PSS 65 B1 - Sharpener PARKSIDE - Free user manual and instructions

USER MANUAL PSS 65 B1 PARKSIDE

Scharfstation / Tool Sharpening Station / Affuteuse PSS 65 B1

DE AT CH

Scharfstation

Tool Sharpening Station

Translation of the original instructions

NL BE

Slipstation

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

FR BE

GB/IE Translation of the original instructions Page

General description. 20

Scope of delivery 20

Function description. 20

Summary 20

Technical specifications 20

Safety Instructions. 21

Symbols and icons 21

General Safety Instructions for Power Tools 21

Further Safety Instructions 23

Residual risks. 24

Assembly. 24

Setting up 24

Mount the sharpener 24

Operation 25

Switching on and off 25

Sharpening drills. 25

Sharpening picks and chisels. 26

Sharpening knives. 26

Sharpening scissors 27

Changing the grinding wheel 27

Cleaning and maintenance.....27

Cleaning. 28

Storage. 28

Waste disposal and environmental protection .28

Replacement parts/accessories...28

Trouble Shooting 29

Guarantee 30

Repair Service. 31

Service-Center 31

Importer 31

Translation of the original EC declaration of conformity ....105

Exploded Drawing 111

Introduction

Congratulations on the purchase of your new device. With it, you have chosen a high quality product.

During production, this equipment has been checked for quality and subjected to a final inspection.

The operating instructions constitute part of this product. They contain

important information on safety, use and disposal.

Before using the product, familiarise yourself with all of the operating and safety instructions. Use the product only as described and for the applications specified.

Keep this manual safely and in the event that the product is passed on, hand over all documents to the third party.

Intended use

The sharpening station is suitable for sharpening tools (e.g. drills, knives, scissors, picks, chisel).

The device is not intended for all other types of applications (e.g. grinding with unsuitable grinding tools, grinding with a coolant solution, grinding hazardous materials such as asbestos).

The equipment is intended for use in the field of DIY. It is not designed for commercial use.

The equipment is designed for use by adults. Young people over the age of 16 are permitted to use the equipment only under supervision.

The manufacturer shall not be liable for damages caused by use other than for the intended purpose or by incorrect operation.

General description

The illustrations can be found on the front and rear fold-out pages.

Scope of delivery

Unpack the equipment and check that it is complete. Dispose of the packaging material correctly.

• Appliance
  Sharpener for knives and scissors
• Sharpener for drills
• Sharpener for picks and chisels
• Spare grinding wheel
• Instruction Manual

Function description

The sharpening station is suitable for sharpening tools (e.g. drills, knives, scissors, picks, chisels). The scope of delivery contains three sharpeners for this purpose, which, as a guide and safety device, enable precise sharpening and grinding. Refer to the following descriptions for a functional description of the controls.

Summary

1 Mains plug

Sharpener for knives and scissors

3 On/off switch
4 Spacer
5 Magnet holder
6 Tool table
7 Retaining screw for angular adjustment
8 Protective hood
9 Mounting holes for work bench assembly
10 Grinding wheel

1.1 rotatable drill mount
12 Knurled nut for drill-fastening
13 Release lever for sharpener
14 Drill holder
15 Adjusting device
16 Grinding wheel nuts

Technical specifications

Tool sharpening station..PSS 65 B1

Nominal

input voltage 220 - 240 V~, 50 Hz Power consumption ... 65 W (S2 10 min)*

Measurement idling speed n_0 6700 Safety class

Protection category.. IP 20 Weight

(incl. accessories) approx. 1.37 kg Grinding angle range. 15^ - 50^

Sharpness drill diameter.3-10 mm Sharpness knife width.. 6-51 mm Grinding wheel

Outer diameter 49.5 mm

Borehole diameter. 10.14 mm

Thickness 7.9 mm

Abrasive Diamond

Base body.. Metal

Working speed....... max. 60~m / s

Rotational speed.....max.23100 min-1 Sound pressure level

(L_pA) 59.3 dB(A); K_pA = 3 dB

Sound power level

(L_WA) 73.5 dB(A); K_WA = 3 dB

• A break is introduced after 10 minutes of uninterrupted operating duration until the device temperature differs 2K (2^) less than room temperature.

