Barista EA9010 - Machine à café KRUPS - Free user manual and instructions

USER MANUAL Barista EA9010 KRUPS

WELCOME Dear Customer,

Congratulations! You are now the proud owner of an Espresso Automatic Series EA9000. With

your machine, you can prepare a wide range of drinks; espressos, coffees or milk-based drinks,

entirely automatically. It is designed so that you can enjoy the same quality at home as in a

restaurant, whatever the time of the day and throughout the week. You will appreciate both the

quality of the result in your cup and its superior ease-of-use.

Thanks to its Compact Thermoblock System with built-in brewing chamber, its 15 bar pump, and

because it can use either coffee beans freshly ground just before the coffee is made or ground

coffee fed via a funnel, your machine will give you ristrettos, espressos and coffees hot from the

first cup with maximum aroma and a fine creamy golden-brown top.

With its exclusive and patented system for preparing milk-based drinks automatically, you can easily

make delicious cappuccinos and caffe lattes, without compromise: hot, with the “three layer effect”

and thick, creamy froth. Its automatic steam nozzle rinsing and cleaning programmes guarantee

hassle-free hygiene for long-lasting performance, cup after cup.

With the hot water function, you can prepare teas and other drinks instantaneously.

You can also personalise all of these drinks using the “Favourites” menu. You can set the volume,

proportions, intensity and temperature of your drinks.

The colour touch-screen makes navigation ergonomic and comfortable. It will guide you through

each step, from preparing your drink to servicing your machine.

We wish you many years of enjoyment with your Krups machine.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:41 Page4ENGLISH A FEW EXPERT TIPS Here are a few tips for achieving the best results from your machine:

n The quality of your water significantly influences the quality of the flavours. Limescale and

chlorine can alter the taste of your coffee. We recommend that you use the Claris Aqua

Filter System cartridge or low mineral-content water to preserve all of the flavours of your

n When preparing ristretto, espresso and coffee recipes, we recommend that you use

tulip-shaped porcelain cups, preheated beforehand (by running them under hot water, for

instance), and whose size is appropriate for the quantity you want to make. For your

cappuccino, caffe latte and hot milk recipes, we recommend that you use thick glass cups,

for an appealing, precise and gourmet presentation.

n Roasted coffee beans can lose their flavour if they are not protected. We recommended

that you use the amount of beans required for your consumption for the next 4-5 days. As

the machine automatically detects when there are no beans, you can be certain that you

will always have sufficient beans for preparing your coffee drinks. Though the quality of coffee

beans is subjective and varied, we can nevertheless recommend that you use arabica rather

than robusta. After a few trials, you will learn how to mix and roast the coffee beans

according to your tastes. Lastly, please remember that oily and caramelised coffee beans

must be avoided, as they can damage your machine.

n The quality and fineness of the grinding determine the strength of the flavours and the quality

of the crema. The finer the ground, the richer the crema. Moreover, it must be adapted to

the drink you want: fine for ristretto and espresso, coarser for coffee. For your comfort, the

machine carries out this operation automatically.

n Thanks to the ground coffee funnel and spoon, you can choose to serve your drink

differently. You can vary the flavours and strengths of your coffee as you wish. Ground coffee

should ideally be stored in the refrigerator in a hermetically sealed bag.

n You can use pasteurised or UHT, skimmed, semi-skimmed or whole milk, straight from the

refrigerator (7°C). Using special milks (microfiltered, raw, fermented, enriched, etc.) can

produce less satisfactory results especially regarding the quality of the froth. However, we

recommend that you use fresh, cold milk for pre-programmed recipes.

DEFRNLITEN IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:41 Page5KRUPS SERIE EA9000

The duration of this guarantee is 2 years.

Please check your guarantee card for more details on the guarantee conditions in your country.

This appliance is intended for domestic use only and is not suitable for commercial or professional use.

Any use other than domestic will void the guarantee.

The guarantee does not cover damage or faults resulting from improper use, repair by unauthorised

persons or non-observance of the instructions for use. The guarantee will become invalid if all of the

maintenance operations and instructions have not been followed, or if cleaning or descaling products

which do not comply with the original KRUPS specifications are used; if the Claris Aqua Filter System

water filter is not used in accordance with KRUPS instructions. Normal wear and tear of parts (grinding

disks, valves, seals) is exempted from the guarantee, as well as damages caused by foreign objects in

the coffee grinder (e.g. wood, stones, plastic parts etc.).

Caution: For the guarantee to be valid, this machine must be used only with Krups accessories.

ACCESSORIES (sold separately) Actual appearance may vary XS 9000

IMPORTANT INFORMATION ON THE APPLIANCE AND INSTRUCTIONS 6

1.1 Guide to the symbols used in the instructions 6

1.2 Safety guidelines 6

1.4 Products supplied with your machine 9

2.1 Description of the appliance 10

2.2 Presentation of the different symbols 12

2.3 Main operations of the appliance 12

INSTALLING THE APPLIANCE 16

4.1 Information on recipes 21

4.2 Preparing coffee-based drinks from coffee beans 22

4.3 Preparing coffee-based drinks from ground coffee 25

4.4 Preparing other drinks: hot milk with or without froth, and hot water 27

“FAVOURITES” MENU 30

8.2 Automatic cleaning programmes 41

IMPORTANT INFORMATION ON THE APPLIANCE AND INSTRUCTIONS

n In this manual you will find all of the important information concerning the preparation, use and

maintenance of your automatic coffee/espresso machine. Important safety guidelines are also included.

Read these instructions carefully before using your appliance for the first time and keep them for

reference: Krups may not be held responsible for any incorrect use.

1.1 Guide to the symbols used in the instructions

n Symbols and associated words used in these instructions.

1.2 Safety Instructions

n Do not immerse the appliance in water. Do not immerse the power cord or the mains plug in water or

any other liquid. Any contact of the conductive parts of the appliance with moisture or water may lead

to fatal injuries due to the presence of electricity! This appliance must only be used indoors in dry

n In the case of a change in the ambient temperature, from cold to hot, wait for a few hours before

using your machine so that it is not damaged by condensation. n Avoid leaving the appliance in direct sunlight, exposed to heat, cold, frost or humidity. n Do not place the appliance on a hot surface such as a hob or close to a naked flame, in order to

avoid any risks of fire or other damage! n Keep the appliance out of the reach of children. 1

SYMBOL ASSOCIATED WORD MEANING Danger

Warning against risks of serious or fatal injuries.

The lightning bolt symbol warns against electrical dangers.

Warning against risks of incorrect operation, damage

or destruction of the appliance.

