANUAL secuENTRY easy 5601 Burg Wächter

1) Access to the menu for programming

When the “Func:M” symbol is displayed, the menu can be reached by pressing the “Func” key. In the menu, the keys “1” and “2” can be used as a scroll function to navigate through its structure.

2) Deleting an entry action

When the “Func:C” symbol is displayed, the last entry can be cancelled by pressing the “FUNC” key.

3) Entry to previous programming level / Back

When you are in the menu, the symbol “Func:<” is displayed. By pressing the “FUNC” key, you return into the menu structure on the next higher level. Battery indicator Battery full Battery empty The display indicates battery statuses of the cylinder unit and the keypad unit. The indication on the display concerns the batteries with the lowest status. In case a battery is empty, the display indicates as follows: Replace battery in keypad or replace battery in knob. When the battery has been replaced and then the opening code entered twice, the currently lowest battery status is displayed. When only a single battery set is replaced, the display can still indicate an “incomplete” status, despite the replacement. In case you do not replace the batteries in spite of the replacement indication, you will have to enter the valid opening code once more in order to open the door. At the same time, the inner knob LED ashes 5 x 5 times. You can still open the door in this way approx. 50 times. Then it can only be opened using the administrator code. Now the batteries must be replaced, otherwise the door cannot be opened any more. Fingerscan sensor To open or register the particular nger.24 | English secuENTRY easy Dear customer, Thank you very much for your decision for the secuENTRY electronic lock system manufactured by BURG-WÄCHTER. This system has been developed and manufactured using the latest technical potential and satises high security requirements. The electronic cylinder can be used easily without any drilling in any door prepared for prole cylinder up to a door thickness of 118 mm (59 / 59, measured at the central detent bolt), and is perfectly appropriate for new installation as well as for retrotting. Depending on the specic system, various opening media are available. With systems containing a keypad, user administration is additionally integrated. You can nd out more on the following pages. Remove the battery protection strip from the inner knob in order to energise the cylinder. Important: Please read the entire User Manual before you start programming. We hope you enjoy your new locking system. General information about secuENTRY easy secuENTRY is available in two equipment congurations:

• secuENTRY easy PINCODE

• secuENTRY easy FINGERPRINT In the set congurations secuENTRY easy PINCODE and secuENTRY easy FINGERPRINT, the keypad is already registered in the cylinder. Administrator code / QR code The QR Code is required for both the setup of opening options using the BURG-WÄCHTER KeyApp and for the subsequent attaching and registration of a keypad or a cylinder. In secuENTRY Pincode and secuENTRY Fingerprint, the administrator code is factory-set to 1- 2 - 3 - 4 - 5 - 6 (please never forget to change it). Attention! In case you lose your administrator code and / or your QR code, any reprogramming and any use of administrator functions becomes impossible. Please store it carefully! SN: 10 : 0F : 00 : 34 30 : 42 : 25 : 00 : 00 : 25

1 Keypad (SN; MAC; AES; Type) 2 Cylinder (SN; MAC; AES; ADM)secuENTRY easy English | 25 Hint: The QR code can also be stored in an electronic form as a scanned le or a photograph on a protected data carrier. Additional functions available using the optional secuENTRY easy Software, for example:

• Assignment of authorisations

• 2 x MIGNON LR6 AA ALKALINE for the cylinder Optical signalling Optical signalling in the form of a LED is incorporated in the knob on the inner side of the door. This LED informs you on the following:

• 1 x brief: cylinder coupled

• 2 x brief: cylinder uncoupled

• 1 x brief, 1 x long, 2 sec pause, repeating: lock in programming mode

• 5 x briey, 2 sec pause, repeating at 20 sec: battery in cylinder empty Technical data Blocking times After 3 × wrong code is entered 1 minute, then always 3 minutes Display Adjustable to 12 languages Permissible ambient conditions * -15 °C / +50 °C / up to 93 % rel. air humidity (noncondensing) Allowed temperature range: -20 °C / +50 °C As a result of extreme temperature changes, the display can react slowly or darken. Keypad protection class Protection class keypad PINCODE IP65 Protection class keypad Fingerprint IP55 Transmitting power and frequency range: Bluetooth Low Energy Maximum Transmit Output Power 7,5dBm Frequency usage range 2,402GHz … 2,483 GHz

• In case the temperature exceeds the specied range, a corresponding warning message is indicated on the display. Provide for appropriate corrective action!26 | English secuENTRY easy Opening secuENTRY can be operated, depending on the equipment conguration, using a 6 digit numerical code, the Burg-Wächter KeyApp or with ngerprints. Opening with PIN code

• Enter the 6 digit PIN code (factory-set to 1- 2 - 3 - 4 - 5 - 6). The display indicates “Please use rotating knob!” and the LED integrated in the cylinder ashes once when the opening is successful.

