IAN 276362 - Faucet MIOMARE - Free user manual and instructions

Technical Features	MIOMARE IAN faucet, chrome finish, brass material, ceramic cartridge, standard water flow.
Usage	Designed for domestic use in the bathroom or kitchen, easy to install on a sink or washbasin.
Maintenance and Repair	Regular cleaning with a soft cloth, checking seals and replacing the cartridge in case of leaks.
Safety	Complies with current safety standards, lead-free, protection against overpressure.
General Information	5-year warranty, customer service available for assistance, compatible with standard plumbing systems.

Frequently Asked Questions - IAN 276362 MIOMARE

How to install the MIOMARE IAN 276362 faucet?

To install the faucet, start by turning off the water. Attach the faucet to the sink following the manual instructions. Ensure the seals are properly in place to prevent leaks.

What to do if the faucet leaks?

First, check that all connections are tightly secured. If the problem persists, it may be necessary to replace the seals or the faucet cartridge.

How to clean the MIOMARE IAN 276362 faucet?

Use a soft cloth and a non-abrasive cleaner to wipe the faucet. Avoid products containing acid or abrasive particles that could scratch the surface.

What is the recommended water pressure for the faucet?

The recommended water pressure for the MIOMARE IAN 276362 faucet is between 1 and 5 bars for optimal operation.

What to do if the water temperature is not adjustable?

Check that the hot and cold water connections are correctly installed. If the problem persists, it may be necessary to consult a plumber.

Where to find spare parts for the faucet?

Spare parts can be ordered from MIOMARE customer service or at specialized DIY stores.

Is the faucet guaranteed?

Yes, the MIOMARE IAN 276362 faucet is generally covered by a 2-year warranty against manufacturing defects. Keep your proof of purchase for any claims.

How can I adjust the water flow of the faucet?

The water flow can be adjusted using the flow regulator integrated into the faucet. See the user manual for more details on adjustment.

USER MANUAL IAN 276362 MIOMARE

Assembly, operating and safety instructions

NL BE

SPOELTAFEL-ARMATUUR

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

FR BE

links = rot (Warmwasser),

List of pictograms used

Introduction

Intended use Page 12

Parts description.. Page 12

Technical Data Page 12

Scope of delivery.

Safety notices.. Page 13

Installation

Start-up Page 14

Operation

Maintenance and Cleaning

Maintaining and cleaning the tap . Page 14

Replacing the cartridge . Page 14

Disposal

Information.

Potability of tap water.. Page 15

Warranty and Service

List of pictograms used
i	Read the instructions!	WARNING!	Potential of serious to fatal injuries.
!	Observe the warning and safety instructions!		Beware of electric shock!
	Risk of fatal injury and accidents for infants and small children!		Dispose of packaging and device in an environmentally-friendly way!

Kitchen Mixer Tap

Introduction

Congratulations on the purchase of your new product. You have selected a high quality product. The assembly and oper

ating instructions are part of this product. Before installation please read through the whole of these instructions and take note of the advice they contain before you start the installation. These instructions contain important information about installation, settings and care. Keep these instructions safe and if you pass on the product to anyone else please pass on the documentation as well.

Intendeduse

The product is only designed to regulate the hot and cold water flow. It is only intended to be installed in sink units. This product is suitable for use with all pressure-resistant hot water systems such as central heating, continuous-flow water heater, pressure boiler etc. It is not suitable for low pressure water heaters such as wood or coal burning bath geysers, oil or gas bath geysers, open electrically heated water tanks. When in doubt please consult a plumber or heating specialist. Any use not specified or product modification is prohibited and will result in damage. Any form of use other than the stipulated intended purpose can cause danger to life and cause injury. The product is for private use only and is not intended for medical or commercial use. The manufacturer accepts no responsibility if the intended purpose of this unit is not adhered to.

- Partsdescription

1

Spout
Fitting body
Fitting base ring
Plastic triangle
Threaded bolts
C sealing washer
C metal washer
Locknut
Aerator*
2 Flexible connecting hoses
Cartridge
Cartridge lock nut
Cartridge cover ring
Warm/cold plaque
Locking screw
Handle
Socket head wrench

• preinstalled

-TechnicalData

Connections: G 3/8

1

Minimum flow press

1.5 bar

- Scope of delivery

1 Sink unit single-lever mixer
1 Fastening set (3 - 8)
2 Flexible connecting hoses with seal 3 / 8'' (10)
1 Socket head wrench [17]
1 Instructions for assembly / operation

Safety notices

DARGIONING!