General or important note on the operation of the appliance.

Important: These safety guidelines are intended to protect you and other persons, and the appliance.

They must therefore be respected.

n This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their safety.

n Children should be supervised to ensure that they do not play with the appliance.

n In case of ingestion of any of the products supplied with the machine, inform your physician and/or

the poison control centre immediately.

Electrical power supply

n Check that the supply voltage marked on the rating plate of the appliance is the same as that of

your electrical supply. Only connect the appliance to an earthed mains socket.

n Ensure that the mains socket is easily accessible so that the appliance can be unplugged easily,

for example in the event of any failure or a thunderstorm. For the safety of the appliance, unplug

it from the socket during thunderstorms. Do not pull on the power cord to unplug it from the

n Unplug it from the mains socket immediately if any operational failure occurs or if there is a problem

with brewing. Unplug the appliance when it is not to be used for a long period and when you are

n Do not use the appliance if the power cord or the appliance itself is damaged.

n If the power cord or the mains plug is damaged, they must only be replaced by an approved

KRUPS service centre.

n Do not let the power cord dangle over the edge of a table or a worktop. Do not leave the power

cord close to or in contact with the hot parts of the appliance.

n We do not recommend the use of extensions or multi-adapter plugs.

n Any incorrect connection invalidates the guarantee.

n Do not pour water into the coffee bean container and/or under the ground coffee funnel.

n Except for cleaning and descaling as described in the instructions for the appliance, all work on

the appliance must be carried out by a KRUPS approved service centre.

n For your safety, only use KRUPS approved accessories and consumables as they are perfectly

adapted to your appliance.

n Unplug the appliance when leaving the room or your home for prolonged periods.

n Never open the appliance, as there is a risk of fatal injury due to electricity! Any unauthorised

opening of the appliance invalidates the guarantee. Do not use your appliance if it is not working

correctly or if it has been damaged. In such cases, we recommend having the appliance checked

by a KRUPS approved service centre (see the list in the KRUPS Service handbook).

n For safety and approval (CE) reasons, any transformation or modification of the appliance carried

out by an individual is prohibited, as only tested appliances have been approved and the

manufacturer is absolved of all responsibility in the event of damage.

Danger: Failure to respect these guidelines may lead to fatal injuries due to electricity!

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:41 Page7KRUPS SERIE EA9000

n When producing steam for making cappuccino, hot milk or hot water, do not block the mechanism

that brings the steam nozzle forward, downward, upward or backward. In such cases, the

manufacturer is absolved of all responsibility in the event of damage to the appliance and the guarantee

n For your safety, while producing steam for making cappuccino, hot milk or hot water, do not place

your hand under the steam nozzle. n The steam nozzle can be hot. Do not handle it during or immediately after a preparation. n Do not place your hand or any other obstacle in front of the nozzle that can hinder the movement of

n If you do not set a cup in place or if you do so incorrectly, there may be risks of pinching or scalding.

n Do not put anything but ground coffee or the cleaning tablet in the funnel provided for this purpose;

do not add more than the maximum dose of ground coffee (1 spoon). In such a case, any damage

to the appliance will not be covered by the guarantee.

n In the event of a problem or incorrect operation, check the appliance and try to resolve the problem

(see Section 9: “Troubleshooting”) or have the appliance repaired if the problem persists.

n Always refer to the instructions for descaling/cleaning the appliance. Unplug from the socket before

any maintenance operation.

n Should cleaning or regular maintenance not be carried out or if there is a foreign body in the grinder

or in the ground coffee funnel, the guarantee will not be valid.

n This Espresso Automatic Series EA9000 coffee/espresso machine must only be used to prepare

espresso, coffee, hot water or to froth milk.

n This appliance is designed for domestic use only. It is not intended to be used in the following

environments and the guarantee will not apply for:

- staff kitchen areas in shops, offices and other working environments,

- by clients in hotels, motels and other residential-type environments,

- bed and breakfast-type environments.

n This Espresso Automatic Series EA9000 coffee/espresso machine is not designed for commercial or

professional use. Any use other than that described in this manual does not comply with these

recommendations and may lead to injuries and damage to equipment as well as damage or destruction

of the appliance (see Section 1.2, “Safety guidelines”).

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:41 Page8DEFRNLITEN

1.4 Products supplied with your machine

n Check the products supplied with your machine. If any parts are missing, contact our helpline (see

3.2: “Initial settings”).

Parts supplied: n Espresso Automatic Series EA9000n 2 bottles of steam nozzle cleaning liquidn 2 cleaning tabletsn 1 descaling sachetn Claris – Aqua Filter System cartridge with fitting accessoryn 2 cappuccino cupsn Ground coffee spoon with built-in brushn 1 stick for testing water hardnessn Instructionsn List of approved Krups service centresn Guarantee documentsn 1 power cordn 1 cleaning needle 1.5 Factory check

n Your appliance has been checked and tested before leaving the manufacturing plant. Despite all

the care given to its cleaning, you may find traces of coffee in the coffee grinder and/or coffee

drops on the drip tray grid. Thank you for your understanding. We also recommend that you rinse

the appliance one or more times before you use it for the first time or if you have not used it for

2.1 Description of the appliance

n The fold-out page shows a photo of the appliance. Fold out this page. The various controls of the

appliance are listed below with a brief description of them:

No. IDENTIFICATION FUNCTION

1 ON/OFF button To switch the appliance on and off.

2 Ground coffee button

To access the machine’s ground coffee function and to unlock

the ground coffee funnel.

3 Colour touch screen To access the recipes and other functions of the machine.

4 Removable water tank + lid Contains water for preparing recipes, cleaning and rinsing.

5 Used coffee collector Collects the used ground coffee.

Small drip tray and grid: can be

removed to position tall cups

To collect water or coffee that might flow out of the appliance

during/after preparation.

It can be removed to use taller cups (large recipes, caffe latte in

7 Large drip tray with metal contacts

Collects water flowing out of the appliance (when draining the

Thermoblock and hydraulic system) or water coming from the

8 Steam/hot water nozzle

To produce steam to heat or froth milk.

To produce hot water.

9 Steam/hot water tube

11 Steam nozzle cleaning container For automatic programmes that rinse and clean the milk nozzle.

12 Ground coffee funnel

Holds the ground coffee.

Holds the cleaning tablet during the automatic cleaning

ENGLISH No. IDENTIFICATION FUNCTION

13 Cup rest To hold and preheat cups.

14 Right door To access the water tank.

To access the cleaning liquid bottle, the ground coffee

spoon/brush and the used coffee collector.

height-adjustable handle

To dispense the prepared coffee recipe.

