SRP620NC - Remote control PHILIPS - Free user manual and instructions

Product type	Universal remote control
Brand	Philips
Model	SRP620NC
Power supply	2 AA (LR6) batteries included
Dimensions (approx.)	20 × 5 × 2.5 cm
Weight (approx.)	120 g (with batteries)
TV compatibility	Philips TVs since 1985, RC6 mode for models after 1999
Device compatibility	DVD players/recorders, Philips VCRs
TV function keys	Standby, volume, channel, mute, menu, OK, arrows, EPG, PIP, etc.
DVD/VCR function keys	Play, pause, stop, forward, rewind, record, etc.
Switching mode	Press MODE to access secondary functions (PIP, etc.)
Teletext settings	OK+number combinations to adjust teletext (OK+8 or OK+6)
PIP settings	OK+2 to adjust the PIP function
Active Control/Smart settings	OK+4, OK+5, OK+8 as needed
Factory reset	OK+0 to reset all functions
Care and cleaning	Clean with a soft, dry cloth. Do not use abrasive products.
Safety	Keep away from heat sources and humidity. Remove batteries if not used for an extended period.
Spare parts and repairability	No user-serviceable parts. Contact Philips support.
General information	Manual available in several languages. Telephone support available.

Frequently Asked Questions - SRP620NC PHILIPS

How to insert the batteries?

Open the battery compartment cover on the back of the remote control and insert two AA (LR6) batteries, respecting the indicated polarity.

How to check if the remote control works with my TV?

Press basic keys like Volume or Channel. If the TV does not respond, follow the adjustment instructions in chapter 4 of the manual.

What to do if teletext does not work correctly?

Press and hold OK and 8 simultaneously for 5 seconds until the indicators flash twice.

How to control a Philips VCR or DVD player?

Press the MODE key twice to switch to DVD/VCR mode. The corresponding indicator lights up. Then use the appropriate keys (play, pause, etc.).

How to change the VCR configuration?

In DVD/VCR mode, press and hold OK + 5 for 5 seconds for VCRs, OK + 2 for DVD recorders, OK + 6 for a second VCR system, etc.

The PIP function does not work, what to do?

Make sure you are in TV mode, then press and hold OK + 2 for 5 seconds to adapt the remote control to your TV.

How to restore original TV functions?

Press and hold OK + 1 for 5 seconds. The indicators flash twice to confirm.

How to completely reset the remote control?

Press and hold OK + 0 for 5 seconds. The indicator flashes twice to indicate the reset.

What to do if my TV (after 1999) does not respond to any key?

Press and hold OK + 3 for 5 seconds to switch to RC6 code. Ensure the batteries are correctly inserted.

Where to find help if the remote control still does not work?

Consult the full manual or contact Philips support line. Have your TV and remote control references (SRP620) ready.

USER MANUAL SRP620NC PHILIPS

Instructions for use

English 4

Mode d'emploi

Français 10

Bedienungsanleitung

Deutsch 16

Gebruiksaanwijzing

Nederlands 22

Instructions for use

CONTENT

Introduction...... 4

Getting started.... 4

Inserting the batteries.... 4

Testing the remote control.... 4

Shift Mode 4

DVD/VCR Mode 5

Keys and functions 5-6

Adjustments to your remote control.... 6-7

Selecting the right VCR or DVD functions 7-8

Extra possibilities....9

Need help? 9

INTRODUCTION

You just made a great choice by buying this Philips remote control! It can replace any Philips TV remote control manufactured since 1985.

If you also have a Philips DVD player/recorder, VCR or Combi TV with build in VCR or DVD player,

you can operate these devices with the SRP620 as well.

GETTING STARTED

ADVICE

Carefully read the complete procedure before starting!

Inserting the batteries

The SRP620 needs two batteries of the type AA/R06 that are included in the packaging. Open the battery cover and place the batteries as indicated in the drawing.

Testing the remote control

The SRP620 is programmed to send out the most common functions used in Philips TVs. As the available functions vary over the different TV models, you might need to change some settings in the remote control to be able to control all TV functions.

First, test all the buttons on the remote and check whether the TV responds correctly to the commands of the SRP620.

NOTE

- If the TV does not respond correctly or not at all, go to chapter: 'Adjustments to your remote control'.

Shift Mode

To access some of the functions you have to use the SHIFT mode in combination with another key.