Noise and vibration values have been determined according to the standards and regulations mentioned in the declaration of conformity.

Safety Instructions

Symbols and icons

Symbols on the device:

Warning!

Read the instruction manual.

Wear ear protection.

Risk of electric shock! Disconnect from the mains before carrying out maintenance and repair work.

Safety class II (Double insulation)

Do not dispose of electrical equipment in household waste.

Drill diameter

Grinding wheel nut

Grinding angle

Workpiece size

For grinding

knives and scissors

Rotatable drill retainer

Symbols in the manual:

Warning symbols with information on damage and injury prevention.

Instruction symbols with information on preventing damage.

Connect the machine to the power supply.

Pull out the mains plug.

Wear ear protection

Help symbols with information on improving tool handling.

General Safety Instructions for Power Tools

WARNING! Failure to follow the safety instructions and guidelines may result in electric shock, fire and/or serious injuries.

Please read all these instructions before using this electric tool and please keep the safety instructions.

The term "power tool" used in the safety instructions refers to mains-operated electric tools (with a mains cable) and to battery-operated electric tools (without a mains cable).

Safe operation:

• Keep work area clear. Cluttered areas and benches invite injuries.

• Consider work area environment.

• Do not expose tools to rain.

• Do not use tools in damp or wet locations. Water entering a power tool will increase the risk of electric shock.
• Keep work area well lit.
• Do not use tools in the presence of flammable liquids or gases.

Power tools create sparks which may ignite the dust or fumes.

• Guard against electric shock.

Avoid body contact with earthed or grounded surfaces (e.g. pipes, radiators, ranges, refrigerators).

• Keep other persons away.
  Do not let persons, especially children, not involved in the work touch the tool or the extension cord and keep them away from the work area.
• Store idle tools. When not in use, tools should be stored in a dry locked-up place, out of reach of children.
• Do not force the tool. It will do the job better and safer at the rate for which it was intended.

• Use the right tool.

• Do not force small tools to do the job of a heavy duty tool.

• Do not use tools for purposes not intended; for example do not use circular saws to cut tree limbs or logs.

Use of the power tool for operations different from those intended could result in a hazardous situation.

• Dress properly.

• Do not wear loose clothing or jewellery, they can be caught in moving parts.

• Anti-slip footwear is recommended when working outdoors.

• Wear protective hair covering to contain long hair.

• Use protective equipment.

• Use safety glasses.

• Use face or dust mask if working operations create dust.

• Connect dust extraction equipment. If the tool is provided for the connection of dust extraction and collecting equipment, ensure these are connected and properly used.

• Do not abuse the cord. Never yank the cord do disconnect it from the socket. Keep the cord away from heat, oil and sham edges.

• Secure work. Where possible use clamps or a vice to hold the work. It is safer than using your hand.

• Do not overreach. Keep proper footing and balance at all times.

This enables better control of the power tool in unexpected situations.

• Maintain tools with care.

Many accidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean for better and safer performance.
• Follow instruction for lubricating and changing accessories.
• Inspect tool cords periodically and if damaged have them repaired by an authorized service facility.
• Inspect extension cords periodically and replace if damaged.

• Keep handles dry, clean and free from oil and grease.

• Disconnect tools. When not in use, before servicing and when changing accessories disconnect tools from the power supply.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

• Remove adjusting keys and wrenches. Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Avoid unintentional starting. Ensure switch is in "off" position when plugging in.
• Use outdoor extension leads. When the tool is used outdoors, use only extension cords intended for outdoor use and so marked.
• Stay alert, watch what you are doing and use common sense when operating a power tool.

Do not use a power tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention white operating power tools may result in serious personal injury.

• Check damaged parts. This will ensure that the safety of the power tool is maintained.

• Before further use of tool, it should be carefully checked to determine that it will operate properly and perform its intended function.

• Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation.
• A guard or other part that is damaged should be properly repaired or replaced by an authorized service centre unless otherwise indicated in this instruction manual.

• Do not use the tool if the switch does not turn it on and off.
  Have defective switches replaced by an authorized service centre.
  There is a risk of injury.

• Warning. The use of any accessory or attachment other than one recommended in this instruction manual may present a risk of personal injury.

