Retro ToGo blender - Blender Witt - Free user manual and instructions

USER MANUAL Retro ToGo blender Witt

IMPORTANT SAFE INSTRUCTIONS: IMPORTANT: Please read the instructions (and particularly the safety instructions) carefully before using the device. Store these instructions and only transfer the product to others together with the instructions. SAFETY MEASURES GENERAL Using the product incorrectly may result in injuries to people or damage to the device.

• Only use the product for its intended purposes. The manufacturer is not liable for damage that occurs due to misusing the device or handling it incorrectly.

• Always place the product on a dry, level and stable surface at a good distance from the edge of the table, etc.

• The product is only intended for household use. The product may not be used for commercial purposes.

• The product may only be connected to a 220-240V 50/60Hz power source.

• The product’s motor/electronic components, cord and plug may never be lowered into water and water must not penetrate into the motor/electronic components.

• Never touch the product, cord or power socket with wet or moist hands.

• Never expose the product to direct sunlight, high temperatures, moisture, dust or acidic substances.

• Never leave the product when it is turned on.

• The product should be kept under constant supervision when it is being used. Children should always be supervised when the product is used to ensure that they do not play with the product. This product is not a toy.

• The product may contain sharp objects and should therefore be stored in a place that is inaccessible to children.

• Only use accessories that are included with the product or recommended by the manufacturer.

• The product may not be used by people with reduced sensitivity or physical or mental impairments or people who are not capable of operating the product unless they are supervised or instructed in how to properly use it by a person who is responsible for their safety.23 ENEN

• Do not led the cord hang out over the edge of the table.

• Keep the cord and the product away from heat sources, hot objects and open flames.

• Unplug the device before cleaning and if the device is not in use.

• Do not pull on the cord when unplugging - grab the plug itself.

• Make sure that the cord is completely rolled out.

• Regularly check to see if the cord or plug is damaged and do not use the product if this is the case or if it has been dropped on the floor, dropped into water or been damaged in some other way.

• If the product, cord or plug is damaged, the product must be inspected and if necessary repaired by an authorised specialist. Never attempt to repair the product yourself. Contact the place you bought the product from if the repair is covered by warranty. If unauthorised changes are made to the product, the warranty no longer applies. IMPORTANT SAFETY INSTRUCTIONS: You must always comply with the basic safety instructions, including the above, before using the blender.

1. Read all of the instructions first.

2. Before using the blender, you must verify that the voltage in your socket

matches the approved voltage of the device.

3. Do not use the blender if the cord or plug is damaged or if the device is not

working correctly or if it has been dropped or damaged in some other way. Return the device to the nearest authorised service centre for an inspection, repair or electronic or mechanical adjustment.

4. To reduce the risk of electric shocks, never operate the device with wet hands

and never spill fluids on the device or lower it into water or other fluids.

5. The device is not intended to be used by people (including children) with

reduced physical, sensory or mental capacities or by people who lack experience and knowledge unless they are supervised or instructed in how to sue the device by someone who is responsible for their safety.

6. Children must be supervised to ensure that they do not play with or touch the

7. Never leave the device unsupervised when it is being used.

8. Never place the device on or close to a hot gas stove or a heated oven.

9. May not be used outdoors. The device is only designed for household use.

10. Never use the device when the container is empty and do not remove the lid

on the container before the blade has come to a complete stop.24

11. Unplug the device when it is not being used and before installing or

dismantling parts or before cleaning.

12. Avoid touching moving parts.

13. Warning: Improper use of the product may result in serious injuries to

people. Be careful when handling the blade, especially when removing it from the container, when emptying the container and when cleaning it.

14. Do not stick your hands or kitchen utensils into the container while

blending as this may result in serious injury to people or damage to the product.

15. The blade is sharp. It must be handled with caution.

16. To avoid the risk of personal injury, you must never place the blade edge

on the motor unit without first attaching the lid to the blender container.

17. Only use the blender when a lid is attached to the container.

18. Only use the blender on a flat and even surface.

19. Never use accessories that are not mentioned in the instructions. This

includes glass jars and the like which are not recommended by the manufacturer. If you ignore this warning it may result in injuries to people.

20. Do not blend hot fluids.

21. Please ensure that the amount of ingredients does not exceed the max

marking on the container as this will impact the crushing effect and reduce the lifespan of the product.

22. Hard ingredients must be cut into small pieces before they are processed

to achieve a better crushing effect.

23. It is strictly forbidden to start the blade unit on the base when the blender

container is not filled.

24. If the desired effect is not achieved within 1 minute, take a break and wait

for 2 minutes before continuing with the blending. This helps to extend the lifespan of the product.

25. Do not let the blender container run while empty and do not overfill it.

The symbol means that the product should not be thrown out together with regular household waste. Instead, it should be disposed of at an authorised recycling station which is suitable for this purpose or returned to a retailer that offers disposal services. Contact your local municipality if you need more information.25 WHEN USING IT FOR THE FIRST TIME ENEN

• You must remove all packaging before using the Witt Retro To-Go blender for the first time.

• Be careful when handling the blades - they are very sharp.

• Clean the container, lid, blade unit and accessories with warm soapy water. Rinse and dry them thoroughly. All components (except the base/ motor unit) can be put in the dishwasher.

