TYWK65PV7 - TV PANASONIC - Free user manual and instructions

USER MANUAL TYWK65PV7 PANASONIC

（左右）7 English Precautions with regard to setting up WARNING Installation work should only be carried out by a qualified technician.

• If the bracket is installed incorrectly, the display may fall down and personal injury may result. Make sure that all safety factors regarding strength of installation are observed.

• If the installation strength is insufficient, the display may fall down and personal injury may result. Do not install in places which are unable to bear loads.

• If the strength of the installation surface is insufficient, the display may fall down and personal injury may result. CAUTION Do not install in places which are subject to humidity, dust, oil fumes, water vapour or excessive heat.

• These can have adverse effects on Plasma Display operation, and fire or electric shocks may result. Do not install the Plasma Display face up, sideways or upside down.

• Doing so may cause heat to build up inside the display, and fire may result. Two people are required to install and remove the display.

• If two people are not present, the display may be dropped, and personal injury may result. Maintain a space of at least 10 cm

at the top, bottom and sides of the display, and at least 7.5 cm (2

/64 inches) at the rear of the display.

• The display has ventilation outlet holes on the rear, and ventilation inlet holes on the bottom, sides and rear. Covering these may result in a fire.8 English Components Points to note during installation

The wall-hanging bracket is for use in installing the Plasma Display to a vertical wall for viewing purposes. Do not use it for any type of installation other than vertical wall installation.

In order to ensure correct, problem-free operation of the Plasma Display, do not install the Display in any of the following places.

• Places which are next to sprinklers or sensors

• Places which are subject to vibration or shocks

• Places which are close to high-voltage wires or electric motors

• Places in direct contact with air from heaters

When installing this wall-hanging bracket unit, use a fixing method appropriate to the type of wall.

Use an M6 bolt (sold separately) appropriate for the type of wall material (wood, steel frame, concrete, etc.) the bracket is to be mounted on.

Keep retention screws and power cord away from any metallic parts or structures within the wall.

Insert the power cord plug for the Plasma Display into a wall outlet which is close and easily accessible.

• Provide adequate ventilation so that the temperature around the display does not rise above 40°C (104 °F). If there is insufficient movement of the air inside display, heat may build up inside the display, and fire may result. Wall-hanging bracket unit p. 1
• Allen key (accessory) p. 1
• Cover p. 2
• Fixing screw (M5-133) Insulating spacer p. 2

Pan head bolt with hex socket (M8-30) .........49 English Installation procedure The wall-hanging bracket weighs approximately 8.3 kg (18.3 lbs.) and the Plasma Display unit weightsapproximately 81.5 kg (179.6 lbs.). (85.9 kg (189.4 lbs.) when speakers are fitted.).While referring to the wall-hanging bracket installation dimensions in the diagram below, check the strength ofthe wall in six installation locations, and add reinforcing if any of these locations are not strong enough.

1. Check the strength of the installation location.

• Install the Wall-hanging bracket so that the arrow shown on the bracket is pointing upwards.

• If it is necessary to embed bolts or nuts beforehand because the wall is made from concrete, use the bracket itself to determine the correct installation hole positions, or use the dimension diagram to calculate the holepositions. Then embed the M6 bolts or nuts into the holes. Furthermore, when embedding the bolts, allow thebolts to protrude from the wall by 10 mm ( /32 inches) to 15 mm ( /32 inches).

2. Install the wall-hanging bracket to the wall.

Installation procedure 1. First screw a bolt into the center-tophole.2. Use a level gauge to correct thealignment of the wall-hanging bracket,and then screw bolts into theremaining five holes.3. Provisionally tighten the fixing screws.If the screws are inserted more than 5 mm (

• The wall-hanging bracket hasinstallation holes provided in 14locations.if the wall material will not allowsufficient strength to be obtained fromusing six installation holes, use some ofthe spare holes.However, depending on theconstruction material used at the placeof installation, cracks may develop ifthe screws are inserted too close toeach other.Caution• Use commercially-available M6 boltswhich suit the wall materials forinstallation to the wall.Caution• The marks indicate the centerline of thePlasma Display.Wall installation holes (6 locations)Units: mm (inches) Horizontal installation Vertical installation Marks (H)Marks (V)Marks (V)Fixing screw(M5-133)Fixing screw(M5-133)Fixing screw(M5-133)Note10 English
• Do not lift the display too high, otherwise it may become unhooked. Note

3. Prepare the Plasma Display.

4. Install the display to the wall-hanging bracket.

Installation procedure Push the upper insulating spacers onthe display into the notches at the topof the wall-hanging bracket until theyare hooked in, and then lower thedisplay into place.While lifting the display slightly, insertthe lower insulating spacers on thedisplay into the lower horizontalhanging holes in the wall-hangingbracket, and then lower the display. Installation procedure

• Place the display face down on top of a cloth which is clean and free from other foreign particles, and then carry out the procedure above. Note Caution Pan head bolt wih hex socketToothed pan washerInsulating spacerAllen key 1. Use the accessory tool (Allen key) to installthe four accessory pan head bolts with hexsocket, toothed pan washers and insulatingspacers into the holes as shown in theillustration.2. Install the covers.• Install the two covers over the holes on theunder side of the Plasma Display. Attach the insulating spacers to the display. Notches (For vertical installation)Notches (For horizontal installation)Lower (For verticalinstallation)Lower(For horizontalinstallation)Insulating spacerCover11 English
• Tighten the fixing screws at left and right.
• Be sure to tighten the left and right fixing screws to prevent the display from detaching from the wall-hanging bracket. Caution Removing the display 1. Remove the two fixing screws which arescrewed into the wall-hanging bracket.2. While lifting up the bottom of the display. Pull it forward to detach the insulatingspacers at the bottom.Then lift up the display.

5. Secure the Wall-hanging bracket.