IAN 271517 - Motorcycle helmet CRIVIT - Free user manual and instructions

Brand	CRIVIT
Model	IAN 271517
Product type	Open-face motorcycle helmet
Available sizes	S (55-56 cm), M (57-58 cm), L (59-60 cm), XL (61 cm)
Safety standard	ECE-R 22.05
Shell material	High-strength ABS (HCM – High Density Copolymer Matrix)
Visor	DS-VISOR305 type, anti-scratch coating
Inner lining	Moisture-wicking Coolmax® fabric
Antibacterial treatment	HeiQ® Fresh Tech (silver on silicon dioxide)
Closure	Clip-on chin strap (quick-release buckle)
Ear pads	Removable with snap buttons
Acoustic cushion	Removable for noise reduction
Glasses compatibility	Yes
Shell cleaning	pH-neutral detergent, soft cloth, no solvents
Padding cleaning	Hand wash ≤30°C, air dry
Spare parts available	Visor (DS-VISOR305), ear pads, acoustic cushion, padding
Warranty	3 years (material and manufacturing defects)
Manufacturer	DELTA SPORT HANDELSKONTOR GMBH

Frequently Asked Questions - IAN 271517 CRIVIT

How to choose the right helmet size?

Measure your head circumference with a tape measure. Refer to the size chart: S (55-56 cm), M (57-58 cm), L (59-60 cm), XL (61 cm). Try on the helmet: it should fit snugly without being too tight; the skin at the temples may redden slightly.

How to clean the visor?

Wipe the visor with a soft, damp cloth to remove dirt (insects, dust). Dry with a soft, dry cloth. Never use solvents or abrasive products. In case of rain, dry it immediately.

How to change the visor?

To disassemble: press and turn the inner cover plates (1a) counterclockwise, remove the plates (1a and 1b), then detach the visor (1c). To assemble: position the visor on its support (1d), snap the outer plate (1b) onto the visor (L side on left), then snap the inner plate and turn clockwise.

How to adjust the chin strap?

Use the strap closure (III.B): press until you achieve a firm but comfortable fit. The sliding buckle secures the excess strap. The chin strap must be tight: you should barely be able to slide a finger underneath.

What to do after an impact or fall?

Replace the helmet immediately, even if it does not appear damaged. The internal structure may be compromised and will not protect effectively in a second impact.

How to maintain the inner lining?

Hand wash the ear pads and padding at below 30°C with a mild soap. Air dry at room temperature, away from heat sources. Never use solvents or petroleum-based products.

Can I paint or put stickers on the helmet?

No, any modification of the shell or addition of stickers is not allowed. This could compromise the helmet's protective properties.

How to store the helmet?

Store it in a dry, well-ventilated place at room temperature. Avoid direct sunlight, heat sources, and exhaust pipes. Do not carry it hanging from the motorcycle.

What is the warranty period and how to use it?

The helmet has a 3-year warranty from the date of purchase for material and manufacturing defects. Keep the receipt. Contact customer service: France 0800 919270, Belgium 070270171 (€0.15/min), or by email [e-mail] / [e-mail].

Where can I order a replacement visor?

You can order the DS-VISOR305 visor up to 5 years after purchase from customer service at the indicated contact. Use only original parts.

USER MANUAL IAN 271517 CRIVIT

Instructions for use

图图

SEHELM

GebruksachwZing

②

HELMA

Novod k pouzh

图图

Before recing, fold out the ilustration page and get to know all of the functions of your unit.

00

G/IE Usage and safety information Page 09

You have chosen to purchase a high-quality product. Familiarise yourself with the product before using it for the first time.

Read the following instructions for use carefully.

Use the product only as described and only for the given areas of application. Store these instructions for use carefully. When passing the product on to third parties, please also hand over all accompanying documents.

Parts Overview (Fig. A)

Visor Mechanism
2 Chin Straps with Snap Fastener
3 Ear Pad
4 Acoustic Damping
5 Inner Lining
6 Visor

Scope of Delivery

The scope of delivery for your helmet consists of the following:

• Acoustic Damping
• Helmet Bag
• Instructions for Use

Important Information

Our helmets are manufactured in accordance with the latest technology and are specifically designed for motorcycling. Whether the owner deems them to be suitable for any other use, is up to him. Wearing a helmet does not exclude the possibility of injury should an accident occur.

