ToptelTV 100 - Remote control CME - Free user manual and instructions

Frequently Asked Questions - ToptelTV 100 CME

USER MANUAL ToptelTV 100 CME

The CME replacement remote control was designed as a TV control. Thanks to its large database and numerous functions it is ideal for replacing any lost, defective or broken remote control.

Keep this booklet in case you ever need to consult it in the future.

For anyone with internet, via the website www.cme.it

it is even easier and quicker to programme the remote control and discover all its potential thanks to the on-line guide.

USING THE KEYS AND FUNCTIONS

Read these instructions carefully before programming your remote control!

	Light indicator
	TV ON/OFF key
	Teletext keys
1-2-3-4-5-6 7-8-9-0-1--	Number keys
AV	To select an external input terminal
	MUTE key turns the volume on and off
+P-	To select the next (P+) or previous (P-) channel or programme
+▲-	Control the volume using +/−
	To move around within the MENU or to control the BRIGHTNESS/CLOUR
OK	Confirm key
	Key with additional TV functions
	To access the MENU
green red blue yellow	Fastext functions or to select submenus by means of the colours

PREPARE FOR USE

Read these instructions carefully before programming your remote control!

Before programming and using the remote control, fit the batteries.

The remote control requires 2 new AAA/LR03 batteries.

• Change the batteries if the light indicator starts to flash during use. The batteries are low.
• When you remove the batteries, fit the new ones within 5 minutes or you may have to reprogramme your remote control.
• Make a note of the code for your TV on the adhesive label inside the battery cover in case you have to reprogramme your remote control.

HOW TO PROGRAMME THE REMOTE CONTROL

The quickest and easiest way to programme the remote control is by consulting the website www.cme.it.

1. Switch on the TV.
2. Look for the brand of the television you want to programme in the code list and make a note of the corresponding code alongside (e.g. PHILIPS 0025).
3. Hold down the MUTE and ON/OFF keys together for 3 seconds until the light indicator starts to flash indicating that the remote control is being programmed.
4. Release the keys. Within 12 seconds, enter the brand code previously identified (e.g. 0025). The light indicator flashes more quickly to indicate that the remote control is ready for the search.
5. Point the remote control towards the TV. Press and slowly release the ON/OFF key several times, stopping when the TV goes off.
6. When the TV goes off, press the OK key to confirm. Three flashes indicate that the operation has been completed correctly.

PHILIPS 0025

5 SEC.

ADDITIONAL CHECK

Check that some of the other keys, corresponding to those on your original remote control, work correctly. If the commands function incorrectly or erratically, you have probably entered a code for a similar remote control but not the right one. In this case, repeat the search procedure starting from point 3, entering the code previously used (e.g. 0025).

To display and make a note of the code memorized by means of the search, follow the instructions described in the paragraph CURRENT CODE DISPLAY.

NB: THE LIGHT INDICATOR STOPS FLASHING

The remote control exits programming mode and the light indicator stops flashing:

• if no keys are pressed for 14 seconds
• if an invalid brand code is entered
• if the code search list is completed. In this case, consult the website www.cme.it

This operation can take up to 20 minutes and should be carried out if you have not succeeded in programming the remote control by means of the method described above.

The quickest and easiest way to programme the remote control is by consulting the website www.cme.it.

1. Switch on the TV.
2. Hold down the MUTE and ON/OFF keys together for 5 seconds until the light indicator starts to flash indicating that the remote control is being programmed.
3. Release the keys. Within 12 seconds, enter the code 0000. The light indicator flashes more quickly to indicate that the remote control is ready for the search.
4. Point the remote control towards the TV. Press and slowly release the ON/OFF key several times, stopping when the TV goes off.
5. When the TV goes off, press the OK key to confirm. Three flashes indicate that the operation has been completed correctly.

ADDITIONAL CHECK

Check that some of the other keys, corresponding to those on your original remote control, work correctly. If the commands function incorrectly or erratically, you have probably entered a code for a similar remote control but not the right one. In this case, repeat the search procedure starting from point 2.