• Turn the cylinder knob Opening with Fingerprint

• Move the registered nger from the top to the bottom centrally over the sensor. The display indicates “Please use rotating knob!” and the LED integrated in the cylinder ashes once when opening is successful.

• Turn the cylinder knob Opening with BURG-WÄCHTER KeyApp

• Hold your smart device in front of the cylinder knob and press the opening key of the KeyApp.

• The LED integrated in the cylinder ashes once when opening is successful.

from IOS 8.1.3. Please check under: www.burg.biz/secuentry/description whether other Smartphones are compatible with the app.secuENTRY easy English | 27

secuENTRY easy PINCODE Generally The electronic cylinder is operated by entering a PIN code. Additionally, the lock can also be operated using the BURG-WÄCHTER KeyApp. Contents of delivery

Shield foil Functions

• Total number of users: up to 5028 | English secuENTRY easy secuENTRY easy FINGERPRINT Generally The electronic cylinder is operated using a scanned nger. Up to 24 ngers can be programmed using the keypad. The users are created separately (USER XXX_FP). If a code and / or an transponder should be additionally assigned to a user, it is to be created separately. Additionally, the lock can also be operated using a PIN code, or the BURG-WÄCHTER KeyApp. Contents of delivery

Shield foil Attention! The ngerprint sensor must not be cleaned with detergents. Please use a slightly moistened cloth for this purpose. Functions

• Total number of users: up to 50, out of whom number of ngerprints: up to 24

• Conrm your selection using

• Now you can use the keys 1 or 2 to scroll until the administrator / user, whose user code should be changed, is displayed

• Enter the new code and conrm it with

• Repeat your entry and conrm it again with . “Code change accomplished” is displayed after a correct entry30 | English secuENTRY easy Sprache / Language menu Language setup

• Use the keys 1 or 2 to scroll until the required language is displayed

• Conrm with Administrator menu Various submenus are available under the Administrator menu Submenu create User with Code

• Conrm with . The “Create User” menu item appears

• Scroll using the 2 key till reaching “Create User: Code“

• Enter the administrator code in order to acquire the authorisation for programming

• The next free memory space is indicated (e. g. USER.003)

• Enter the 6 digit code and conrm it 2 × with

• “Data has been saved” is displayed Submenu create User with Fingerprint (This function is only active with secuENTRY easy Fingerprint)

• Conrm with . The “Create User” menu item appears

• Enter the administrator code in order to acquire the authorisation for programming

• “Register nger” is displayed

• Move the nger to be registered several times centrally over the sensor (the number of moves is indicated on the display)

• “User_XXX_FP successfully registered” is displayedsecuENTRY easy English | 31 Submenu Delete Using this menu, you can delete a user.

• Enter the administrator code in order to acquire the authorisation for programming

• Scroll till reaching the user or the identication medium (transponder) you wish to delete and conrm your selection 2 × with

• “Data has been deleted” is displayed Time Functions submenu (Premium only) This is intended for setting the time and date Setting the time: Not available as a standard function. Setting the date: Not available as a standard function. Setup submenu General system settings Register After a replacement of the cylinder or the keypad, the two units have to be newly aligned, so that they can resume communication. Registration of a keypad

• Now scroll using the 1 or 2 keys until reaching the Admin. Setup menu

• Enter the admin code of the unit to be registered

• “Data has been saved” is displayed after a successful registration Attention! Make sure that no other powered secuENTRY unit is placed within a direct reach of the device when registering a new keypad or a new cylinder, as such unit could be mistakenly addressed instead of the intended one. When in doubt, disconnect such units from power before the registration (remove batteries).32 | English secuENTRY easy Reorganise The use of this function is recommended when several users have been deleted.