To guarantee adequate protection this helmet must be well fitting and securely fastened.

Every helmet that is exposed to a hard blow must be replaced.

We guarantee that this item is free of production and material defects. The guarantee does not apply to normal wear and tear and in case of improper use.

Instructions for Use

Safety Advice

• The helmet must fit tightly and the chin strap be closed.
• Always ensure that there is no airflow restriction inside the helmet.
• Ensure that your visor is clean and scratch-free at all times. Exchange damaged visors for a genuine replacement immediately. You are able to obtain replacement visors from the stipulated service address for a period of 5 years from the purchase date. Visor type: DS-VISOR305
• Never modify the helmet, its structure or the individual components.
• The helmet may not be painted or have stickers or labels.
• The helmet is designed to absorb the energy of a blow or a collision by destroying some of its components. In case of a further blow it wouldn't protect you any longer. After an accident, the helmet must be replaced even though it doesn't show external damages.
• Refrain from transporting your helmet by hanging it onto any part of your motorcycle. Keep it away from exhaust pipes and other sources of heat.
• Never clean the helmet with solvents containing petroleum or scouring agents, neither the outside nor the inside.

Always use pH-neutral detergent dissolved in clean water. Careful rub with a soft cloth. Then wipe dry with a lint-free cloth.

The pad may be cleaned with a little soap using a soft brush.

• Only use genuine spare parts for your helmet.

Product Characteristics

ECE-R 22.05 Homologation

This helmet is in compliance with ECE-R 22.05 standards and is homologised accordingly. The ECE-R 22.05 standard consists of uniform conditions for the approval of

protective helmets and its visors for drivers and passengers of motorcycles and mopeds.

The basic principles for these tests are the so called ECE-Regulations of the Economic Commission for Europe.

Significant Tests of the ECE-Regulation 22.05

• Shock absorbance
• Dynamic test of wear features
  Field of vision test
• Design strength
• Sustainability test (Strip-off test)
• Chin straps and lock test
  Shear test for outside edges
• Friction performance test of the outer shell
• Visor test

(mechanical and visual characteristics)

Inside Padding with Coolmax Inserts

Coolmax® by INVISTA is a high-performance fabric fibre

that supports its wearers during sport activities. Based on the patented DuPont-fibre technology, Coolmax® transports moisture from the body to the fabric surface where it dries quicker than with any other fabric.

The specially developed fibres of INVISTA that are used for Coolmax®-fabrics transport the moisture away from the body to the surface of the fabric where it has the opportunity to evaporate quickly. At the same time, the uniquely formed fibres offer maximum breathing activity, even in wet conditions. In addition, the breathing activity improves the heat regulating effect. Ear and forehead pads on this product are equipped with Coolmax®.

HeiQ® Fresh Tech

Textile freshness

Experience the feeling of

lasting freshness through the power of silver, keeping you odour-free all day long. The helmet liner contains a biocide agent (HeiQ Fresh Tech) for an anti-bacterial, odour-inhibiting lining treatment. Active ingredient: silver adsorbed to silicon dioxide (nano).

High-strength HCM outer shell

High Density Copolymer Matrix: High quality ABS plastic is formed under extreme heat and pressure to make a robust and impact-resistant outer shell.

Visor with anti-scratch coating

Suitable for eyeglass wearers

Safety lock closure

Date of manufacture (month/year): 11/2020

Use and Installation Instructions

Snap-Fastener System (Fig. B)

The snap-fastener enables an individual and quick vernier adjustment of the chin strap. Press the snap-fastener together until the helmet is sitting comfortably but firm.

The movable buckle may be used to fasten or secure excess chin strap.

Ear Pad (Fig. C)

The ear pads (3) are secured to the helmet with two press studs. The pads may simply be pulled out.

You must hear each press stud lock when securing the ear pads inside the helmet.