For turning on PIP mode e.g., press the Mode key once.

The Shift light starts blinking now. Press the Red button with the PIP symbol.

The PIP mode will now be activated and the Shift light stops blinking.

For a description of the functions on the SRP620, please go to the next chapter.

Instructions for use

DVD/VCR Mode

To control a Philips DVD or VCR you have to press the Mode key twice briefly.

The DVD/VCR light will turn on, indicating that you have selected the DVD/VCR mode.

Pressing the Mode key again, turns the remote back into TV mode.

KEYS AND FUNCTIONS

		TV function	Shift TV function	DVD/VCR function
1	Standby	Standby, power on/off		Standby, power on/off
2	Mode
3	EPG	EPG, guide	EPG record	Rewind
4	White	White		Fast Forward
5	Red	Red	PIP dual screen	Record
6	Green	Green	PIP Swap	Pause
7	Yellow	Yellow	Freeze	Stop
8	Blue	Blue	PIP shift	Play
9	Sleep	Sleeptimer	Clock	Angle
10	OSD	Info, OSD	Main freeze	OSD
11	Wide screen
		Screen, 16:9	TV select	Zoom
12	Surround
		Incredible surround	Subtitle	Surround sound, showview
13	I-II	Smart sound, sound preferences	I-II Mono/stereo	Audio, I-II
14	PP	Active control	Personal preference	Disc manager/disc menu
15	CC	Smart picture	Closed captioning	Title/chapter, Index
16	Menu	Menu	Search	Menu
17	OK
18	Cursor up
		Cursor up	Brightness +	Cursor up
19	Cursor left
		Cursor left	Color -	Cursor left
20	Cursor right
		Cursor right	Color +	Cursor right
21	Cursor down
		Cursor down	Brightness -	Cursor down
22	Volume +
		Volume up	Balance Right	Volume up TV
23	Program +
		Program up		Next
24	Volume -
		Volume down	Balance Left	Volume down TV
25	Mute	Mute	Channel/Program	Mute sound TV
26	Program -
		Program down		Previous

Instructions for use
English

			TV function	Shift TV function	DVD/VCR function
27	TWOLED	Smiley	Smiley	Conceal/reveal	Short play/long play, Options
28	LITRANS	Frownie	Frowney	Text enlarge	Tuner
29	INNOGIB	Text	Text on/off	Text cancel	Select/VPS
30	-	txt mix	Text hold	Text mix	Clear
31	LITRANS *	3	1-9	+ 1: Radio+ 2: TV+ 3: HD+ 4: PC	1-9
32	LITRANS	Ext	External input 1	External input 2
33	LITRANS	0	0		0
34	LITRANS	P<P/--/--	Previous program	Double digitprogram selection

For installing TV channels on older Philips TVs D-, press and simultaneously. For leaving the teletext menu or the installation menu on older Philips TVs d-, press and simultaneously.

ADJUSTMENTS TO YOUR REMOTE CONTROL (TV)

This is only necessary if your TV does not respond at all or if the TV does not respond correctly to some of the keys on the SRP620. With a simple procedure you can adapt the SRP620 to your TV.

Teletext buttons are not working properly

Some TVs work with different Teletext commands.

Solution:

• Make sure the remote control is in TV mode (both Mode lights must be out).
• Press and hold the OK button and digit 8 simultaneously for 5 seconds till the mode lights blink twice.
• If Teletext still doesn't work, go to the next paragraph.

Teletext buttons do not work at all

Some Matchline TVs work with different Teletext commands.

Solution:

• Make sure the remote control is in TV mode (both Mode lights must be out).
• Press and hold the OK button and digit 6 simultaneously for 5 seconds till the mode lights blink twice.

Picture in Picture (PIP) is not working

Some Philips TVs work with different PIP commands.

Solution:

• Make sure the remote control is in TV mode (both Mode lights must be out).
• Press and hold the OK button and digit 2 simultaneously for 5 seconds till the mode lights blink twice.

Instructions for use

TV is not responding to any key

If your TV is purchased after 1999, it is possible that it uses the new RC6 remote control code.

Solution:

• Make sure the batteries are inserted as indicated in chapter 1.
• Make sure the remote control is in TV mode (both Mode lights must be out).
• Press and hold the OK button and digit 3 simultaneously for 5 seconds till the mode lights blink twice.