17 Power cord To supply power to the machine (removable).

18 Cleaning liquid bottle

Contains the product necessary for automatic cleaning of

19 Cleaning liquid bottle drawer Holds the cleaning bottle (fitting).

Ground coffee spoon with built-in

To measure the quantity of ground coffee necessary to

prepare a ground coffee.

The brush is used to remove ground coffee residue from

the ground coffee funnel.

21 Removable bean container lid

Closes the bean container. (Just open the removable lid

slightly using the notches on the side of the bean container.

Then it opens by itself.)

22 Coffee bean container

Holds the coffee beans and is equipped with automatic

23 LED cup lighting Illuminates your drink as it is being prepared.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:41 Page11KRUPS SERIE EA9000

2.2 Presentation of the different symbols

n The table below summarises all the symbols used on the screen:

To confirm the step.

To return to the previous step.

To scroll through the different options.

To bring the steam nozzle up in some menus.

To bring the steam nozzle down in some menus.

To go to the next step or stop a preparation in progress.

For example, during a cycle of cappuccino, to move from phase the foaming phase to the coffee

phase during coffee recipe or interrupt the coffee phase at the end of recipe.

To stop the cycle during preparation.

2.3 Main operations of the appliance

n Turning the appliance on or off

n Filling the bean container

Open the bean container lid.

Put in the coffee beans.

Close the bean container lid.

Press the “On/Off” button. n Put coffee beans into the container, which has a capacity of about 250 g. IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:41 Page12DEFRNLITEN

n Filling the water tank

Open the right door. Lift and pull the water

n The machine prompts you to fill the tank with water although there is water in it: Caution: The

machine includes a mechanism that manages the water level required for the requested recipe. It is

therefore normal that the water level is not always the same in the tank when there is a request to fill it.

n The machine does not detect my tank: Please check whether the tank has been inserted fully (until

you feel resistance).

Caution: Only put water in the tank!

n The machine prompts you to fill the bean container although there are beans in it: Some types of

coffee can interfere with optical sensors; you must shake the beans with your hand to make the function

operational once again.

n The machine detects beans, but the coffee dispensed is very/too light: Some beans (especially those

that are too large or too greasy) do not easily go into the grinder. Use your hand to ease them into the

grinder and/or change the type of coffee beans.

n The machine does not detect the absence of coffee beans: Check that a bean is not obstructing the

optical sensors. Otherwise, the function is not operational.

Caution: Never put ground coffee or water into the coffee bean container.

Ensure that no foreign bodies (e.g. small stones, hard wood) can get into the coffee bean

container as they could damage the grinder (not covered by the guarantee).

Danger: Any contact of the conductive parts of the appliance with humidity or water may lead to fatal

injuries due to the presence of electricity!

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:41 Page13KRUPS SERIE EA9000

At each stage check the messages on the touch screen

n Emptying the drip trays

Open the left door. Remove the used coffee

collector by pulling it

Empty the used grounds.

n Emptying the used coffee collector

Caution: Do not wash it in the dishwasher.

n Open the left door (15). Remove the used coffee collector (5). Empty and clean it before putting it back

Remove the small drip tray. Empty the small drip tray. Empty the large drip tray.

Wipe the metal contacts.

Remove the large drip tray.

Replace the large and small drip trays.

ENGLISH Your machine is supplied with two cups only which can be used for cappuccino or a caffe latte.* Caffe latte glass not supplied n Adjusting the coffee nozzle height

Caution: The cover and the grid can fall when you empty the drip tray.

Your machine has two drip trays (6 and 7).

n The small drip tray collects drips from the coffee nozzles but can be removed for preparations with

tall glasses. n The large drip tray collects used water and overflows from the small drip tray.n The large drip tray is fitted with an overflow detection sensor.n When it needs to be emptied, the request will be made on the screen.n The cover of this tray is necessary to avoid excessive condensation and water spills. n If the tray is dirty, clean it under running water. If the metal contacts are dirty, clean by scrubbing

them under water. Wipe the metal contacts dry before putting them back in the machine.

n The drip trays will be separated when you empty them. Avoid spilling water as much as possible on

the metal contacts located at the end of the drip tray.

n If the machine asks you to empty the drip tray when it is empty, check whether the metal contacts

at the back of the drip tray are clean and thoroughly dry.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:41 Page15KRUPS SERIE EA9000

INSTALLING THE APPLIANCE

n Place your machine on a stable, flat, heat-resistant surface away from water splashes and sources

of heat. Ensure that the location chosen is sufficiently well ventilated, as the appliance gives off

heat. Please do not place the appliance on surfaces such as marble. Remove the protective films

from the display and grids.

3.1 Before first use

n Before using the appliance for the first time, check the hardness of your water so that you can set the

appliance accordingly. This operation should also be carried out when you use your machine in a place

where the hardness of the water is different or if you notice a difference in the hardness of the water.

To check the water hardness, use the stick supplied with your machine or contact your local water

Measuring the water hardness

n Fill a glass of water and immerse the stick in it for 5 seconds. Wait for a minute before reading the water

hardness. You will be asked for the hardness class observed (from 0 to 4) during the initial setup of the

machine. The red zones on the stick indicate the degree of hardness: class 0 = no red zone, i.e. your

water has a very low mineral content. Your water is more or less hard depending on the number of red

zones. The details of the classes are given in the table below:

Class 0 Class 1 Class 2 Class 3 Class 4

The water hardness classes for the initial setting of the appliance (section 3.2)

Danger: Connect the appliance to an earthed mains socket. Voltage 220 - 240V. Failure to do

so means that you run the risk of fatal injury due to electricity! Respect the safety

guidelines (see section “Safety guidelines”).

n When your machine displays this screen to you, or when you have performed the water hardness

test, you must indicate the number of red and green zones, using the touch screen. If the stick

shows 2 red zones and 2 green zones, press the first two red squares and the last two green

squares on the touch screen. The screen will then show an identical representation of your stick.

If you move home or if the quality of your water changes significantly, you can also reset the water

hardness at any time.

3.2 Initial settings

n When using the machine for the first time, you will be prompted to configure various settings.

Follow the indications displayed on the screen. The aim of the following paragraphs is to give you

3.3 Configuring the settings

n Switch on the appliance by pressing the ON/OFF button (1). A welcome message is displayed on

the screen, followed by the “Language” setting menu. After each selection, you can go back by

using the symbol. Configure the other settings by following the indications on the screen.