• The “Reorganise” menu item appears

• Enter the administrator code in order to acquire the authorisation for programming

• “Reorganisation in progress” is displayed Submenu FP Reset (This function is only active with secuENTRY easy Fingerprint and with the secuENTRY KP FP keypad) All the stored ngerprints are deleted, however, the corresponding users are retained. Please select this menu and follow the instructions on the display in case of repeated error functions related to the use of ngerprints. Info menu The version and serial number of the system are displayed using this function. For security reasons, the complete serial number is indicated only in the administrator mode.

• Conrm with . The serial numbers of the keypad¨(EA) and of the cylinder (AA) are displayed. Remark: For security reasons, the serial number (AA) of the cylinder is not completely displayed before the entry of a valid administrator code.secuENTRY easy English | 33 Installation Instructions for secuENTRY easy cylinder Please read these Installation Instructions carefully before the assembly and then store them at a safe place. The cylinder has a special detent system, offering you a possibility of using the cylinder for doors with a thickness up to 118 mm (59 / 59 mm, measured at the central detent bolt). No prior adjustment is necessary. Attention: Be careful to not bang the knob anywhere, as the knob can break in such case. The lock should not be greased or oiled An incorporated locking screw in each knob is to x the rotary knobs. Attention: Never pull the inner knob completely from the shaft, as this might cause damage to the electronics! The locking screw, which ensures the detent on the shaft, may be loosened only lightly and it always remains in the plastic knob, providing protection against pulling it out. Outer side Inner side Outer knob Inner knob Cover Adapter 2 Adapter 1 Detent bolt Locking screw for xation onto the shaft Remark The base size of the cylinder is 30 mm per side. When delivered, the cylinder is completely collapsed (the smallest door thickness). Before you insert the cylinder into the door, you should adjust it to your door thickness. When installing the cylinder, proceed as follows: 1 Take a rough measurement of the door thickness (incl. ttings) 2 Pull the outer knob from the shaft, move the inner knob over the detent system (spacing 2.85 mm) to the required dimension. Schematic illustration of the mounted cylinder including the two adapters34 | English secuENTRY easy inner knob 30 mm ajustment range Schematic illustration of setup of the inner knob ajustement 3 Depending on the door thickness, you can afx an appropriate adapter on the outer side, in order to improve the path for the emergency key. The following combinations are possible: Space detent bolt / tting (mm) on the outer side Adapter 1 Adapter 2 < 43 – – 44 – 53 X – 54 – 60 X X Tab. 1: Space detent bolt / mounting [mm] on the outer side and the required adapter. 2,9 × 16 Adapter 2 M2 × 10 Adapter 1 4 Move the secuENTRY easy cylinder from inside to outside through the mortise lock into the door and then tighten the detent bolt. 5 Shift the inner knob over the shaft until attaining the required dimension. Please make sure that the clearance between the rotary knob and the door mounting is at least 1 mm. Then x the rotary knob using the hex key.secuENTRY easy English | 35 6 Before you x the outer knob, please consider whether you wish to use the attached cover panel for the prole cylinder section. If so, remove the protective sheet and x the cover panel onto the lock section. 7 Shift the outer knob into the required position on the shaft and x it with a clearance of at least 1 mm from the mounting using the hex! 8 The function test must be made with the door open.36 | English secuENTRY easy secuENTRY easy keypad installation The keypad is only included in secuENTRY easy Pincode and secuENTRY easy Fingerprint sets. Attention! Please remember that the keypad should not be attached to the door itself, otherwise it would transmit shocks when the door is being shut. The membrane afxed to the keypad rear side should not be sealed with glue and / or any other substance under any circumstances! Exchange of air must also be possible after the installation!

• Determine the installation place for the keypad. For that purpose, enter the opening code (e. g. PIN code, ngerprint, …) at the desired mounting place and check whether the lock opens.

• Place the keypad correspondingly. You can then decide whether you want to glue the wall holder directly on the wall or whether you prefer having it screwed on. The slotted holes in the wall holder provide for an exact alignment. If you decide for gluing the wall holder, please be sure to provide for clean surfaces free from fat, oil and silicon lms and any other impurities. Remove completely the protective lm from the included adhesive pads, attach all the pads on the wall holder and then press the whole rmly to the required position. When mounting in colder temperatures, please remember that the full adhesive force cannot be achieved before 72 hours in 20 °C, with warmth accelerating the process (e. g. in 65 °C, the full adhesive force will be achieved in one hour). When gluing the holder plate on the colour sight protection lm, the above described conditions relating to cleanliness of surfaces and rmness of the adhesive pad should be observed.