LIFE AND RISK OF ACCIDENTS FOR INFANTS AND CHILDREN!

Never leave children unattended with the packaging material. Suffocation hazard. Keep this product well away from children. This product is not a toy.

BEWARE OF ELECTRIC SHOCK!

Leaking or water discharge can lead to life-threatening danger due to electricity. Carefully check that all connections are tight. Also ensure that all wires of appliances are correct and have been installed.

CAUTION! RISK OF INJURY! Please ensure that no parts are damaged and that all parts are correctly assembled. Incorrect assembly could lead to injury. Please note that washers and gaskets are wear parts and therefore will need to be replaced from time to time.

Damaged parts could impact safety and function.

Be sure all seals are correctly seated.

CAUTION! Be careful not to reverse the hot / cold water plaque [14]. The correct position is: left = red (hot water), right = blue (cold water).

CAUTION! DAMAGE TO THE ARTICLE!

Please have all installations performed by skilled individuals.

Please note that the seals are wear parts and must be changed from time to time.

Any leakage or sudden escape of water can cause considerable damage to buildings and property. All connections must therefore be checked carefully to ensure that they are tight.

Familiarise yourself prior to installation with all local conditions, e.g. water connections and shut-off device.

The product is only suitable for use in rooms in which a temperature above 0^ is maintained.

Installation

Note: Familiarise yourself with the product prior to assembly. Carefully read the following assembly instructions and safety advice. In the event of incorrect installation, all warranty claims - particularly in relation to subsequent damage - are excluded.

CAUTION! Before you start installation turn off the water supply at the mains. Otherwise injuries and/or property damage may occur.

CAUTION! Do not twist or strain the connection hoses.

Note: This step requires a slot screwdriver and a SW 12 mm open-end spanner.

Follow these steps:

CAUTION! Be sure to only fasten the connecting hoses 10 hand tight (see Fig. A). Do not use pliers or a wrench. Otherwise the product could be damaged.

Screw the two connecting hoses 10 hand tight into the designated boreholes in the fitting body2 (see Fig.A).

Using a slot screwdriver tighten the threaded bolt 5 all the way into the fitting body 2 and remove the fastening nut 8. Attach the fitting base ring 3 to the fitting body 2.

Place the fitting body 2 and the fitting base ring 3 over the opening in your sink unit.

Under the washbasin unit, first place the plastic triangle 4, the C-seal 6 then the C-metal washer 7 over the threaded bolt 5.

Now screw the fastening nut 8 onto the threaded bolt 5 and tighten with an open-ended spanner SW 12 mm until the fitting is seated firmly on the sink unit.

Screw the flexible connecting hoses to the angle valves. Be sure to correctly install the flexible connecting hoses to the cold- / hot water hoses - left flexible connecting hose to the hot water connection, left angle valve, and the right flexible connecting hose to the cold water connection, right angle valve.

- Start-up

After the initial commissioning, carefully check all connections for leaks.

To remove any possible impurities the tap must be flushed before being used for the first time. To do this, proceed as follows:

Unscrew the aerator attachment and aerator 9 from the spout1.
Open the main water supply and allow the water to flow for two minutes to flush out any residues.
Screw the aerator attachment and aerator back onto the spout 1.

Operation

Note: If the tap has not been used for a long period, flush the pipes thoroughly to avoid stagnation and build-up of residue.

Open the main water supply.
Lift the handle 16 and swing it to the right or left in order to regulate the speed or temperature of the water.

Hot water:

Swing the handle to the left.

Cold water:

Swing the handle 16 to the right.

Check operation of the mixer. To do so, swing the handle 16 into all permissible positions. Please regularly check the connections are tight.

- Maintenance and Cleaning

- Maintaining and cleaning the tap

Please note that sanitary taps require special care and attention. Therefore, please follow the instructions:

Never clean with petrol, solvents or harsh cleaners or hard cleaning brushes, etc. These can damage the product surface.
Dry your taps with a cloth after every use in order to avoid the build-up of any limescale.
Clean the product with a damp, soft cloth and, if necessary, mild detergent.
Unscrew the aerator attachment and aerator 9 at regular intervals and remove any limescale deposits or foreign bodies. In the event of excessive dirt or damage replace the the aerator attachment and aerator 9 with a new one.

Note: The aerator attachment and aerator can normally be unscrewed by hand. Otherwise you can carefully use a pipe wrench and you must lay a thin, damp cloth around the aerator attachment and aerator so that you do not damage it. A pipe wrench with plastic jaws is also suitable.