• Have your tool repaired by a qualified person. This electric tool complies with the relevant safety rules. Repairs should only be carried out by qualified persons using original spare parts, otherwise this may result in considerable danger to the user..

Further Safety Instructions

• Connect the device only to a power point with a RCD (Residual Current Device) with a measured residual current of not more than 30mA .
• Keep the mains cable and extension cable away from the grinding disk and

saw chain. In the event that it is damaged or severed, immediately disconnect the plug from the socket.

Do not touch the cable before it has been disconnected from the mains. Risk of electric shock.

The replacement of the plug or the cable must be carried out by the manufacturer or his/her customer service in order to avoid any hazards.
Only switch the device on once it is safely fixed to the worktop.
- For your own safety only use accessories and attachments which were stated in the operating instructions or recommended or specified by the tool manufacturer.
- Only use grinding wheels where the printed rotational speed is at least as high as what has been specified on the name plate of the device.
- Carry out a visual inspection of the grinding wheel before use. Do not use any damaged or deformed grinding wheels. Replace any damaged or worn grinding wheels.
- Make sure that the sparks produced by grinding do not present a danger, e.g. reach people or ignite flammable substances.
- Never keep the fingers between the grinding wheel and spark protection or in close proximity to the protective hoods. There is a risk of crushing.
- The rotating parts of the device cannot be covered due to functional reasons. Therefore, proceed cautiously and hold the workpiece firmly in order to avoid slipping which could cause your hands to come into contact with the grinding belt or grinding wheel.
- The workpiece gets hot during grinding. Do not touch the machined area, allow it to cool down. There is a risk of burning. Do not use coolants or the like.

GB E

If you are tired or have consumed alcohol or tablets, do not work with the device. Always have a break on time.
- Switch the device off and remove the mains plug

• to loosen a blocked insertion tool,
• if the connection line is damaged or entangled,
• in case of unusual sounds.

Residual risks

Even if properly operating and handling this electric tool, some residual risks will remain. Due to its construction and build, this electric tool may present the following hazards:

a) Lung damage, if suitable respiratory protection is not worn.
b) Hearing damage, if suitable ear protection is not worn.
c) Damages to health due to touching the area of the grinding tool which was not covered; the ejection of pieces from workpiece or damaged grinding wheels.
d) Damage to your health caused by swinging your hands and arms when operating the appliance for longer periods of time or if the unit is not held or maintained properly.

Warning! During operation, this electric tool generates an electromagnetic field which, under certain circumstances, may impair the functionality of active or passive medical implants. To reduce the risk of serious or lethal injuries, we recommend that persons with medical implants consult their doctor and the manufacturer of their medical implant before operating the machine.

Assembly

Caution! Risk of injury!
- Ensure that you have sufficient space in which to work, and that you do not endanger other people.

• All covers and protective devices must be assembled properly before commissioning.
• Disconnect the mains plug before changing the setting on the device.

Setting up

Place the sharpening station on firm surface and fasten the device. Ideally, bolt the drill to the surface. Use the mounting holes for the work bench assembly (A 9) in the baseplate for this.

The screws and nuts required for assembly are not part of the scope of delivery.

Mount the sharpener

1. Select one of the three sharpeners.
2. In order to remove a sharpener from the working position, you must press down the release lever for the sharpener (A 13).
3. Remove the sharpener from the guide rails, upwards.
4. In the storage positions, the sharpeners are not fixed to the right and left side and can be easily removed from the guide rails.
5. In order to fasten the selected sharpener in the working position, from above push this into the guide rails. Press the sharpener down until it snaps into place.

The sharpeners also present a safety device. Never use this device without a sharpener. Risk of injury!

Operation

Caution! Risk of injury!

• Always disconnect the plug from the mains socket before working.
• Use only grinding disks and accessories recommended by the manufacturer. The use of other insertion tools and other accessories may cause risk of injury.
• Never operate the device without the visual protection disk.
• Switch on the equipment only when it is safely installed on the work surface.

Despite spark protection, always wear safety goggles while working in order to avoid eye injuries.

We recommend wearing ear protection to prevent damage to hearing.

Keep your hands away from the grinding wheel and grinding belt when the device is in operation. Injury hazard.

