SBCSC367/05U - Baby monitor PHILIPS - Free user manual and instructions

USER MANUAL SBCSC367/05U PHILIPS

Guarantee certificate

Identificatiekaart

Portugues

Garantibevis

Certificat de garantie

Dealer's name, address and signature

This document is printed on chlorine free produced paper

Data subject to change without notice

Printed in China

€0682

baby monitor

SBC SC367

Instructions for use

I-1 Microphone high-sensitivity microphone
1-2 Power light lights when unit is powered; flashes when batteries are low
1-3 Transmit light - lights when a sound is being transmitted
I-4 Talk pushbutton push this button to talk in intercom mode
1-5 Loudspeaker provides clear sound
1-6 Loudspeaker volume control --- set loudspeaker level for talk-back and intercom
I-7 DC power supply socket ---- plug mains adapter connector into this socket
I-8 Mode switch

MONITOR : baby monitoring mode; microphone is sound activated

OFF: switches off the Baby unit completely

INTERCOM : microphone is activated when TALK pushbutton (1-4) is pressed

I-9 Channel selection switch --select channel A or B (whichever has least interference)
1-10 Battery compartment cover ---- unscrew and unclip to insert batteries
I-11 AC power adapter plug into AC mains socket and into DC power supply socket
1-12 Temperature indication approximate baby room temperature in ^ C

PARENT UNIT

• set loudspeaker level for monitoring and intercom;
• switches off the power to the unit completely

2-1 Microphone sensitive talk-back and intercom microphone
2-2 Power light - lights when unit is powered; flashes when batteries are low
2-3 Link light - lights to show that both units are in touch with each other
2-4 Loudspeaker provides clear sound for monitoring and intercom modes
2-5 Loudspeaker Volume control / Off switch
2-6 Sound-level lights the more sound your baby makes, the more lights that light
2-7 Charging base place unit in base to operate it on mains power and when batteries are low
2-8 Battery compartment cover ---- unscrew and unclip to replace batteries
2-9 Talk pushbutton push this button to talk in talk-back and intercom modes
2-10 Channel selection switch select channel A or B (same as Baby unit)
2-11 Belt clip handy clip for carrying the unit
2-12 DC power supply socket ---- plug mains adapter connector into this socket
2-13 AC power adapter plug into AC mains socket and into DC power supply socket
2-14 Audible warning switch --- sets audible link alarm on or off
2-15 Charging base light - lights when unit is in the base and charging

CONGRATULATIONS

You have just purchased a high-performance, cordless Baby Monitor that lets you listen to your child from wherever you are in and around the house. You can also use the monitor to comfort your baby with the talk-back function or as a two-way intercom. Please read this guide carefully before using the monitor, and keep it for future reference.

IMPORTANT!

This Baby Monitor is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such.

Make sure the Baby unit and adapter cable are always out of reach of the baby, at least 1 metre away.

Never place the Baby unit inside the baby's bed or playpen!

The antennas on the Parent and Baby units are fixed; do not try to extend them.

Never cover the Baby unit (with a towel, blanket, etc.)

GETTING THE UNITS READY FOR USE

Baby unit

Connect the AC power adapter (1-11) to an AC mains socket, and then connect the cord to the DC power supply socket (1-7) of the Baby unit.

If you want to use batteries, remove the battery compartment cover (1-10) using a screwdriver. Insert four 1.5V, AA batteries (not included; we recommend non-chargeable Philips Alkaline batteries), noting the + and - configuration inside the battery compartment. Put the cover back in place and tighten screw.

The Baby unit operates cordlessly for up to 30 hours on fresh batteries. The red POWER light (1-2) flashes when battery power is low. If this happens install new batteries.

Note: To switch off the Baby unit completely set the mode switch (1-8) to OFF.

Parent unit

The Parent unit uses rechargeable batteries. These are already installed, but first they must be charged for at least 14 hours as follows before using the unit outside the charging base:

• Connect the AC power adapter (2-13) to an AC mains socket, and then connect the cord to the DC power supply socket (2-12) of the charging base (2-7).
• Place the Parent unit inside the charging base. The red charging light (2-15) lights.

The Parent unit can be operated now but you should leave it in the charging base until the batteries are fully charged (at least 14 hours). When the batteries are fully charged, take the Parent unit out of the charging base and use cordlessly for up to 12 hours.

When the red POWER light (2-2) on the Parent unit flashes, the battery power is low. Place the Parent unit inside the charging base to recharge the batteries.

