OSWA0980WIT - Basket Pelgrim - Free user manual and instructions

USER MANUAL OSWA0980WIT Pelgrim

▷ Switching on the fan and increase the ventilation level. ▷ Connect the remote control to the built in unit. ▷ Switching on the timer. The fan switches off automatically after 10 minutes.

▷ Switching on and dim the lighting. ▷ Switching off the lighting.

▷ Reduce the ventilation level. ▷ Activate or switch off the carbon filter cleaning indicator. ▷ Reset of the cleaning indicator.

▷ Switching off the fan. ▷ Switching on the Clean Air function. The fan switches on automatically for 10 minutes every hour at level 1, 2 or 3.

5. Automatic mode button

▷ Connect to a hob. ▷ Enable or disable automatic mode Led status bar on the built in unit

Remote control Connecting the remote control to the appliance If the appliance cannot be operated with the remote control, e.g. after the battery has been changed, the connection between the remote control and the appliance must be re established.

1. Press and hold the ‘+’ button.

2. Attach the appliance to the mains voltage.

▷ A long audible signal sounds. The remote control has been connected to the appliance. Note: If no audible signal sounds within 30 seconds, repeat this procedure. Operation Switching on the extraction

1. Press the ‘+’ button.

▷ The extraction starts at level 2. ▷ On the led status bar the lighting of level 1 and 2 comes on. Adjusting the extractor capacity

1. Press (several times) the ‘-’ or ‘+’ button to select a higher or lower

setting (0-1-2-3-P). ▷ The maximum setting you can select is the intensive setting P (setting 4). On the led status bar the lighting of level 1, 2 and 3 comes on and setting P is blinking. ▷ The run time of the intensive setting is 4 minutes. Once this time has elapsed, the fan switches to level 2. Switching off the extraction

1. Press the off button.

▷ The extraction switches off. Switching the lighting on and off

1. Press the lighting button.

▷ The lighting comes on.

2. Press the lighting button again and the lighting fades to off.

OPERATIONEN 7 OPERATION Dimming the lighting

1. To dim the lighting, press and hold the lighting button until the

dimmer function is activated. ▷ The lighting comes on at maximum intensity and it decreases as long as you hold down the button. ▷ At lowest dimmer setting the light will go back from dimmed light to brighter light. Clean Air function The fan automatically switches on for 10 minutes every hour at the selected speed.

1. Switch off the appliance and lighting.

2. Press the off button.

▷ The extraction level starts at level 1. ▷ On the led status bar the lighting of level 1 comes on.

3. Press the ‘+’ button (several times) to select a higher setting

4. Confirm the selected setting within 5 seconds: press the off button

again. ▷ The Clean Air function is switched on. ▷ The lights of the selected level will blink on the LED status bar.

5. Press any button (except the lighting button) to switch off the Clean

Air function. Timer function With the timer function, the cooker hood can be switched off automatically after 10 minutes at level 1, 2 or 3.

1. Switch on the cooker hood and select a level (1, 2 or 3).

▷ On the LED status bar the lighting of the selected level will come on.

2. Press the ‘+’ button for 1.5 seconds until an audible signal sounds

twice. ▷ On the led status bar the lighting of the timer indication comes on. ▷ The timer function is active.

3. Switch off the timer function at any time by pressing the ‘+’ button

again for 1.5 seconds until an audible signal sounds.EN 8 If you change the level (to 1, 2 or 3) during the timer function, the timer function will remain active. Grease filter cleaning indicator After 100 hours of use of the cooker hood, on the LED status bar the lighting of the filter indicator is on and level 1 and 2 are blinking when the cooker hood is switched off. The grease filter must be cleaned.

• To reset the cleaning indicator, touch the ‘-’ button with the cooker hood switched off (motor off). ▷ You will hear a long confirmation beep. ▷ After 20 hours, the filter cleaning indicator automatically resets. Carbon filter cleaning indicator After 400 hours of use of the cooker hood, on the LED status bar the lighting of the filter indicator is on and level 3 and P are blinking when the cooker hood is switched off. The carbon filter must be cleaned.