To provide for a bubble-free application of the colour sight protection lm, please proceed as follows:

• Pour some water with a couple of drops of dishwashing detergent into a glass, stir it cautiously free of foam, and then use it to moisture gently the surface, on which the lm is to be applied.

• At an edge, pull off the white protective sheet from 1 cm of lm and straighten it out. To change the position, lift this surface carefully and attach it again as required.

• Then swipe the adhesive lm, e. g. with a plastic spatula, out from the contact surface in the direction of protective sheet still attached.secuENTRY easy English | 37 Attention! Do not use more liquid than absolutely necessary.

• Slide the keypad in from above until the locking peg of the mounting plate engages into the keypad housing. In this way, the keypad is protected against undesired removal.

• Perform a function test of the unit with the door open. For this purpose, enter repeatedly a valid opening code (e. g. PIN code, ngerprint, …).

Battery replacement for the secuENTRY easy keypad

• Remove the housing cover on the bottom side by loosing the 2 screws (Tx 8).

• Pull the battery compartment lid downwards until it disengages and replace the batteries.

When inserting the new batteries, be careful to observe the correct polarity as indicated on the housing.38 | English secuENTRY easy

• To close the battery compartment, rst press the battery compartment lid close to the screw holes to make them slide into the recesses, then snap the bottom side into position by pressing on it.

• Fasten the battery compartment lid with screws

Attention! Make sure that no moisture enters the keypad when replacing the battery. Cleaning instruction secuENTRY easy keypad The surface nish of the keypad prevents adherence of impurities. Dust or dirt can be removed from the surfaces using a damp cloth. No alcohol-based detergents (spirit, SIDOLIN

etc.) or aggressive detergents (acetone etc.) may be used, as they can damage the surface or the sensor. Replacement of batteries – knob (inner side) 1 Using the attached hex key, loose the top locking screw on the cylinder cover. It can be turned out only up to the opening of the cover and will not fall out. 2 Open the cover 3 Replace the batteries. Make sure the batteries are inserted with the correct polarity, indicated at the marked point on the housing.secuENTRY easy English | 39 4 Replace the cover. Emergency key function (outer side) Using the mechanical emergency key, you can provide access in case of failure of the system. 1 Swing the emergency key open and then insert it into the indicted slot in the cover panel. 2 Turn the key 90° clockwise. If required, move the outer knob slightly to the right and left in order to release the mechanism. 3 Turn the outer knob. The lock opens when fully turned at the latest. Turn the key to its initial position and take it out. To close the emergency lock, the knob shall be turned twice fully in both directions.40 | English secuENTRY easy Dismantling of secuENTRY easy keypad from wall holder

• Remove the housing cover on the bottom side by loosening the 2 screws (Tx 8).

• Pull the battery compartment lid downwards until it disengages and replace the batteries.

• Press the latch using a narrow tool (e. g. at-bladed screwdriver) downwards and slide the keypad upwards.

Interference from Bluetooth devices Bluetooth devices use the same frequency band (2.4 GHz) as WiFi devices. This can cause interference leading to errors or even to communication failure. In such case, any devices not required should be kept disconnected from power.secuENTRY easy English | 41 Warranty In order to be able to provide you with perfectly awless and high quality products and an optimal support when you need servicing or repair, we need you to present faulty or defective devices to your vendor together with a valid administrator code and the QR code(s), with the original purchase document attached. When you return a device component based on your right of withdrawal from the purchase agreement, such component shall be adjusted to factory settings and the seal on the cylinder and on the knob shall be intact. In case of noncompliance with this, the warranty becomes invalid. Disposal Dear customer, Please help us avoid unnecessary waste. Should you intend to dispose of this device at any time, please remember that many components of this device contain valuable materials, which can be recycled. Please be aware that electrical and electronic equipment and batteries shall not be disposed of as household waste, but rather collected separately. Please obtain information on the collecting points for electrical waste from the responsible authority of you municipality.

4.3 KitKat of 5.0 Lollipop, Apple iPhone 4S, 5, 5S, 6, 6P of later,