The appliance will also require you to set the following parameters:

HOTLINE NUMBER FOR COUNTRY OF RESIDENCE

n This number is associated with the country you have selected. However,

you can change it and it may be changed at any time.

LANGUAGE n Your machine has a touch screen. n Select a display language by pressing the arrows until “Hello” appears

in the language of your choice. n Press OK to confirm. IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:41 Page17KRUPS SERIE EA9000

n The correct date should normally be displayed automatically. If necessary, you

can set the day, month and year using the arrows .

n To adjust the time, press the required time format (24H or AM/PM).

n You can choose the temperature level of your drinks, from level 1 (lowest

temperature) to level 3 (highest temperature).

n You can choose the length of time after which your appliance will switch off

automatically: from 15 minutes to 2 hours, in 15-minute periods.

n Set automatic switch-off using the arrows .

n Press OK to validate.

n You must set your machine according to the water hardness in your area,

between 0 and 4 (see P16 and P17).

n You can select the volume unit of measure of your choice from oz and ml.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:42 Page18DEFRNLITEN

ENGLISH Important: You must remember to run the install function every time you change the cartridge as soon as you can.

INSTALLING THE FILTER (LATER) n Press “Later” and confirm.n Remove the water tank from inside the right door.n Fill the water tank and then put it back in the machine.n Close the right door again. INSTALLING THE FILTER (NOW)

n Filter installation: press “Now“. n Open the right door of the machine and remove the water tank. n Remove the filter cartridge and the fitting accessory from the packaging

and assemble the cartridge fitting accessory as illustrated.

n Set the month when the cartridge is fitted (position 1 on the illustration,

left side figure in the opening) by turning the grey ring located on the

upper end of the filter. The month when the cartridge should be replaced

is indicated in position 2 on the illustration.

n Attach the cartridge fitting accessory to the filter cartridge as shown in

the illustration. n Lift the removable lid off the tank. n Screw the filter cartridge into the screw thread at the bottom of the water

tank: place the filter cartridge into the thread and screw in the cartridge.

Remove the cartridge fitting accessory from the filter cartridge. n Fill the water tank and then put it back in the machine. n Close the right door. Your machine will fill the filter cartridge.

n Your machine will fill the filter cartridge with water. This will take a few

seconds. You will then be asked to empty the larger drip tray.

Note: The filter cartridge must be replaced approximately every 50 litres of

water or at least every 2 months. Your machine tells you how many days or litres

remain before you need to change the cartridge. (see Section 7, “Info menu”)

INSTALLING THE CLEANING LIQUID

n Press “Now” to confirm or “Later” to do it later.

n Open the left door (15). Pull the container (19) and screw the bottle (18) onto

the container. n Replace the container back with the bottle and close the door.n Do not screw in the bottle fully.n The bottle must be positioned in line with the drawer. AUTOMATIC STEAM NOZZLE CLEANING PROGRAMME n Your machine will prompt you to start this programme. n To do so, press “Now“. The cycle will last about 5 minutes and the screen will

display the progress of the cleaning.

PREHEATING, AUTOMATIC MAINTENANCE, RINSING

n The machine will start by preheating the circuits, then will carry out an

automatic test and finally will ask you if the appliance needs to be rinsed or

n Place a container under the coffee nozzles and press YES if this is required.

The rinsing procedure starts and stops automatically, after around 40 ml have

passed through. n The main drink selection menu is then displayed on the screen. h

Important: Ensure that all of the lids, covers and doors are closed and that all parts of the machine are

fitted correctly before starting to prepare a drink.

Note: If the first use cycle is interrupted before it has fully completed, you will be asked to save certain

n Cappuccino is made with following proportions:

1/3 milk + 1/3 coffee + 1/3 milk froth.

You can obtain a maximum volume of around 300 ml.

n Caffe Latte is made with following proportions:

3/5 milk + 1/5 coffee + 1/5 milk froth.

You can obtain a maximum volume of around 260 ml.

n Hot milk with frothing is made with following proportions:

3/5 milk + 2/5 milk froth.

4.1 Information on recipes

n Depending on the recipes chosen, your Espresso Automatic EA9000 will automatically adjust the

quantity of ground coffee as well as the grinding fineness. We recommend that you use

appropriately sized porcelain cups, ideally preheated. For your milk-based recipes, we recommend

that you use thick glass cups.

Table of drinks and parameters modifiable by the user

Hot milk with frothing Final volume Milk

Hot water Final volume

From 20 ml to 250 ml

COFFEE RECIPES Number of cups

1 20 to 35 ml (per 5 ml)

40 to 70 ml (per 10 ml)

2x 40 to 70 ml (per 10 ml)

80 to 180 ml (per 10 ml)

n This section explains how to operate the machine using its features, taking the example of espresso

1 n Press the “Espresso” button on the touch screen. n If the machine detects no beans when you request this recipe, it will ask

you to fill the bean container (see section 2.3).

n If the machine detects no water when you request this recipe, it will ask

you to fill the tank. n Place the cup(s) under the coffee nozzles. n You can lower or raise the coffee nozzle to suit the size of your cup(s).

2 n Possible settingsn You can prepare one or two cups with your appliance. n Choosing the strength: The more beans you select, the stronger the

preparation will be. You can modify the strength using the arrows on the

left and right of the symbols (except in the case of double espressos).

n Choosing the volume: The screen displays the last volume setting

associated with espresso. You can modify this volume using the arrows

on the left and right of the indicated value .

n Press the “Start” button on the touch screen to start the preparation.

3 n Preparing an espresso n The machine starts preheating, if required, and then grinds the beans,

tamps the ground coffee and finally brews the coffee.

n You can adjust the coffee volume during the cycle using the up and down

n You can stop the preparation by pressing the “Stop” symbol or the On/Off

n Press the “Cappuccino” button on the touch screen.

n If the machine detects no beans when you request this recipe, it will

ask you to fill the bean container (see section 2.3).

n If the machine detects no water when you request this recipe, it will

ask you to fill the tank.

n Choosing the volume (small/medium/large).

n The screen shows the last volume setting associated with cappuccino

(volume of milk + volume of coffee + volume of froth). You can modify

this selection using the arrows on the left and right of the indicated

value (small – medium - large).

n Press the “Start” button.

n Fill the cup with the volume of milk indicated.

n Pour the quantity of milk indicated on the screen into the cup.

n Press the OK button.