Non-observation of the above care advice can be expected to result in damage to the surfaces of the product. This will inevitably invalidate the guarantee.

- Replacing the cartridge

A cartridge 11 is a wear part that needs replacing according to the hardness and / or degree of contamination of the water. This becomes evident when the handle 16 becomes difficult to move. A new cartridge 11 can be obtained from the listed service office.

Note: This step requires an open-end spanner SW 27 mm or fitting pliers.

Proceed as follows to replace the cartridge 11

Shut off the main water supply. Allow any remaining water in the pipework to drain.
Remove the hot / cold plaque [14] by adjusting the handle [16] to the highest position and inserting a flat object between the edge of the hot / cold plaque [14] and the outside of the handle [16]. Note: Use light pressure to carefully push the hot / cold plaque [14] outward so as not to scratch the surface.
Loosen the locking screw 15 with the socket head wrench by turning it counter-clockwise.

CAUTION! Do not completely unscrew the locking screw 15. Only loosen this as far as is necessary to remove the handle 16.

Remove the handle 16
Unscrew the cartridge covering ring [13] do not use pliers or a spanner. Otherwise the product could be damaged.
Loosen the cartridge locknut 12 below with fitting pliers or an open-end spanner SW 27mm and remove the entire cartridge 11 from the fitting body 2.
Insert the new cartridge into the fitting in the same manner.

Note:Be sure the seal under the cartridge 11 is correctly seated. Make sure that the guides are in the corresponding holes.

Reassemble all the above parts. Tighten the cartridge lock nut using fitting pliers or an open-end spanner SW 27 mm while simultaneously securing the fitting from twisting. This will achieve tightness and ensure the handle is not difficult to move.

CAUTION! Be careful not to reverse the hot /

cold water plaque14. The correct position is: left = red (hot water), right = blue (cold water).

Disposal

The packaging is made of environmentally friendly materials, which may be disposed of through your local recycling facilities.

Contact your local refuse disposal authority for more details on how to dispose of your worn-out product.

Information

- Potability of tap water

Find out about the potability of your mains water supply. Your local water authority / water supply company will be able to inform you.

The following general recommendations apply to the potability of tap water:

Let the water run freely for a short time if it has been stagnating in the pipework for more than four hours. Do not use any of this stagnant water in the preparation of food or for drinking. This applies particularly as far as babies and infants are concerned. Health concerns may otherwise arise. Fresh water can be readily distinguished from stagnant water as fresh water is noticeably cooler as it leaves the pipe.
- Do not use stagnant water from chromium-plated pipework to prepare food, for drinking, or for personal hygiene if you are allergic to nickel. This water may contain high quantities of nickel and trigger an allergic reaction.
- Do not use water from lead pipework for preparing food baby food and / or to prepare foods during pregnancy. Lead dissolves in drinking water and is particularly damaging to the health of babies and young children.

Warranty and Service

The warranty period is 5 years and begins on the day of purchase. Please keep your receipt as proof of purchase.

However, if defects do occur during the warranty period, after first contacting service the defective fitting may be returned freight forward to the service address specified. You will then receive a new or repaired fitting free of charge.

After the warranty period has expired you may also send the defective fitting to the address specified for repair. Repairs made after the expiration of the warranty period are subject to payment.

Note: Eisl Sanitär GmbH will replace defective fittings or supply the respective replacement parts free of charge within the warranty period. Eisl Sanitär GmbH is unable to refund the purchase price for defective fittings.

Warranty and Service

This warranty does not limit your legal rights.

The warranty period will not be extended by repairs made under warranty. This applies also to replaced and exchanged parts. Complaints are often initiated by difficulties encountered during use. Many of these complaints can be resolved by telephone or email. Please contact the service address set up for you before filing a warranty claim for the fitting with the manufacturer:

GB,IE:

Sanifix Limited

Unit 68 Morgan Close

Willenhall

West Midlands

WV124LH

United Kingdom

Tel.: [phone]*

E-Mail: [e-mail]

• Free of charge number

IAN 276362

Please have the receipt and item number, e.g.

IAN 12345 ready as your proof of purchase when making an enquiry.

Product description:

Kitchen Mixer Tap

Eisl sanitary No.

NI182DISE-LIDL3

PRENEZ GARDE AU RISQUE

LE- WAARSCHUWING! VENSGEVAAR EN GEVAAR VOOR ONGEVALLEN VOOR

OHROZENI ZIVOTA A ZRANE-NI MALYCH A VETSICH DETI!