To display and make a note of the code memorized by means of the search, follow the instructions described in the paragraph CURRENT CODE DISPLAY.

NB: THE LIGHT INDICATOR STOPS FLASHING.

The remote control exits programming mode and the light indicator stops flashing:

• if no keys are pressed for 14 seconds
• if the code search list is completed. In this case, consult the website www.cme.it

CURRENT CODE DISPLAY

To find out the code of your remote control, follow this procedure:

1. Hold down the MUTE and ON/OFF keys together for 5 seconds until the light indicator starts to flash.
2. When the MUTE and ON/OFF keys are released, press and release the 1-/- key within 8 seconds.
3. After a pause of several seconds, the indicator light produces four series of flashes with a space between them, corresponding to the code you are looking for. Count the number of flashes; each series of flashes corresponds to one figure in the code. 10 flashes correspond to 0.
4. Note the code on the adhesive label inside the battery cover in case you have to reprogramme the remote control subsequently.

5 SEC.

1

0 3

0

6

Code obtained = 1306

NB: this operation cannot be interrupted and the remote control cannot therefore be used until the end of the four series of flashes.

ENTERING THE CODE

If you know the exact code with which to programme the remote control, enter it as follows:

1. Hold down the MUTE and ON/OFF keys together for 5 seconds until the light indicator starts to flash.
2. Release the keys and enter the code (eg: TV 1308, Three flashes indicate that the operation has been completed correctly.

5 SEC.

：

+

HOW TO USE THE ADDITIONAL COMMANDS WHICH DO NOT APPEAR ON THE KEYPAD

Although not indicated on the keypad, some keys can be used for additional commands.

Find them on your remote control by pressing the keys one by one and discovering the commands that interest you.

In particular, the additional functions most frequently used, such as NORMALIZATION, COLOUR and BRIGHTNESS, can be found on the following keys:

Normalization:

Brightness (+) : or green

Brightness (-): or red

Colour (+) :or blue

Colour (-): or yell

For the functions used less frequently, look for the additional commands on the site www.cme.it. As well as easily finding the code to programme your remote control, consulting the on-line guide will help you to find which keys on the remote control correspond to the additional commands.

PROBLEM

The TV does not respond and the light indicator does not light up when a key is pressed.

SOLUTION

Try some of the other frequently-used keys. If the problem persists, check that the batteries are fitted correctly. If necessary, replace them with 2 new 1.5 V AAA/LR03 batteries.

The TV does not respond but the light indicator does light up.

Check that the batteries are new and that the remote control is pointing at the TV without any obstacles in the way. If required, reset the remote control code, following the programming procedure.

The light indicator flashes when a key is held down but the TV does not respond.

The batteries are low. Change them.

The remote control commands are not all working correcting.

You may have used the wrong code. Reset the remote control code, following the programming procedure.

The code for your appliance brand is not listed.

To find the code with which to programme your remote control consult the on-line guide at www.cme.it.

INFO-LINE

If you have any queries about your remote control:

• read this Instruction Booklet carefully - you will find an answer to most of your questions
• consult our website www.cme.it where you will find the answers you need easily and quickly.

You can also write to customer service at [e-mail]. To facilitate and speed up customer service operations, please provide the following essential information on your appliances:

Model of CME remote control: (see body of remote control)

Make of appliance Type Model Mod. original remote control Brand code
e.g.: THOMSON TV 25DU78M RCT 4000 1007

WARRANTY: 2 years

The warranty ceases to be valid if the product is tampered with or used incorrectly.

Dealer's stamp

Purchase date / /

The symbol of the crossed trash can shown on the remote control indicates that once the product has reached the end of its working life it should be disposed of separately from other waste. The user should, therefore, take the remote control to a specialised collection centre for electronic and electrical waste, or hand it over to the dealer when purchasing a new similar remote control, on a one to one basis. Correct separated collection for subsequent recycling, processing and environmentally compatible disposal contributes in preventing possible negative effects on the environment and on health and favours the recycling of the materials used in producing the remote control. Improper disposal of the product by the user leads to application of the penalties as per legislative decree no. 22/1997 (article 50 and following of decree no. 22/1997).