VL 3602 - Fan CLATRONIC - Free user manual and instructions

USER MANUAL VL 3602 CLATRONIC

White CM IRONC air conditioner fan with four blades and mesh grille (no text or symbols visible)

Overview of the Components	page	3
Instruction Manual	page	25
Technical Data	page	28
Disposal	page	28

JEZYK POLSKI

Spis tres'ci

Technical diagram of a mechanical device with numbered parts for identification

Bedienungsanleitung

Thank you for choosing our product. We hope you enjoy using the appliance.

Symbols in these Instructions for Use

Important information for your safety is specially marked. It is essential to comply with these instructions in order to avoid accidents and prevent damage to the machine:

WARNING:

This warns you of dangers to your health and indicates possible injury risks.

CAUTION:

This refers to possible hazards to the machine or other objects.

NOTE: This highlights tips and information.

General Notes

Read the operating instructions carefully before putting the appliance into operation and keep the instructions including the warranty, the receipt and, if possible, the box with the internal packing. If you give this device to other people, please also pass on the operating instructions.

• The appliance is designed exclusively for private use and for the envisaged purpose. This appliance is not fit for commercial use.
• Do not use it outdoors. Keep it away from sources of heat, direct sunlight, humidity (never dip it into any liquid) and sharp edges. Do not use the appliance with wet hands. If the appliance is humid or wet, unplug it immediately.
• When cleaning or putting it away, switch off the appliance and always pull out the plug from the socket (pull the plug itself, not the lead) if the appliance is not being used and remove the attached accessories.
• Do not operate the machine without supervision. If you leave the room you should always turn the device off. Remove the plug from the socket.
• The device and the mains lead have to be checked regularly for signs of damage. If damage is found the device must not be used.
• Use only original spare parts.
• In order to ensure your children's safety, please keep all packaging (plastic bags, boxes, polystyrene etc.) out of their reach.

WARNING!

Do not allow small children to play with the foil. There is a danger of suffocation!

Special safety instructions

• Never stick fingers or other objects through the protection grid.
• Watch out for long hair! It can be caught in the fan owing to the air turbulence!
• Use the appliance only with the protection grids on!
• If you need to remove the fan guard, first switch off the appliance and disconnect the mains plug.
• Select a stable base to avoid the tipping of the fan during use!
• Do not place the device immediately next to stoves or other sources of heat.

• Do not try to repair the appliance on your own. Always contact an authorized technician. To avoid the exposure to danger, always have a faulty cable be replaced only by the manufacturer, by our customer service or by a qualified person and with a cable of the same type.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  • Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children without supervision.
• Do not immerse the device into water for cleaning. Please follow the instructions as stipulated in the chapter “Cleaning”.

Overview of the Components

1 Hook
2 Propeller
3 Motor shaft
4 Motor
5 Adjustment knob for oscillation
6 Switch housing
7 Operating mode switch
8 Base
9 Rear protection grid
10 Fastening nut
11 Attachment ring for rear protection grid
12 Fastening screw
13 Fastening screw
14 Front protection grid

Not shown: crosshead screw

Unpacking the Device

1. Remove the device from its packaging.
2. Remove all of the packaging material such as foils, filling material, cable holders and cardboard packaging.
3. Check the scope of delivery.
4. Check the appliance for any transport damage to prevent a hazard.

i NOTE:

There may still be dust or production residues on the surface of the device. We recommend that you quickly wipe off the housing with a damp cloth.

Assembly instructions

The device must be completely assembled before initial operation!

i NOTE:

• You will need a Phillips screwdriver of medium size for the assembly.
• Screws not included with the accessories are pre-fitted on the individual parts.

• Also observe the "Overview of the Components" on page 3.

• Place the stand tube (6) in the base (8). Attach it on the bottom until it is snapped.

• Unscrew the mounting ring (11) in an anticlockwise direction. Keep it ready to hand.
• Position the rear protection grid (9) in place in accordance with the recesses.

i NOTE:

Please ensure that the carrying handle is facing upwards.

1. Turn the attachment ring (11) for the rear protection grid (9) slightly in a clockwise direction.
2. Attach the propeller. Note the position of the guide pin on the motor shaft.
3. Tighten the attachment screw (12) for the propeller in an anticlockwise direction.
4. Remove the preassembled fastening screw (13) and nut (10) from the wire mesh guard. Keep it ready to hand.
5. Hang the front protective guard (14) to the rear protective guard with the hook (1).

i NOTE:

Ensure that the holes for the attachment screw in the front and rear protective grille are aligned one above the other.

1. Secure the wire mesh guard with the fastening screw (13) and nut (10).

2. Close the attachment hooks.

Position

The ideal position is a non-slip, flat surface.

Putting into Service

Electrical Connection

• Before inserting the plug into the socket. Make sure that the mains voltage to be used matches that of the device. You can find this information on the nameplate.
• Connect the device to a duly installed protective contact socket.

Use

Basic Settings

Set the blower inclination angle before starting the device.

- Hold the motor housing with both hands and tilt it carefully to the desired position. It clicks audibly into place.

CAUTION:

The tilting angle is about 30 degrees.

Operation

To select the speed, use the pressure switch on the front:

0 off
1 slow
2 medium
3 fast

To shut off the device, select the position 0.

Fan setting

You have two options:

- Stationary

1. Shut off the device.
2. Pull the control knob upwards.
3. Use the carrying handle to place the device into the desired position.

- Oscillating

1. Shut off the device.
2. Press the control knob.

NOTE:

The device rotates automatically in the range of about 90 degrees.

1. To turn off the function, shut off the device and pull the control knob upwards.

Cleaning

WARNING:

• Always remove the mains plug before cleaning the device.
- If you need to remove the safety guard: Always switch the device off and remove the mains plug.
- Under no circumstances should you immerse the device in water for cleaning purposes. Otherwise this might result in an electric shock or fire.

CAUTION:

• Do not use a wire brush or any abrasive items.

• Do not use any acidic or abrasive detergents.

• Clean the outside of the device with a dry cloth without any additives.

• If the device is very dirty wet a cloth with water and then wipe the device dry once you have finished.

Maintenance and storage

• Clean the appliance as described.
  • We recommend that the appliance is kept in its original packaging if you do not intend to use it for long periods.
  • Always store the appliance out of the reach of children, in a well-ventilated and dry place. Noise development

Noise development

The workplace-related emission value is less than 70 dB(A).

Technical Data

Model: VL 3602

Power supply: 220-240 V\~, 50/60 Hz

Power consumption: 40 W

Protection class: ____

Net weight: approx. 1.60 kg

The right to make technical and design modifications in the course of continuous product development remains reserved.

This device has been tested according to all relevant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and has been constructed in accordance with the latest safety regulations.

Disposal

Meaning of the "Dustbin" Symbol

Protect our environment: do not dispose of electrical equipment in the domestic waste.

Please return any electrical equipment that you will no longer use to the collection points provided for their disposal.

This helps avoid the potential effects of incorrect disposal on the environment and human health.

This will contribute to the recycling and other forms of reutilisation of electrical and electronic equipment.

Information concerning where the equipment can be disposed of can be obtained from your local authority.

Instrukcja obsługi

CTC Clatronic Sp. z o.o

Ul. Brzeska 1

45-960 Opole

Usuwanie