Important: To prepare your Krups milk-based recipes to perfection:

n The recipes suggested were made with cold semi-skimmed UHT milk, straight from a refrigerator (7°C), and served

in the cups supplied with the machine.

n You can also use (fresh) cold pasteurised or UHT skimmed, semi-skimmed or whole milk, straight from the

refrigerator. What is important is that it should be fresh and at this temperature. Using special milks (microfiltered,

raw, fermented, enriched, etc.) can produce less satisfactory results especially when it comes to the quantity and

quality of the froth and therefore are not recommended.

n To guarantee the best results, we recommend that you follow the indicated proportions and use the cups supplied

n If you use a cup other than those supplied with the product, make sure you choose a cup suitable for the volume

in the recipe (taking frothing into account).

n If your milk is at room temperature, reduce the pre-heating time (press >> during the recipe).

n Milk frothing phase: The milk is then frothed according to the chosen

n You can increase or decrease the frothing time. (Make sure the cup does

n Press the “>>” button to stop the frothing and move on to preparing the

Important: The production of steam does not stop immediately after you press the “>>” button

(it takes 3 to 5 seconds to stop). Press the button sufficiently early to avoid overflows.

n The nozzle moves up and draws back to return to its cleaning container.

Caution: Caution: Do not place your hand or any other obstacle in front of the nozzle that can hinder

the movement of the nozzle.

Caution: If you do not set a cup in place or if you do so incorrectly, there may be risks of

If you press the Stop button, the entire recipe is stopped, and therefore the brewing will be

cancelled. The unused ground coffee will then be ejected.

n Place the cup under the coffee nozzles.

n The cup must be placed close to the cleaning container, under the steam

nozzle, at the back of the niche.

n However, do not press the cleaning container (11) with the cup; otherwise,

n You can lower or raise the coffee nozzle to suit the size of your cup. The

steam nozzle will descend just behind the coffee nozzles. Caution: the

maximum height of the cup is defined by the coffee nozzles; do not tilt the

cup to place it under the coffee nozzles.

n To use a large cup (or mug), you might have to remove the small drip tray (6).

n Press the “OK” button.

n Milk preheating phase: The milk is first preheated and during this

time the beans are ground for preparing the coffee.

n The nozzle moves forward and goes down into the milk

n The nozzle tip must be submerged in the milk by 1 cm for perfect results.

If this is not the case, the cup is not suitable for the volume chosen; stop

the preparation using the “Stop” button and change the cup.

n If the milk used is at an initial temperature higher than 7°C, you can

shorten the preheating time by pressing “>>” and move on to frothing to

avoid “spoiling” the recipe.

4.3 Preparing coffee-based drinks with ground coffee

n With your Espresso Automatic EA9000, you can prepare your drinks from ground coffee, if you

prefer decaffeinated coffee, if you want variety, or if you have run out of beans.

Caution: The volume available under the lid is the maximum quantity of ground coffee permissible.

Please put the ground coffee only once into the funnel for each recipe. Do not tamp the

ground coffee inside the funnel. If you open the lid and close it again without putting in

ground coffee, the machine will perform a self-test. If an object falls into the machine,

you must unplug it and take it to the after-sales service centre.

The ground coffee funnel is locked. To unlock it, press the ground coffee button.

ANY DAMAGE CAUSED BY INTRODUCING AN EXCESSIVE QUANTITY OF GROUND COFFEE WILL NOT BE COVERED BY THE GUARANTEE.

7 n Coffee dispensing phases.n The machine tamps the ground coffee and then brews it.n The volume is consistent with the chosen recipe.n However, you can modify the coffee volume during the cycle. n You can stop the preparation by pressing the “Stop” button. n Remove the cup when the screen shows: Your cappuccino is ready. n Add a little sugar or some chocolate chips/powder to taste. You must

add the sugar only at the end of the preparation.

8 n Automatic rinsing of the nozzle. n The nozzle is rinsed automatically after every milk-based preparation

to guarantee the hygiene of the machine.

n You must wait for this rinsing to be complete before starting the next

Important: Remember to take out the small drip tray when preparing a caffe latte.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:42 Page25KRUPS SERIE EA9000

4 n Use the coffee spoon (20) in the left door. 3 n Open the ground coffee funnel lid. n If you notice moisture inside the funnel, it is recommended that you wipe

1 n Press the ground coffee button. 2 n The ground coffee funnel is unlocked. n Press the “Espresso” button on the touch screen.

n If the machine detects no water when you request this recipe, it will ask

you to fill the tank.

n Espresso via the “ground coffee menu”

n This section describes how the recipes function when you use ground coffee via the ground coffee

funnel, taking the example of espresso. The other recipes are similar. Just follow the instructions on

the different screens.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:42 Page26DEFRNLITEN

4.4 Preparing other drinks: hot milk with or without froth, and hot

n Hot milk with frothing

1 n Press the “Hot Milk” button on the touch screen. n If the machine detects no water when you request this recipe, it will

ask you to fill the tank.

2 n Choosing: with or without froth. n Check the “Frothing” box if you want froth in addition to hot milk.

n When you choose a milk recipe “without frothing”, there can still be

a very fine layer of froth.

n Press the “Start” button to start the preparation. n Select the volume (small/medium/large). 5 n Introducing the ground coffee.n Pour the ground coffee into the funnel.n Use only one spoon of ground coffee for each recipe.n Close the ground coffee funnel lid.n The funnel is then locked by the machine. 6 n Choosing the volume. n Press the “Start” button.

7 n Preparing coffee.n The machine tamps the ground coffee and then brews it. n You can stop the preparation by pressing the “Stop” button.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:42 Page27KRUPS SERIE EA9000

n Press the “Hot water” button on the touch screen.

n If the machine detects no water when you request this recipe, it will ask

you to fill the tank.

n Fill the cup with the volume of milk indicated on the screen and

place it under the coffee spouts.

n The cup must be placed close to the cleaning container, under the steam

nozzle, at the back of the niche.

n However, do not press the cleaning container (11) with the cup; otherwise,

n You can lower or raise the coffee nozzle to suit the size of your cup. The

steam nozzle will descend just behind the coffee nozzles. Caution: the

maximum height of the cup is defined by the coffee nozzles; do not tilt the

cup to place it under the coffee nozzles.

n To use a large cup (or mug), you might have to remove the small drip tray (6).

n Press the “OK” button.

n Milk preheating phase.

n Milk frothing phase:

the milk is then frothed

according to the chosen recipe.

n The nozzle moves up and draws back to return to its cleaning

n Remove the cup when the screen shows: Your milk is ready.

n Rinsing the nozzle.

n The nozzle is rinsed automatically. You must wait for this rinsing to be

complete before starting the next preparation.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:42 Page28DEFRNLITEN

n Dispensing hot water through the steam nozzle.

n If necessary, the machine goes into preheating mode, then begins to

n You can modify the volume of your preparation using the arrows on

the left and right of the indicated value.

n Press “Stop” to stop the recipe.

