Lithium Barba MB350LC - Beard trimmer REMINGTON - Free user manual and instructions

USER MANUAL Lithium Barba MB350LC REMINGTON

Thank you for buying your new Remington® product. Please read these instructions carefully and keep them safe. Remove all packaging before use. IMPORTANT SAFEGUARDS

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been supervised/instructed and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children unless they are older than 8 and supervised.

• Always check the appliance before you use it. Do not use the appliance if it is damaged, as this may cause injury.

• The adaptor contains a transformer. Do not cut off the adaptor to replace it with another plug, as this causes a hazardous situation.

• Check if the voltage indicated on the adapter corresponds to the local mains voltage before you connect the appliance.

• Only use the adapter supplied to charge the appliance.

• Always replace a damaged adaptor with one of the original type.

• Keep the appliance and the adapter dry.

• This appliance should never be left unattended when plugged into a power outlet, except when charging.

• Do not plug or unplug the appliance with wet hands.

• Do not use attachments other than those we supply.

• This appliance is not intended for commercial or salon use. The blades are washable under a running tap.

• Please note the main body of the trimmer is not washable and should be kept away from water. ENGLISH5 ENGLISH

5. Charging connector

10. Cleaning brush (not shown)

11. EDGEStyler (not shown)

CHARGING YOUR APPLIANCE

Before using your trimmer for the rst time, charge for 4 hours.

1. Ensure the product is switched o.

2. Connect the charging adaptor to the product and then to the mains.

3. The charging indicator will illuminate.

Charge Level Indicator light While charging Green LED will ash Fully Charged Green LED will come on Low Charge Red LED will come on

• Your trimmer cannot be overcharged. However, if it is not going to be used for an extended period of time (2-3 months), unplug it from the mains and store.

• To preserve the life of your batteries, let them run out every 6 months then recharge for 4 hours.

• On a full charge, your beard trimmer will run for up to 60 minutes of cordless usage. CORDED

• Connect the appliance to the mains and turn on.

• We recommend you let the product charge for a few minutes before using corded. CAUTION: Extended mains only use will result in the reduction of the battery life.

• Hold the trimmer in one hand with your thumb rmly on the zoom wheel to keep it from turning. Ensure the length position indicator is at 1.

• Slide the comb down the grooves until it clicks into place.

• The comb can only be attached one way.

ADJUSTING THE TRIM LENGTH

• The trimmer comb can be adjusted to give you 9 dierent trim lengths simply by turning the wheel to the desired setting.6 ENGLISH

• Turn the wheel clockwise for shorter length, anti-clockwise for longer length.

• The wheel will click into place as it reaches each setting and the setting number will appear on the length position indicator. Setting Description Hair length mm inch 1 Stubble or cropped look 1.5 0.06

2. Use the zoom wheel to set the comb to the desired length setting.

3. The setting will appear on the length position indicator. If you are trimming for the rst

time start with the maximum trimming length setting.

4. Turn the unit on.

5. Place the at top of the trimmer comb against the skin.

6. Slowly slide through the hair. Repeat from dierent directions as necessary.

7. If hair builds up in the trimmer comb during the trimming process, switch the unit o,

pull the comb and brush the hair o. Note: Use the beard trimmer without the adjustable comb for trimming hair close to the skin. This will trim hair to 1mm, holding the blades perpendicular to the skin will trim hair to 0.4mm.

TRIMMING THE NAPE OF YOUR NECK

Note: you will need a hand mirror for this operation if performing it alone.

1. Remove the adjustable comb.

2. Use your ngers to lift the hair at the base of your head up o the neck. Your index

nger should be covering the roots of the hairs you are lifting to prevent accidental removal by the beard trimmer.

3. Using your other hand, hold the trimmer to the base of your neck with the cutting unit

facing up and move the trimmer up the length of the neck until it touches your nger covering the hair roots at the base of your head.7 ENGLISH

4. Be sure to move the unit slowly when performing this operation and to keep the roots

at the base of your head out of the way of the trimmer.

TO DEFINE THE BEARD/MOUSTACHE LINE

1. Hold the trimmer with the trimmer blade facing you.

2. Start with the edge of beard/moustache line and gently lower the trimmer blade onto

3. Use motions towards the edge of the beard/moustache line to trim to desired locations

in facial area and away from beard in neck area. BLADE RELEASE

1. Ensure the trimmer is switched o.

2. Remove the adjustable comb.

3. Remove the blades by pushing your thumb upwards under the blades and move the

blade set away from the trimmer body.

4. To reattach the blades, align the back of the blades with the back housing at the top of

the trimmer and push down until the blade set clicks into place.

TIPS FOR BEST RESULTS

• Beard, moustache and sideburn hairs should be dry.

• Avoid using lotions before use.

• Comb your hair in the direction that it grows. USING THE EDGEStyler The EDGEStyler tool is used to guide your trimmer to create a symetrical, dened edge to your beard. Neck Line (Fig. A) Hold the appropriate curved side of the tool underneath your jaw and run your trimmer along it for a clean edge. Repeat on the other side then even up the remaining V left under the chin freehand. Cheek (Fig. B) Hold the appropriate curved side of the tool against the cheek and run your trimmer along it for a clean edge. Repeat on the other side of your face. Sideburn (Fig. C) Use the straight edge of the tool against the sideburn for perfect, straight edges. Moustache (Fig. D) Use the curved edge of the tool to sculpt the moustache area.8 ENGLISH

CARING FOR YOUR TRIMMER

• To ensure long lasting performance of the trimmer, clean the blades and unit regularly.

• Ensure the appliance is switched o and unplugged from the mains.

• Do not use harsh or abrasive cleaners on the unit or blades.

• This product has washable blades. Ensure the blades are detached from the trimmer before washing the blades.

• Wash the blades under a running tap to remove any hair clippings.

• After rinsing under a tap ensure the blades are dry.

• Do not rinse while the product is connected to the mains.

• Please note the main body of the trimmer is not washable and should be kept away from water.

• After each use, it is recommended to clean hair from the blades either by rinsing the blades or using a cleaning brush. BATTERY REMOVAL The appliance must be disconnected from the supply mains when removing the battery.

1. Turn the trimmer on and discharge all remaining power.

2. Remove the comb and cutter assembly.

3. Use a screwdriver to pry out the holder plate under the trimmer carefully.

4. Use a screwdriver to pry the two side panels carefully.

5. Remove the 4 screws from the housing.

6. Using a screwdriver carefully pry apart the top and bottom housing.

7. Unscrew the 2 screws on the circuit board.

8. Remove the upper circuit board.

9. Disconnect the battery from the low circuit board.

• Used batteries must be removed from the appliance and disposed of at an appropriate ocial recycling/collection point. RECYCLING

9. Adapter (ikke vist)

• This product may only be used with the charging adapter supplied.

• You must always replace a damaged adapter with an original.

• Keep the device and adapter dry.

The blades are washable under a running tap.