Acoustic Damping (Fig. D)

The acoustic damping (4) is for noise reduction, in particular when driving at high speeds. Press the acoustic damping into the cavity of the cheek pads. The acoustic side pad equipped with Velcro faces towards the helmet shell.

Visor Replacement (Fig. E) Removing the visor

Press and turn the cover plate (1a) on both sides counterclockwise to release. Remove the inner (1a) and outer cover plate (1b) and remove the visor (1c).

Installing the visor

Position the visor on the visor holder (1d) and place the outer cover plate over the visor.

Note: Be sure to attach the outer cover plate labelled "L" to the left side of the helmet.

Attach the inner cover plate to the outer cover plate and secure the visor by simultaneously pressing and turning clockwise.

Selecting the correct helmet size

• Measure the circumference of your head and select the helmet size based on this measurement. Try out several helmets before deciding. Ideally, the skin on your temples will move along when wearing the helmet.
• Ensure that even without the chin strap secured, the helmet does not move much on your head.
• The chin strap must be closed firmly for a secure fit. It is fitted correctly if it is difficult to slide your fingers under the chin strap. However, you must still be able to comfortably breathe, swallow and turn your head.
• Verify the helmet was tested according to the latest ECE standard.

Size table

Size Head circumference

S 55-56cm

M 57-58cm

L 59-60cm

XL 61cm

Maintenance and Care

Regular maintenance and care contributes to safety and maintaining the helmet.

Cleaning of the Helmet

• Never use solvents, petrol or other detergents when cleaning the shell and interior of your helmet.
• Always use pH-neutral detergent dissolved in clean water. Careful rub with a soft cloth. Then wipe dry with a lint-free cloth.

Visor care and cleaning

After using the helmet, lightly wipe off any grime (e.g. dead insects, dirt, sand, dust etc.) from the visor with a soft cloth and then fully wipe it clean using a dry soft cloth.
- When the visor gets wet (e.g. rainwater) it should always be wiped with a soft cloth.
- When cleaning the visor, never use any petroleum-based solvents or detergents containing abrasives.

Cleaning of the Ear Pads and Acoustic Damping

• Hand wash below 30^ .
• Allow to dry at room temperature.
• Avoid sources of heat.
• When not in use, store in a dry, well ventilated place.

Storage

When not in use, store the helmet in a dry and well ventilated place at room temperature. Avoid sources of heat. Do not needlessly expose the item to heat, e.g. in the car in hot outside temperatures.

Disposal

Dispose of the article and the packaging materials in accordance with current local regulations. Packaging materials such as foil bags are not suitable to be given to children. Keep the packaging materials out of the reach of children.

Dispose of the products and the packaging in an environmentally friendly manner.

The recycling code is used to identify various materials for recycling. The code consists of the recycling symbol - which is

meant to reflect the recycling cycle - and a number which identifies the material.

Notes on the guarantee and service handling

The product was produced with great care and under constant supervision. You receive a three-year warranty for this product from the date of purchase. Please retain your receipt.

The warranty applies only to material and workmanship and does not apply to misuse or improper handling. Your statutory rights, especially the warranty rights, are not affected by this warranty.

With regard to complaints, please contact the following service hotline or contact us by e-mail.

Our service employees will advise as to the subsequent procedure as quickly as possible.

We will be personally available to discuss the situation with you.

Any repairs under the warranty, statutory guarantees or through goodwill do not extend the warranty period. This also applies to replaced and repaired parts. Repairs after the warranty are subject to a charge.

IAN: 344829_2004 (Size S)

IAN: 344835_2004 (Size M)

IAN: 344828_2004 (Size L)

IAN: 344833_2004 (Size XL)

Service Great Britain

Tel.: [phone]

E-Mail: [e-mail]

Service Ireland

Tel.: [phone]

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (off peak))

E-Mail: [e-mail]

Felicitations!

Vizier met anti-scratch-coating

společenstvi (Economic Commission for Europe).

Podstatná przyzkoušeni podle ECE ustanoveni 22.05

Vymena viziru (obr. E)

Demontáž vizíru