Important: The production of hot water does not stop immediately after you press the “Stop” button

(it takes 3 to 5 seconds to stop). Press the button sufficiently early to avoid overflows.

n Press OK. The steam nozzle then comes out of its cleaning

container to stop just above your cup.

n You will need to modify the steam nozzle position using the + and -

symbols according to your convenience. If the steam nozzle is too high

from the bottom of the cup, there is a risk of splashing. Caution: The

nozzle must not touch the bottom of the cup either.

n Press the OK button on the touch screen.

n Choosing the volume.

volume using the arrows on the left and right of the indicated value.

n Place your cup under the coffee nozzles.

n To use a large cup (or mug), you must remove the small drip tray.

Make sure that the cup fits under the coffee nozzles without

n The cup must be placed close to the cleaning container.

n Caution: use a cup that matches the volume of the recipe. The

maximum height of the cup is defined by the coffee nozzles; do not

tilt the cup to place it under the coffee nozzles.

n Caution: Do not press the cleaning container (11) with the cup;

otherwise, it might break off.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:42 Page29KRUPS SERIE EA9000

n The “Favourites” menu on your Krups Espresso Automatic Series EA9000 allows you

to save your favourite recipes and to customise them to your tastes and habits. You

can create up to 8 profiles, which can contain up to 8 recipes each. The screens will guide

you very intuitively through this entire menu. This section aims to explain the various features

this programme offers you, taking the example of espresso.

n Customisable recipes are those in the main menu (see page 21).

n The following criteria can be customised, depending on the recipes: volume of coffee, coffee strength,

coffee temperature, volume of milk, preheating time and milk frothing time.

RECIPES STEP 1 STEP 2 STEP 3

Ristretto Choice of volume Confirm the name

Espresso Choice between 1 or 2 cups

Coffee Choice between 1 or 2 cups

1.Volume of cold milk

1.Volume of cold milk

2.Coffee strength (3) Confirm the name

Hot milk 1.Choice of frothing or not

1.Volume of cold milk

n Before creating customised recipes, you must create a user profile. * Allows you to increase the temperature of your recipe.** Allows you to increase the proportion of froth in your recipe. IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:42 Page30DEFRNLITEN

ENGLISH CREATING A PROFILE

1 n The first time you go to the “Favourites” menu, your machine will prompt you to create a new profile. Press the OK button.

n During subsequent uses, press the icon to create a new

2 n Then enter the name of your profile using the alphabetic keypad displayed on the screen and confirm by pressing OK.

n You must then select a colour for your profile. Choose it and confirm by

n Your profile will then appear in the Favourites menu. You can associate

up to 8 recipes with it. When you press the profile button, you will access

the list of recipes associated.

NB: At any time, you can:

n Create a new profile by pressing the + button

- You must then repeat the same operations, i.e. enter the name and choose the colour.

n Modify the profile characteristics by pressing the (Change) button.

- Choose the profile you want to modify

- Modify the name entered

- Confirm by pressing OK. n Delete one or more profile(s) by pressing the (Delete) button. - Choose the profile(s) you want to delete

- Confirm by pressing the OK button.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:42 Page31KRUPS SERIE EA9000

n After creating the profile, you can associate a recipe with this profile

by pressing the + button.

n Several recipes are then displayed on the screen. Choose the Espresso

recipe, in this case.

n Choosing the number of cups: Choose 1 or 2 cups by pressing the

n Choosing the coffee settings: Choose the volume (40 to 70 ml), strength

(1 to 3 beans) and temperature (levels 1 to 3) of the espresso you want to

store. Confirm by pressing OK.

n By default, a name is given to your Espresso recipe. You can decide to

keep it (by pressing OK) or modify it (by pressing Change).

n If you modify it, the indication Espresso will be present in the name and

you can add a suffix using the keypad. Then press OK to confirm the new

n Your recipe is then saved with its new name and appears in the screen

showing the recipes of the user profile in question.

n Example of espresso

NB: At any time, you can:

n Create a new recipe by pressing the + button

- You must then repeat the same operations of choosing the recipe settings.

n Modify the recipe characteristics by pressing the (Change) button.

- Choose the recipe you want to change

- Modify the recipe settings

- Modify the recipe name

- Confirm by pressing OK. n Delete one or more recipe(s) by pressing the (Delete) button. - Choose the recipe(s) you want to delete

- Confirm by pressing the OK button.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:42 Page32DEFRNLITEN

1 n Brightness n Increase or decrease the brightness of the screen of your appliance. n Press OK to confirm. n You can access the “Settings” menu from the main menu by

pressing the “Settings” tab.

n You can modify: the language, brightness, date and time, volume unit; but

also water hardness, coffee temperature and auto-off mode.

n To go back to the recipe sequence, press the small cup at the top

right-hand of the screen. n To quit the Settings menu: press the Settings tab. n Among the possible settings, you will find language, date and time, unit

of measure, water hardness and coffee temperature.

3 n To quit the settings menu n Go back to the Settings menu by pressing the symbol . Then press the Settings tab to return

to the main menu. n Press OK to confirm. 2 n Auto-off n Decide how long your appliance must remain turned on before turning

off automatically; between 15 minutes and two hours, in steps of 15

minutes. n Press OK to confirm.

n The “Settings” menu allows you to make changes to optimise your ease of use and suit your

preferences. Below are the main settings available. Just follow the instructions on the different

screens in the display.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:42 Page33KRUPS SERIE EA9000

1 n Cycles n Gives you information about your drinking habits, in terms of coffee or

milk-based drinks as well as the number of times you have prepared them

via the “Ground coffee” or “Favourites” menus. n Press OK to confirm. 2 n Helplinen Here you can find the helpline number for your country.n You can change it by pressing “Change”.n Press OK to confirm. 3 n Water filter n Tells you, where relevant, the last time the water filter was replaced and

next time the filter must be replaced. n You can also start a filter replacement procedure.n Press OK to confirm. n You can access the “Info” menu from the main menu by pressing the

n You can then view all the information available on time limits in terms of:

rinsing, descaling, replacing the filter, cleaning the nozzles, cleaning the coffee

circuit, changing the cleaning liquid and preparation cycles. n To quit the Info menu: press the Info tab.

n The “Info” menu provides information about your use and about certain stages in the life of your

machine. It also informs you about the maintenance of your machine. Below are the main details

available. Just follow the instructions on the various screens in the display.