Switching on and off

Ensure that the mains voltage matches the specifications on the rating plate.

Connect the equipment to the mains.

1. To switch on, press the "I" On switch and the device starts up (see A 3).
2. To switch off, press the "0" off switch and the device switches off (see A 3).

After switching on the device, wait until the device has reached its max. speed. Only then must you start with the grinding.

The disk will continue to run after the equipment is switched off. There is a risk of injury.

Test run:

Before starting work and after each change of grinding disk, carry out a test run of at least 60 seconds with no load. Switch off the equipment immediately if the disk runs lumpy, substantial vibrations occur, or abnormal noises are generated.

Sharpening drills

Drills with a diameter of 3 - 10mm can be sharpened.

1. Mount the selected sharpener (see Mounting sharpener).
2. Remove the drill holder (14) from the sharpener.
3. Insert the drill into the drill holder (14). Do not attach the drill.
4. Insert the drill holder (14) upwards into the adjusting device (15) using the knurled nut for drill-fastening (12).
5. Push the drill to the front into the V-nut up to the metal stop. The cutting edges of the drill must fit closely to the metal surfaces.

GBIE

1. Using the knurled nut fasten the drill for drill-fastening (12).
2. Remove the drill holder (14) and insert this into the rotatable drill mount (11) from below using the knurled nut for drill-fastening (12).
3. Check the alignment of the drill. The cutting edges of the drill must be touching the grinding wheel (10).
4. Switch the device on and grind the drill by moving the rotatable drill mount (11) to and fro in the direction of the arrow.
5. Switch the device off and wait for the grinding wheel (10) to stop.
6. Remove the drill holder (14) and insert it into the rotatable drill mount (11) by rotating in by 180^ . Using the same adjustment, you can grind the opposite cutting edge of the drill.
7. Switch the device off and grind the drill.
8. Switch the device off and wait for the grinding wheel (10) to stop.

C Sharpening picks and chisels

1. Mount the selected sharpener (see Mounting sharpener).
2. Place the blade on the tool table (6) so that it lies against the spacer (4). The magnetic holder (5) keeps the blade in position.
3. Release the retaining screw for the angular adjustment (7) and turn the tool table (6) into position. Select the angle according to the existing bevel angle (angle of the bevelled edge).
4. Tighten the retaining screw for angular adjustment (7) again.

5. Switch the device on and move the tool table (6) equally back and forth along the grinding wheel (10).

6. Always use light pressure while sharpening and slowly push the blade towards the grinding wheel (10).

7. Repeat the sharpening process until all irregularities have been removed.
8. Switch the device off and wait for the grinding wheel (10) to stop.

To sharpen a chisel, turn the chisel over and repeat the process from Point 5.

D Sharpening knives

The device is not suitable for grinding serrated knives.

1. Mount the selected sharpener (see Mounting sharpener).
2. Turn the machine on.
3. Insert the blade of the knife right into the grinding slot.
4. Using light pressing guide the blade along the grinding wheel (10) and evenly and slowly pull the knife towards you.
5. Turn the knife and insert the knife blade into the opposite grinding slot.
6. Repeat this grinding process for this side of the blade as well.
7. Execute the alternating grinding process until the cutting edge is burr-free and sharp.
8. Switch the device off and wait for the grinding wheel (10) to stop.

E Sharpening scissors

The device is not suitable for grinding serrated scissors. The device is not suitable for grinding pinking shears.

1. Mount the selected sharpener (2)(see Mounting sharpener).
2. Completely open the scissors.
3. Turn the machine on.
4. Insert one of the scissor blades into the grinding slot.
5. Using light pressure guide the blade from the screw up to the tip along the grinding wheel (10).
6. Remove the scissors from the sharpening station and turn the scissors to sharpen the other blade.
7. Insert the other scissor blade into the grinding slot.
8. Using light pressure guide the blade from the screw up to the tip along the grinding wheel (10).
9. Execute the alternating grinding process until the cutting edges are burr-free and sharp.
10. Switch the device off and wait for the grinding wheel (10) to stop.

Changing the grinding wheel

Information on replacement:

Never operate the device without protective equipment.

• Ensure that the grinding wheel dimensions match those of the device.

• Never use separate bushings or adapters in order to make grinding wheels whose hole is too large fit the device.

