AT262 - Blender KENWOOD - Free user manual and instructions

USER MANUAL AT262 KENWOOD

Use the liquidiser for soups, drinks, pâtés, mayonnaise, breadcrumbs, biscuit crumbs, chopping nuts and crushing ice. before using your Kenwood attachment

Read these instructions carefully and retain for future reference.

Remove all packaging and any labels. safety

Allow all liquids to cool to room temperature before placing them in the liquidiser.

Only use the jug with the blade unit supplied.

Never attempt to fit the blade unit to the machine without the jug fitted.

Always unplug the machine before putting your hands or utensils in the jug.

Switch off and unplug: before fitting or removing parts after use before cleaning.

Never use a damaged machine. Get it checked or repaired: see ‘service’.

When removing the liquidiser from the power unit wait until the blades have completely stopped.

Only operate the liquidiser with the lid in place.

Never leave the appliance unattended when it is operating.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

Only use the appliance for its intended domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions. important The skirt on the bottom of the jug is fitted during manufacture and no attempt should be made to remove it.

The liquidiser will not operate if the medium speed outlet cover is not correctly fitted.

Never run the liquidiser for longer than one minute - it will overheat. Switch off as soon as you have the right consistency.

Don’t put dry ingredients into the liquidiser before switching on. Cut them into cubes, then remove the filler cap and drop the cubes through the hole in the lid whilst the machine is running.

Acrylic jug (AT262): don’t process spices such as cloves, dill and cumin seeds - they damage the acrylic.

Don’t use the liquidiser as a storage container. Keep it empty before and after use.

Never crush ice on its own, always add a little water.

Never blend more than 1.5 litres (2 pints 12fl oz) - less for frothy liquids like milk shakes.

Smoothie recipes - never blend frozen ingredients that have formed a solid mass during freezing, break it up before adding to the liquidiser. before using for the first time Wash the parts: see ‘cleaning’. English 2key filler cap lid

sealing ring blade unit to use your liquidiser 1Ensure the sealing ring is correctly fitted on the blade unit. 2 Hold the underside of the blade unit and insert the blades into the base of the liquidiser. Twist to lock the assembly firmly in place. 3 Put your ingredients into the jug. 4 Fit the lid to the jug and twist clockwise into place, making sure that the tab on the lid slots into the groove in the handle. When correctly fitted the markings should align .

The liquidiser will not operate if the lid is not correctly fitted. 5 Place the filler cap into the lid. 6 Remove the high speed outlet cover by turning anti clockwise and lifting off 7 Place the liquidiser over the outlet, handle towards the back and turn clockwise to lock firmly into place

The liquidiser will not operate if incorrectly fitted to the mixer. 8 Switch to maximum speed. 9 Once the desired consistency has been achieved, switch off and unplug. 10 Remove the liquidiser. hints

To prevent leaks make sure the base is locked firmly into the jug.

When making mayonnaise, put all the ingredients, except the oil, into the liquidiser. Then, with the machine running, remove the filler cap and add the oil slowly and evenly.

Thick mixtures, eg pâté, dips: use low to medium speed, scraping down when necessary. If it’s difficult to process, add more liquid. Alternatively use the pulse setting to get the ingredients moving over the blades. cleaning

Always dismantle before cleaning.

Empty the jug before unlocking the base. blade unit 1 Remove and wash the sealing ring. 2Brush the blades clean under the tap. Keep the underneath of the unit dry. 3 Leave to dry. other parts Wash by hand in hot, soapy water. Alternatively the filler cap and lid, can be washed in your dishwasher. service and customer care

If the cord is damaged it must, for safety reasons, be replaced by KENWOOD or an authorised KENWOOD repairer.

If you need help with:

servicing or repairs call Kenwood Customer Care on 023 9239 2333. Have your model number ready - it is located on the underside of your appliance.

spares and attachments call 0870 2413653. other countries

Contact the shop where you bought your appliance.

PRODUKTET I SAMSVAR MED