• To reset the cleaning indicator, touch the ‘-’ button with the cooker hood switched off (motor off). ▷ You will hear a long confirmation beep. ▷ After 20 hours, the filter cleaning indicator automatically resets. If the cleaning indicator for both the grease filter and the carbon filter is displayed and the beep sounds, the reset procedure must be carried out twice. Activation of the carbon filter cleaning indicator In standard mode, the carbon filter cleaning indicator is not active. If the cooker hood is used as a recirculation hood, the carbon filter OPERATIONEN 9 cleaning indicator must be activated.

1. Switch off the cooker hood and the lighting.

2. Press and hold the ‘-’ button for four seconds.

▷ You will hear a long beep and on the LED status bar the indications of level 1, 2, 3, P and the filter saturation will come on for five seconds as confirmation. Switching off the carbon filter cleaning indicator:

1. Switch off the cooker hood and the lighting.

2. Press and hold the ‘-’ button for four seconds.

▷ You will hear a long beep twice and on the LED status bar the indications of level 1 and 2 and the filter saturation will come on for five seconds as confirmation. Battery replacement

1. Remove the two screws from the remote control backside.

2. Replace the battery (type “23A”).

▷ The battery is chemical waste and should be transported in a responsible way in accordance with government regulations. OPERATIONEN 10 Making the connection between cooker hood and hob The connection to an AutoAir hob is not active by default. First the connection to the hob must be activated. At the same time, a setting must also be made on the hob; see the hob manual for this. Check our website for the full range of hobs that can be connected to your cooker hood. Making a connection

1. Turn off the hood and the lighting.

2. Touch and hold the automatic mode button for three seconds.

▷ On the LED status bar the automatic mode indicator and the timer indicator will flash simultaneously for a maximum of two minutes.

3. On your hob, activate the pairing mode in the user menu (see the

hob manual). The connection to the hob is established. ▷ The connection is successful when on the LED status bar the automatic mode indicator and the timer indicator are illuminated continuously for four seconds. If the automatic mode indicator and the timer indicator are no longer illuminated within two minutes, the connection was not successful. Repeat the procedure. If necessary, clear the hood’s memory (see “Disconnecting”). Disconnecting

1. Turn off the hood and the lighting.

2. Touch and hold the automatic mode button for three seconds.

▷ On the LED status bar the automatic mode indicator and the timer indicator will blink five times simultaneously. ▷ The hob is no longer connected.

OPERATION WITH A CONNECTED HOBEN 11

Automatic mode The hob can control the extraction of the cooker hood in 3 different ways: manually, semi-automatically, and fully automatically. The automatic mode is for the user who wants the extraction level to automatically adjust to the cooking intensity. Extraction starts automatically as soon as a cooking zone is active and the extraction level depends on how the hob is used. When the hob is switched off, the extraction continues for 10 minutes and then stops automatically. Automatic mode Cooking zone setting Speed

Semi-automatic mode Cooking zone setting Speed

Switching on/off the automatic mode on the cooker hood The indicator for the automatic mode on the cooker hood only lights up when the hob is active and set to automatic mode. The hood is switched on and on the hob the automatic mode is active.

1. Shortly press and release the automatic mode button.

The automatic mode indicator iluminates; the automatic mode on your cooker hood is now switched on.

2. Shortly touch and release the automatic mode button.

The automatic mode indicator is no longer iluminated; the automatic mode on your cooker hood is switched off.

OPERATION WITH A CONNECTED HOBEN 12

Activated intensive setting on the hob If the intensive setting for the hood has been set on the hob, it will automatically switch back to speed 3 after six minutes. Activated timer function on the hob If the timer for the hood is set on the hob, the hood will continue to operate at speed 1 (according to the countdown time that is displayed) after switching off the hob until the set time has elapsed. Lighting When a connected hob is switched on, the lighting of the cooker hood always switches on automatically. You can continuously adjust the brightness of the hood via the hob. When you use the hob again (after you have switched the hob off) , the lighting comes on at the preset brightness. When switching off a connected hob, the lighting of the cooker hood remains on. Manually switch off the lighting with the lighting key on your AutoAir hob or via your hood.