• When using your blender for the first time, there may be odours coming from the motor. This is normal and the odours will disappear as the blender is used. HOW YOUR WITT RETRO TO-GO BLENDER WORKS

1. Cut the ingredients into smaller pieces of approximately 1.5 cm and add

them to the blender container with a suitable amount of water. The total amount must not exceed the maximum marker (500 ml).

2. Install the blade unit’s waterproof sealing ring in the indentation/ridge on

the blade unit. The device will leak if this is not installed correctly. Then attach the blade unit firmly to the blender container. Please note: If the blade unit and blender container are not correctly attached or if the blade unit does not have a waterproof seal, the device may not work and the blade may get loose.

3. Now install the blender container with the blade unit firmly to the base/

motor unit itself. Make sure that the blade unit is firmly attached before turning the blender container to blend.

4. Connect the device to a power source and select the gear/speed and

then begin blending. Do not blend for more than 60 seconds at a time. Let the motor rest for two minutes before continuing.

5. When you are done blending: For safety reasons, the base must be

turned off at the socket and the plug must be removed. Wait a few seconds so that the blades have time to stop turning before lifting the blender container from the base.

6. Remove the blade unit and pour the ingredients out - or attach the

drinking lid and drink directly from to-go container.26

CLEANING AND MAINTENANCE

Always remove the plug from the socket before touching the base/motor unit.

Do not leave food residues to dry in the blender container or on the lid. If pos- sible, these steps should be taken immediately after using the blender:

• Rinse food remains off the blade, container and lid.

• The components should be washed in warm soapy water with a mild deter- gent or a soft sponge.

The base should be dried with a moist, soft rag and then dried thoroughly. Also dry off food residue/splash residue from the cord. CLEANING AGENTS Do not use grinding cleaning agents or scouring pads on either the base or the blender container as this may scratch and damage the surface and lead to permanent damage to the product. Only use warm soapy water with a soft sponge/rag. DISHWASHER The blender container, lid and blade unit can be put in the dishwasher. CITRUS If the blender container is exposed to citrus oil, it may affects its appearance and durability. After washing it with a cleaning agent, it must be rinsed thoroughly with clean water and dried immediately. Do not leave the container to soak if you have used citrus fruit as an ingredient. Do not install the blade unit while cleaning the blender with a cleaning agent. STORAGE Should be stored in an upright position with the container and blade unit assembled and on the base or next to it.27 ENEN TECHNICAL SPECIFICATIONS RESOLVING PROBLEMS The motor is not starting/the blade units are not rotating

• Ensure that the plug is correctly attached to the socket.

• The overload protection feature may have been activated (see below) The blender suddenly stops while it is being used

• The blender has an overload protection mechanism which prevents the motor from being damaged. Remove the plug from the socket and then remove the container and let the motor cool off for 30 minutes. Then you can use the blender normally again.

• We recommend that you blend smaller amounts or cut the ingredients into smaller pieces. The food is lumpy or uneven

• This can happen when too much is blended at once. Try to blend smaller amounts or blend the contents multiple times.

• The ingredients may be too large, try to cut them into smaller pieces. To get the best results, the pieces should not be larger than 2 cm. The food sticks to the container and blade

• The food may be too thick. Try to add more fluids. 1 220VAC 50Hz 300W 2 Capacity: 500 ml

There is a 2-year warranty period if your new product stops working due to manufacturing or material faults which begins from the documented date of purchase. The warranty covers materials and the cost of labour. When inquiring about service, please state the product name and serial number. You can find this information on the type plate. You can write down the information here in these instructions so that you have them at hand. This makes it easier for the service technician to find the correct spare parts. The warranty does not cover: - Faults and damage that are not due to manufacturing or material issues - Damage caused by failure to properly maintain the device - including failing to clean it - Fire and/or water damage or moisture damage on the product - Damage caused during transport if the product was transported without proper packaging - Damage caused by the use of unoriginal spare parts - Damage resulting from failing to follow the instructions on how to use the device - If the device has not been set up/assembled as specified in the instructions - If non-professionals have installed or repaired the product - Batteries or any other parts subject to normal wear and tear Damage during transport If the product is damaged during transport and this is discovered when the retailer delivers the product to the customer, this is exclusively a matter between the customer and the retailer. In cases where customers have handled the transport of the product themselves, the supplier shall not be liable for any potential damage during transport. Any damage caused during transport must be reported immediately and no later than 24 hours after the product has been delivered. If not, the customer’s claim will be rejected. Unnecessary service If the product is sent in to be serviced and it turns out that the fault could have been fixed independently by following the product’s instruction manual, the customer will need to pay the service fee. Commercial purchases Commercial purchases are all purchases of devices that are not intended to be used in private households but instead intended to be used for commercial purposes (in restaurants, cafés, canteens, etc.) or intended to be rented out or otherwise used by multiple users in turn. There is no warranty offered for commercial purchases, as this product is only intended for regular household use. SERVICE For service and spare parts in England and Ireland please call below-mentioned number and you will be directed accordingly or send us an email. Witt UK & Ireland Ltd. (44) 148 351 6633 / [e-mail] We accept no liability for printing errors. The manufacturer/distributor cannot be held liable for damage to products or individuals if the safety instructions were not followed. The warranty shall not cover cases where the instructions have not been followed.29 SESE