• Do not use any saw blades.
  Always reassemble the device completely after replacing the grinding wheel.

Switch the device off and remove the mains plug.

Allow the device to cool down.

When the grinding disc nut (16) is being tightened or loosened, the grinding disc (10) must be held firmly by hand or the axle held firmly in place with a pair of pliers.

1. Release the grinding wheel nut (16) in the clockwise direction (left-handed thread).

1. Remove the grinding wheel (10).
2. Set up a new grinding wheel (10). Screw the grinding wheel nut (16) in the anti-clockwise direction (left-handed thread).
3. Test run: Before starting work and after each change of grinding disk, carry out a test run of at least 60 seconds with no load. Switch off the equipment immediately if the disk runs lumpy, substantial vibrations occur, or abnormal noises are generated.

Cleaning and maintenance

Disconnect the plug before adjustment, maintenance or repair.

Have any work not described in these instructions carried out by a specialist workshop. Use only original components. Allow the equipment to cool before carrying out any maintenance and cleaning work. There is a risk of burns.

Before each use, check the equipment for obvious defects such as loose, worn or damaged components and check that screws or other parts are sitting correctly. In particular, check the grinding disk (A 10). Replace damaged parts.

Cleaning

Do not use cleaning agents or solvents. Chemical substances may attack plastic parts of the equipment. Never clean the equipment under running water.

• Clean the equipment thoroughly after each use.
• Clean the surface of the device with a soft brush or cloth.

Storage

• Store the appliance in a dry place well out of reach of children.
  Grinding disks must be stored dry and upright and are not to be stacked.

Waste disposal and environmental protection

Be environmentally friendly. Return the tool, accessories and packaging to a recycling centre when you have finished with them.

Machines are not to be place with domestic waste.

• Hand over the device at an utilization location. The plastic and metal parts employed can be separated out into pure materials and recycling can be implemented. Ask your Service Center about this.
  Defective units returned to us will be disposed of for free.

Replacement parts/ accessories

Spare parts and accessories can be obtained at www.grizzly-service.eu

If you have issues ordering, please use the contact form.

If you have any other questions, contact the "Service-Center" (see page 31).

Position Instruction manual	Position Exploded drawing	Description number	C
A 10	19+21	Grinding wheel with Grinding wheel nuts	91103590
A 2	25	Sharpener for knives and scissors	91103591
12	Sharpener for drills	91103592
	10	Sharpener for picks and chisels	91103593

Trouble Shooting

Always disconnect the plug from the mains socket before working.

Danger of electric shock.

Problem Possible Cause	Use Error correction
Device doesn’t start	Mains voltage missingMain circuit breaker is tripped	Check the socket, mains cable, line, mains plug, repairs to be carried out by qualified electrician if necessary, check main circuit breaker.
	On/off switch (A3) may be defective	Repair by Customer Care
	Engine faulty
Grinding tools do not move although the engine is running	Grinding wheel nut (A16) loose	Tighten grinding wheel nut (see „Changing the grinding wheel“)
	Workpiece, remaining workpieces or remaining grinding tools block drive	Remove blockages
Engine is slower and stops	Device is overloaded through workpiece	Reduce pressure on grinding tool
		Workpiece unsuitable
Grinding wheel does not rotate smoothly, abnormal noises can be heard	Grinding wheel nut (A16) loose	Tighten grinding wheel nut (see „Changing the grinding wheel“)
	Grinding wheel (A10) faulty	Change grinding wheel

Guarantee

Dear Customer,

This equipment is provided with a 3-year guarantee from the date of purchase. In case of defects, you have statutory rights against the seller of the product. These statutory rights are not restricted by our guarantee presented below.

Terms of Guarantee

The term of the guarantee begins on the date of purchase. Please retain the original receipt. This document is required as proof of purchase.

If a material or manufacturing defect occurs within three years of the date of purchase of this product, we will repair or replace - at our choice - the product for you free of charge. This guarantee requires the defective equipment and proof of purchase to be presented within the three-year period with a brief written description of what constitutes the defect and when it occurred.

If the defect is covered by our guarantee, you will receive either the repaired product or a new product. No new guarantee period begins on repair or replacement of the product.