OPERATION WITH A CONNECTED HOBEN 13

Cleaning Attention! For all maintenance first switch off the mains power to the built in unit by pulling the plug out of the socket or by turning off the home’s master switch. The built in unit needs to be cleaned regularly, both inside as well as outside. Do not use abrasive cleaners. Do not use alcohol! Attention! If the instructions regarding cleaning the appliance or replacing the filters are not followed, this can cause a fire. These instructions should be followed! The manufacturer is not liable for damage to the built in unit or fire damage resulting from incompetent maintenance or from non-adherence to the recommendations above and delivered safety instructions. Clean the built in unit with soapy water and a soft cloth. Then wash off with clean water. Do not use aggressive cleaning agents such as caustic soda and do not use scouring pads. Finish with a non-abrasive, non-polishing agent and buff the stainless steel in the direction of the grain. Metal grease filters Metal grease filters should be cleaned once a month (or when indicated by the filter saturation indication system, if present on your model), using a neutral cleaning agent, preferably by hand or in the dishwasher on a short, low-temperature program. Place the grease filters with the openings facing downwards in the dishwasher so the water can drain out of the filter. Aluminum-colored and black grease filters become dull as a result of dishwasher cleaning agents. This is normal and does not effect the working. The degree of saturation of the filter depends on the intensity of use, the manner of cooking and the regularity with which the grease filters are cleaned. MAINTENANCEEN 14 Grease filter Removing cassette filter

1. Switch off the motor and lighting.

2. Push in the latches and open the panel.

3. Open the filter’s access latch. Support the filter with your hand.

4. Remove the filter from the built in unit.

Cleaning The filters can be cleaned in the dishwasher. Allow the filters to drain well before replacing. The filters can also be cleaned by hand. Clean the filters in soapy water with washing up liquid and rinse. Allow the filters to drain well. See page 8 for instructions. The underside of the built in unit can be cleaned with a mild cleaning agent and a damp cloth. Dry off with a paper towel. Replacing cassette filter The filter should be placed with the locking mechanism on the front. Open the filter access latch. The notches at the front of the filter will then slot in. Hold the access latch in this position when placing the filters.

1. Slot the notches at the back of the filter in the specially designed

opening of the built in unit.

2. Tilt the filter upwards.

3. Release the filter access hatch. The notches at the back of the filter

will extend outwards and slot into the specially designed openings of the built in unit. The filter is now in position again.

4. Press the edge extraction panel firmly in the seal again (you will

hear a click). It is important that the grease filters are thoroughly dry before repositioning. PUSH PUSH PUSH PUSH MAINTENANCEEN 15 MAINTENANCE Carbon filter [optional] For recirculation purpose you can choose for washable carbon filters or for plasma filtering. The carbon filters can be regenerated.

1. Remove the filter matrass from the filterframe and clean the matrass

in the dishwasher, without detergent.

2. Dry the filtermatrass in the oven for 1 hour at a max. temperature of

3. Place the filters back afterwards.

Plasma filter [optional] Instead of using washable carbon filters, this built in unit can be operated with a plasma filter as well. See installation steps on how to install this. Make sure there are no carbon odourfilters installed when using a plasma filter. Lighting This hood is fitted with a light system. This light system has to be replaced by an authorized technician. Do not attempt to replace it by yourself. The lamp in this household appliance is only suitable for illumination of this appliance. The lamp is not suitable for household room illumination. PUSHPUSHEN 16 ENVIRONMENTAL ASPECTS Disposal of packaging and appliance This appliance is made from sustainable materials. This appliance must be disposed of in a responsible manner at the end of its service life. Contact the local authorities for information about the method. The packaging of the appliance is recyclable. The following materials may have been used:

• CFC-free polystyrene (hard PS foam). These materials must be disposed of in a responsible manner and in accordance with government regulations. The appliance is marked with a crossed out wheeled bin symbol to draw your attention to the requirement for the separate disposal of domestic electrical appliances. This means that the appliance may not be disposed of in unsorted household waste at the end of its service life. The appliance must be taken to a special municipal waste processing location for separated waste or to a dealer who provides this service. Collecting and disposing of domestic appliances separately avoids detrimental consequences for humans and the environment. This ensures that the materials used to make the appliance can be recovered and that substantial savings in the use of energy and raw materials can be achieved. Declaration of conformity We hereby declare that our products conform to the applicable European Directives, Regulations and requirements, as well as all requirements in the standards to which reference is made.EN 17EN 18EN 19872196 / VER 1 / 16-11-2021