If the rechargeable batteries begin to lose their effectiveness, replace them with four new batteries (1.2V, AA NiMH) as follows: remove the battery compartment cover (2-8) using a screwdriver and insert the batteries noting the + and - configuration inside the battery compartment. Put the cover back in place and tighten screw. Only use 1.2V, AA NiMH rechargeable batteries!

Monitoring baby's sounds

To use the units to listen to your baby:

• Position the Baby unit at least 1 metre away from the baby so that the microphone (1-1) can pick up baby's sounds.
• Set the channel switch to the same position on both units.
• Set the mode switch on the baby unit (1-8) to MONITOR.
• The green TRANSMIT light (1-3) lights when a sound is picked up.
• Move away from the Baby unit with the Parent unit.
• Switch on the Parent unit using the Volume control/Off (2-5) and adjust the volume to the level you prefer.

The green LINK light (2-3) lights continuously when the Parent unit and the Baby unit are in touch with each other.

Talking back to your baby

Use the talk-back facility on the Parent unit to comfort your baby:

• Set the mode switch on the baby unit (1-8) to MONITOR.
• Use the VOLUME control (1-6) of the Baby unit to set the loudspeaker level to about mid-range.
• Switch on the Parent unit using the Volume control/Off (2-5).
• Press and hold the TALK pushbutton (2-9) on the Parent unit and talk clearly into the microphone (2-1).
• Release the TALK pushbutton when you are finished.

Adjust the volume of the Baby unit loudspeaker to the level you prefer using the VOLUME control (1-6) on the Baby unit.

Note: While the TALK pushbutton on the Parent unit is being pressed, sounds from the Baby unit cannot be heard on the loudspeaker of the Parent unit.

Two-way intercom

To use the units as a two-way intercom:

• Set the mode switch on the baby unit (1-8) to INTERCOM.
• Use the VOLUME control (1-6) of the Baby unit to set the loudspeaker level to about mid-range.
• Switch on the Parent unit using the Volume control/Off (2-5) and adjust it to about mid-range.
• On the Parent unit, press and hold the TALK pushbutton (2-9) and talk clearly into the microphone (2-1). Release the button when you are finished.
• On the Baby unit, press and hold the TALK pushbutton (1-4) and talk clearly into the microphone (1-1). Release the TALK pushbutton when you are finished.

Note: While the TALK pushbutton on either unit is being pressed, a signal from the other unit cannot be heard. In other words, only one person should speak at a time.

Avoiding interference

Both units use anti-interference technology to reduce the chance of interference from other signals. If interference does occur or if sound reception is poor, try switching both units to the other channel to improve the sound quality.

Note: Always make sure that the channel selection switches (1-9, 2-10) on both units are set to the same position.

Sound-level lights

The Parent unit has sound-level lights (2-6), which visually alert you to baby's sounds even when the volume control is turned down. The louder the sound received from the Baby unit, the more lights light.

Checking that the units are in touch

The green LINK light (2-3) of the Parent unit lights continuously to show that the Parent unit and the Baby unit are in touch with each other. This light flashes if the Baby unit is out of range for more than 30 seconds or if the signal is blocked.

When the units are no longer in touch, try one of the following:

• Move the Parent unit closer to the Baby unit. (The maximum operating distance is 250m in ideal conditions. Walls and floors can limit this distance.)
• Switch both units to the other channel.
• Check that both units are powered correctly (low batteries?).

Switching on the audible warning

If you wish, you can switch on a special feature that lets you hear an audible warning on the Parent unit when the units are not in touch. The Parent unit is delivered with this beep switched off to avoid intermittent disturbances that can occur when the connection is interrupted for a short period.

To switch on the audible warning, open the Parent unit's battery compartment cover (2-8) and set the switch (2-14) inside to the On position ( ).

Note: The LINK light (2-3) continues to flash even if the audible warning is switched off.

Baby room temperature

The Baby unit has a thermometer strip (1-12) that measures the temperature in the room. The approximate room temperature, in ^ C , is indicated by a change in colour.

Belt clip

When the batteries of the Parent unit are charged, the unit can be carried around giving you freedom of movement while still monitoring your baby. Use the belt clip (2-11) to attach the unit to your clothing and so keep your hands free. The belt clip can be removed by unclipping the top and sliding it downwards.