Guarantee Period and Statutory Claims for Defects

The guarantee period is not extended by the guarantee service. This also applies for replaced or repaired parts. Any damages and defects already present at the time of purchase must be reported immediately after unpacking. Repairs arising after expiry of the guarantee period are chargeable.

Guarantee Cover

The equipment has been carefully produced in accordance with strict quality guidelines and conscientiously checked prior to delivery.

The guarantee applies for all material and manufacturing defects. This guarantee does not extend to cover product parts that are subject to normal wear and may therefore be considered as wearing parts (e.g. grinding wheels) or to cover damage to breakable parts (e.g. switches).

This guarantee shall be invalid if the product has been damaged, used incorrectly or not maintained. Precise adherence to all of the instructions specified in the operating manual is required for proper use of the product. Intended uses and actions against which the operating manual advises or warns must be categorically avoided.

The product is designed only for private and not commercial use. The guarantee will be invalidated in case of misuse or improper handling, use of force, or interventions not undertaken by our authorised service branch.

Processing in Case of Guarantee

To ensure quick handling of you issue, please follow the following directions:

• Please have the receipt and item number (IAN 344934_2004) ready as proof of purchase for all enquiries.

• Please find the item number on the rating plate.

• Should functional errors or other defects occur, please initially contact the service department specified below by telephone or by e-mail. You will then receive further information on the processing of your complaint.

• After consultation with our customer service, a product recorded as defective can be sent postage paid to the service address communicated to you, with the proof of purchase (receipt) and specification of what constitutes the defect and when it occurred. In order to avoid acceptance problems and additional costs, please be sure to use only the address communicated to you. Ensure that the consignment is not sent carriage forward or by bulky goods, express or other special freight. Please send the equipment inc. all accessories supplied at the time of purchase and ensure adequate, safe transport packaging.

Repair Service

For a charge, repairs not covered by the guarantee can be carried out by our service branch, which will be happy to issue a cost estimate for you.

We can handle only equipment that has been sent with adequate packaging and postage.

Attention: Please send your equipment to our service branch in clean condition and with an indication of the defect.

Equipment sent carriage forward or by bulky goods, express or other special freight will not be accepted.

We will dispose of your defective devices free of charge when you send them to us.

Service-Center

Service Great Britain

Tel.: [phone]

E-Mail: [e-mail]

IAN 344934_2004

Service Ireland

fei.: 1890 930 034

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (off peak))

E-Mail: [e-mail]

IAN 344934_2004

Importer

Please note that the following address is not a service address. Please initially contact the service centre specified above.

Garantie - France. 44

Slipstation...PSS 65 B1

Nominale

ingangsspanning .... 220 - 240 V~, 50 Hz

Krachtontneming .65 W (S2 10 min)*

(L_PA) 59,3dB(A);K=3dB

Geluidsvermogensniveau

(L_WA) 73,5dB(A); K_WA = 3 dB

Pobórmocy. 65 W (S2 10 min)*

Prędkość obrotowa

znamionowa n. 6700 min

(L_pA) 59,3dB(A);K=3dB

Noš okulary ochrone.

Uzywajśrodków ochry.

GB IE	Translation of the original EC declaration of conformity
We hereby confirm that the Tool sharpening station model PSS 65 B1
Serial number 000001 - 206217
conforms with the following applicable relevant version of the EU guidelines:
2006/42/EC • 2014/30/EU • 2011/65/EU*
In order to guarantee consistency, the following harmonised standards as well as natio- nal standards and stipulations have been applied:
EN 61029-1:2009/A11:2010 • EN ISO 12100:2010 • EN 13236:2019 EN 55014-1:2017 • EN 55014-2:2015 EN 61000-3-2:2014 • EN 61000-3-3:2013 • EN 62321-2:2014
This declaration of conformity is issued under the sole responsibility of the manufacturer:
CE	Grizzly Tools GmbH & Co. KG Stockstädter Straße 20 D-63762 Großbostheim, GERMANY 01.09.2020
	Christian Frank Documentation Representative

• The object of the declaration described above satisfies the provisions of Directive 2011/65/EU of the European Parliament and the Council of 8 June 2011 on limiting the use of certain harmful substances in electrical and electronic appliances.