n Gives you the number of rinsing cycles already carried out by the

n Press OK to confirm.

n Cleaning the coffee circuit – Descaling

n Tells you the number of brewing cycles performed since the last

cleaning/descaling and the number of cycles that can be performed

before the next descaling.

n You can also start a coffee circuit cleaning programme.

n Press OK to confirm.

n Automatic/manual cleaning of the steam nozzle

n Tells you the number of brewing cycles performed since the last

automatic/manual cleaning of the steam nozzle and the number of

cycles that can be performed before the next automatic cleaning of

n You can also start up an automatic/manual programme for cleaning

n Press OK to confirm.

n Tells you the number of cycles carried out since the last replacement

of the cleaning liquid bottle and the number of cycles possible before

the next replacement of the cleaning liquid bottle.

n You can also start a cleaning liquid bottle replacement programme.

n Press OK to confirm.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:42 Page35KRUPS SERIE EA9000

n Manual cleaning of the steam nozzle

The machine can ask you to clean the nozzle manually or can clean it on your request. Manual cleaning

is requested depending on the number and type of milk recipes prepared.

Below are the main steps in this manual cleaning of the nozzle when requested by the user. Otherwise,

just follow the instructions on the screens displayed by the machine.

8.1 Maintenance menu

n Press the Maintenance tab to access the Maintenance menu.

n Automatic cleaning of the steam nozzle

The machine can automatically clean the nozzle on your request, or automatically.

Automatic cleaning is required depending on the number and type of milk recipes prepared.

Below are the main steps in this automatic cleaning when requested by the user. Otherwise, just follow

the instructions on the screens displayed by the machine.

MAINTENANCE AND CLEANING

1 n You can access the “Maintenance” menu from the main menu by pressing the “Maintenance” tab. n Press the “Automatic cleaning of the nozzle” button on the touch screen.n NB: The cleaning cycle must not be interrupted.n To quit the “Maintenance” menu, press the “Maintenance” tab.n If necessary, the machine will ask you to replace the cleaning liquid bottle.

2 n Press Start. (if you do not do so immediately, you will return to the initial screen). n The machine starts by rinsing the nozzle.n The nozzle comes out of its cleaning container.n The cleaning liquid is introduced automatically into the nozzle cleaning container. n The machine mixes water with the cleaning liquid.n Then, the machine cleans the nozzle by soaking it in this mixture.n The nozzle is then rinsed twice with water.n The cleaning cycle is finished IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:42 Page36DEFRNLITEN

ENGLISH Caution: Risk of scalding while unscrewing; the temperature of the nozzle can be high (> 50°C).

n You can access the “Maintenance” menu from the main menu

by pressing the “Maintenance” tab.

n To clean the nozzle and its container, you must follow the sequence

shown in the Maintenance tab.

n Failure to follow this sequence may damage the system.

n Press the “Manual cleaning of the nozzle” button on the touch screen.

n To quit the “Maintenance” menu, press the “Maintenance” tab.

n The nozzle comes out of the cleaning container.

n You can clean all of the parts of the machine located behind the coffee

n Remove the two drip trays.

n Empty and clean them.

n The nozzle moves forward and slightly downward.

n Unscrew the nozzle tip (10) with the steam nozzle (9).

n Do not remove the tip seals, as this may damage them and affect the

frothing performance.

n Clean the three holes on the nozzle tip using the pin supplied for this

purpose with the Welcome Pack. You must fully separate the two

parts to clean them properly.

n Do not wash the tip in the dishwasher.

n Caution: clean the tip properly.

n Press the “OK” button.

n Replace the two drip trays (see visuals p. 13). n The manual steam nozzle cleaning cycle is finished. n Press OK to confirm and quit. Caution: The manual cleaning of the nozzle and the cleaning container must be carried out in this

sequence: If not, you risk damage to the steam nozzle assembly, malfunction or breakage.

6 n The steam tube moves down. n You can thus clean it properly with a damp cloth (you can use a little

washing-up liquid, but rinse it thoroughly). The steam tube cannot be

n Press the “OK” button. The steam tube moves up so that the nozzle tip

and the nozzle can be refitted.

7 n Re-screw the nozzle with the tip onto the steam tube.n Press the “OK” button.n The steam nozzle assembly moves up and stops above the cleaning container.

8 n Cleaning the steam nozzle cleaning container (11). n Press YES to the question: “Do you want to clean your cleaning container?”

if you want to clean it. n Press the top of the container to remove it. Clean it under running water.n To put the container back, first position the lower part and then press the upper part: you should hear a “click”. n Press the “OK” button. hh

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:42 Page38DEFRNLITEN

n Cleaning the steam nozzle cleaning container

n Cleaning the ground coffee funnel

2 n Open the ground coffee funnel lid.n Remove the ground coffee funnel. 1 n You can access the “Maintenance” menu from the main menu by pressing the “Maintenance” tab.

n You cannot clean the ground coffee funnel without going through the

Maintenance tab. Always follow the instructions given on the screen.

n Press the “Cleaning the ground coffee funnel” button on the touch

screen. n The ground coffee funnel lid is then unlocked.n To quit the “Maintenance” menu, press the “Maintenance” tab. 3 n Clean the ground coffee funnel. n You can clean it with the brush or under running water. Caution: Dry

it thoroughly. It must be dry when you replace it.

Caution: Do not force the funnel open; it is always locked when the recipes are prepared.

! n You can access the “Maintenance” menu from the main menu by pressing the “Maintenance” tab.

n To clean the nozzle and its container, you must follow the sequence

shown in the Maintenance tab. n Failure to follow this sequence may damage the system.n Press the “Cleaning container” button on the touch screen. n Then follow the instructions on the screen, referring to the visuals in

step 9 in the manual cleaning of the nozzle until you see the screen

on the right. n This cleaning cycle is finished. IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:43 Page39KRUPS SERIE EA9000

n Changing the cleaning liquid bottle

The machine can request the replacement of the cleaning liquid bottle, but you can also make this

1 n You can access the “Maintenance” menu from the main menu by pressing the “Maintenance” tab.

n You must always use this programme so that the counters can be updated.

n Press the “Changing the cleaning liquid bottle” button on the touch screen. n To quit the “Maintenance” menu, press the “Maintenance” tab. 2 n Open the left door (15).n Pull out the drawer (19) of the cleaning liquid bottle. n Unscrew the bottle to be changed. Use only Krups bottles. The use of other

products that are incompatible or not approved by Krups will invalidate

n Remove the cap from the new bottle of cleaning liquid then screw it onto

the drawer without turning too tightly (maximum one and a half turns) (19).

n Screw in the new bottle. Place the liquid bottle in the axis of the

drawer. n Screw at least two turns. 3 n Push the drawer to the back.n Close the door.n Press OK.n This programme is finished. h

4 n Replace the ground coffee funnel. n Close the funnel lid. The funnel lid is then locked. If the machine asks you

whether you have taken out the funnel: press the OK button on the touch

screen. n Cleaning of ground coffee funnel completed. h

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:43 Page40DEFRNLITEN

8.2 Automatic cleaning programmes

n Automatic cleaning programme of the coffee circuit

A message on the screen will indicate when a cleaning programme needs to be run for the appliance.