PROBLEM SOLVING

Problem	Possible Cause	Solution
Power light does not light.	Parent unit
	Unit is not turned on.	Turn Volume control/Off switch clockwise (2-5).
	Batteries are low.	Recharge batteries.
	Baby unit
	Unit is not turned on.	Set microphone switch (1-8) to the MONITOR position.
	AC adapter is not plugged in or Batteries are exhausted.	Plug in AC adapter or replace batteries.
	AC adapter plugged into an outlet that is not working.	If the power socket has a switch, turn it on.
High pitched noise.	Units are too close together.	Move Parent unit away from Baby unit.
	Volume too high.	Turn volume control on Parent unit counter-clockwise.
Parent unit batteries do not charge.	Battery life is at an end.	Replace rechargeable batteries, using only 1.2V, AA NiMH batteries.
No sound.	Volume control on Parent unit is set too low.	Turn volume control/Off switch clockwise (2-5).
	Units are out of range.	Move Parent unit closer to Baby unit.
Power light blinking.	Batteries are low or empty.	Parent unit:- recharge batteries. Baby unit:- replace batteries or connect to mains power.
Talk-back / intercom function not working*.	Loudspeaker volume on Baby unit is too low.	Set volume control (1-6) on Baby unit to mid-range.
Interference or poor reception.	Mobile or cordless phones too close to the baby monitor can cause interference.	Move the phones away from the units.

• With the talk / intercom function if either the Parent or Baby unit is transmitting, then the other unit can only receive and not transmit.

TECHNICAL SPECIFICATIONS

Power supply

• Batteries 4 x 1.2V AA; rechargeable NiMH for Parent Unit (included);
• Optional batteries 4 × 1.5 ~V ; AA alkaline for Baby Unit (not included);
• AC power adapter 230V AC, 50Hz (two included): - Output voltage 9V DC, 200mA .

Only use the AC power adapter included or a type that complies with safety standard EN60950 and that has the following specification: 9 Volt DC / 200mA.

Operating range

• up to 250 metres in ideal conditions
• 10^ to 40^

Pilot tone

• Continuous communication link (hidden signal ensures a continuous link between both units so you only hear your baby's sounds).

Transmission frequencies

	Channel A	Channel B
SBC SC367/86U & SBC SC367/87U:	40.695 MHz	40.675 MHz
SBC SC367/05U (IRE, UK):	49.890 MHz	49.830 MHz
SBC SC367/13U (SE):	27.145 MHz	27.095 MHz
SBC SC367/16U (ES):	31.350 MHz	31.000 MHz

UNITE BÉBÉ

I-1 Micrófono micrófondo de alta sensibilitad
1-2 Luz testigo de alimentacion activada cuando la unidad está encendida; intermitente cuando la potencia de las pilas está baja
1-3 Luz testigo de transmisión activada cuando se está transmitido
I-4 Botón pulsador de haberdo ---- pulsar este botón para saber en modo de intercomunicación bidirectional
I-5 Altavoz proportiOna sonido claro
I-6 Mando de volumen del altovoz --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- intercomunicacion bidireccional
I-7 Enchufe de alimentacion de CC -- conectar el adaptor d rea a este enchufe
I-8 Conmutador de modo

I-10 Coperchio vano batterie svitarlo e toglierlo per insere le batterie
I-11 Adattatore A.C. --- -- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- —

---

    - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2
    - 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
    - 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5
    -  ·

D.C.

Iapakokovtheta touc youc tou wopou

Temperatures i bornevareelset

Phone : from Vienna 06010 1890

All other locations: 0660 6201

PORTUGAL

Phone:[phone]

ESPAN

Phone: [phone]

SVERIGE

Phone:[phone]

SCHWEIZ/SUISSE/SVIZZERA

Tel.:[phone]

UK

Phone:[phone]

SBC SC367/86U & SBC SC367/87U
R&TTE Directive 1999/5/EC

BE √	DK √	GR √	ES	FR √
IRE	IT √	LU √	NL √	AT √
PT √	FI √	SE	UK	NO √
DE √	CH √

SBC SC367/05U
R&TTE Directive 1999/5/EC

BE	DK	GR	ES	FR
IRE✔	IT	LU	NL	AT
PT	FI	SE	UK✔	NO
DE	CH

SBC SC367/13U
R&TTE Directive 1999/5/EC

BE	DK	GR	ES	FR
IRE	IT	LU	NL	AT
PT	FI	SE √	UK	NO
DE	CH

SBC SC367/16U
R&TTE Directive 1999/5/EC

BE	DK	GR	ES √	FR
IRE	IT	LU	NL	AT
PT	FI	SE	UK	NO
DE	CH