The Active control, smart sound and smart picture keys are not working

In some TV sets are different commands used.

Solution:

• Make sure the remote control is in TV mode (both Mode lights must be out).
• Press and hold the OK button and digit 5 simultaneously for 5 seconds till the mode lights blink twice.

The Active control key is not working

In some TV sets a different command is used for this function.

Solution:

• Make sure the remote control is in TV mode (both Mode lights must be out).
• Press and hold the OK button and digit 4 simultaneously for 5 seconds till the mode lights blink twice.

The Smart sound and Smart picture keys are not working

In some TV sets are different commands used for these functions

Solution:

• Make sure the remote control is in TV mode (both Mode lights must be out).
• Press and hold the OK button and digit 8 simultaneously for 5 seconds till the mode lights blink twice.

SELECTING THE RIGHT VCR OR DVD FUNCTIONS

If you select the DVD/VCR function, the remote is set for DVD-player functions. Please read the steps below if you want to select VCR or DVD-recorder functions.

Setup VCR functions

If you want to operate a Philips videocassette recorder do the following:

1 Select the DVD/VCR mode by pressing once on the mode key at the side.

- The DVD/VCR mode light should light up.

2 Press and hold 'OK' and digit 5 simultaneously for 5 seconds, until the mode lights blink twice.

- The DVD/VCR mode is now programmed for Philips VCRs.

NOTE

- You cannot operate the DVD functions anymore.

Instructions for use

English

Setup DVD-R functions

If you want to operate a Philips DVD-recorder do the following:

1 Select the DVD/VCR mode by pressing once on the mode key at the side.

- The DVD/VCR mode light should light up.

2 Press and hold 'OK' and digit 2 simultaneously for 5 seconds, until the mode lights blink twice.

- The DVD/VCR mode is now programmed for Philips DVD recorders.

Setup different RC systems for DVD/VCR

In case you have more than one VCR or DVD from Philips, you might have chosen the option to change the RC system of the VCR or DVD. If the DVD, DVD-R or VCR functions as described above don't work, you can try the following:

For VCR system 2:

1 Select the DVD/VCR mode by pressing once on the mode key at the side. - The DVD/VCR mode light should light up.

2 Press and hold 'OK' and digit 6 simultaneously for 5 seconds, until the mode lights blink twice. - The DVD/VCR mode is now programmed for Philips VCR system 2.

For DVD system 2:

1 Select the DVD/VCR mode by pressing once on the mode key at the side. - The DVD/VCR mode light should light up.

2 Press and hold 'OK' and digit 3 simultaneously for 5 seconds, until the mode lights blink twice. - The DVD/VCR mode is now programmed for Philips DVD system 2.

For DVD-R system 2:

1 Select the DVD/VCR mode by pressing once on the mode key at the side. - The DVD/VCR mode light should light up.

2 Press and hold 'OK' and digit 4 simultaneously for 5 seconds, until the mode lights blink twice. - The DVD/VCR mode is now programmed for Philips DVD-R system 2.

Instructions for use

EXTRA POSSIBILITIES

Restoring the original TV functions

If you want to restore the SRP620 to its original TV functions, do the following:

- Press and hold the OK button and digit 1 simultaneously for 5 seconds till the mode lights blink twice.

- The remote is now restored in the default TV functions.

Restoring the original functions on the entire remote control

To revert the SRP620 back to the factory default settings, do the following:

- Press 'OK' and '0' simultaneously for 5 seconds.

- The mode light will blink twice to confirm a successful reset.

NEED HELP?

If you have any questions about the SRP620, call our special helpline, You will find the telephone number on page 2 of this manual.

Read this manual carefully before you make a call.

You can solve most of the problems yourself.

If you cannot find any answers to your problems, write down the details of your TV, DVD or VCR. This will help our operators to assist you better and more quickly.

Look up the model numbers of your device in the instruction manual or at the back of your device. When you call our helpline, make sure the device is at hand so that our operators can help you determine whether your remote control is working properly.

The model number of your Philips remote control is SRP620

Date of purchase: ..... /..... /..... (day/month/year)

Mode d'emploi

TABLE DES MATIERES

Introduction.... 10

Pour démarrer 10

Insertion des piles.... 10

NÄPPÄIMET JA TOIMINNOT