Cleaning is required around every 360 preparations.

To run this cleaning programme, you will need a recipient with a capacity of at least 0.6 litres which

can fit underneath the coffee nozzle, and a KRUPS cleaning tablet (two of which are supplied in the

The automatic cleaning programme has three phases: one cleaning cycle and two rinsing cycles. It

lasts around 20 minutes.

Protect your worktop from any splashes during the cleaning and descaling cycles, especially if it is

made of marble, stone or wood.

Here are the main steps in this programme. Otherwise, just follow the instructions on the screens

displayed by the machine.

Caution: To respect the guarantee conditions, the cleaning cycle must be carried out when the

appliance requests you not to postpone it further.

Caution: You are not obliged to carry out the cleaning programme immediately the appliance

requests it, but it must be carried out reasonably soon.

Only use KRUPS cleaning tablets otherwise the guarantee will not cover any material

damage caused by the use of other brands of tablets. Cleaning tablets are available from

your KRUPS After-Sales Service Centre.

1 n You can access the “Maintenance” menu from the main menu by pressing the “Maintenance” tab. n Press the “Cleaning coffee circuit” button on the touch screen.n To quit the “Maintenance” menu, press the “Maintenance” tab. 2

n Empty the used coffee collector, remove and empty the drip trays, and fill the water tank.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:43 Page41KRUPS SERIE EA9000

3 n Open the ground coffee funnel lid.n Remove the ground coffee funnel. n Clean the ground coffee funnel. You can clean it with the brush or under

running water. Caution: Dry it thoroughly. It must be dry when you replace

4 n Put the funnel back without closing the lid. 5 n Put the cleaning table into the funnel. n Close the funnel lid. You must run this programme right to the end. The

funnel is locked. n Press the OK button on the screen. 6

n Place a recipient with a capacity of at least 0.6 litres under the coffee

nozzles and press OK.

n Follow the instructions on the screen. Once the cleaning cycle is complete,

empty the recipient and put it back under the coffee nozzles and fill the

tank again with water. After the second rinsing, empty the recipient and

Caution: Make sure that the cleaning programme is completely finished.

If the cleaning programme is interrupted by a power cut or accidental unplugging of the ma-

chine, it must be started again from the beginning. A new cleaning tablet will be required in

this case. The programme must be started again completely in order to rinse the water cir-

cuit and eliminate any traces of harmful cleaning products.

n Automatic descaling programme of the steam circuit

A message on the screen will indicate when a descaling programme needs to be run for the

appliance. The frequency of this programme depends on the quality of the water used (the harder

the water, the more often the appliance has to be descaled) and on whether a Claris Aqua Filter

System filter is used or not. To run the descaling programme, you will need a recipient with a capacity

of at least 0.6 litres that may be placed underneath the coffee nozzles and the steam nozzle, and a

KRUPS descaling sachet (F 054 – a 40 g sachet is supplied in the Welcome Pack). The automatic

descaling programme has three phases: one descaling cycle and two rinsing cycles. The programme

lasts approximately 22 minutes.

Caution: To respect the guarantee conditions, the cleaning cycle must be carried out when the

appliance requests you not to postpone it further.

Caution: You are not obliged to carry out the descaling programme immediately the appliance

requests it, but it must be carried out reasonably soon. Only use KRUPS descaler sachets

supplied in the Welcome Pack; otherwise the guarantee will not cover any material damage

caused by the use of other brands of sachets. Descaler sachets are available from your

KRUPS After-Sales Service Centre.

n When the machine requests descaling, confirm to start the

n Empty the used coffee collector, take out and empty the drip trays.

n Remove the water tank.

n If you use the Krups Claris Aqua Filter System filter cartridge, remove

it before the descaling operation.

n Empty the water tank and then fill it with water up to the CALC mark.

n Pour the descaler into the water tank and put it back.

n Use a large spoon with a long handle to mix the water in the tank or

remove the water tank and carefully shake it from left to right until

the descaler is fully dissolved.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:43 Page43KRUPS SERIE EA9000

n Place a recipient with a capacity of at least 0.6 litres under the coffee

nozzles and press OK.

n The descaling phase will start.

n When the descaling is complete: Empty your recipient and put it

back, then empty the water tank, rinse it well and fill it again.

n The first rinsing will start.

n End of the first rinsing: Empty your recipient and replace it.

n End of the second rinsing and of the steam circuit descaling phase.

n The nozzle returns to its cleaning container.

n Refit the Claris Aqua Filter System filter, if necessary.

n Empty your recipient and fill the water tank.

Caution: During the descaling or coffee circuit cleaning programmes, water can splash quite strongly.

If required, place a paper towel on the drip tray.

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:43 Page44DEFRNLITEN

ENGLISH TROUBLESHOOTING

n If your machine is not operating correctly, try to resolve it by referring to this troubleshooting guide.

If the problem persists in spite of this, contact our helpline (See details at end).

PROBLEM / MALFUNCTION PROBABLE CAUSES CORRECTIVE ACTIONS The machine displays a failure,

the software hangs or your

machine has a malfunction. n Software problem.n Turn off and unplug the machine. Remove the filter cartridge. Wait

for 20 seconds and restart the

machine. n If the failure persists, note down the message on the screen and

call the KRUPS customer service.

The appliance does not switch

on when the ON/OFF button is

pressed. n Power failure or blown fuse.n The mains plug is not pushed into the mains socket correctly or into

the machine or the mains socket

is faulty. n The appliance is faulty.n Check the fuses of your electrical installation. n Check that the plug is correctly inserted into the socket or have

the socket repaired. n Have the appliance checked by a qualified technician.

You used pre-ground coffee and

the machine does not make

coffee. n You have poured too much pre-ground coffee or the

pre-ground coffee is too fine. n Use a mixture for espresso coffee machines.

The espresso or coffee is not hot

enough. n The temperature of the coffee is not set high enough. n The coffee cup is cold.n Check the coffee temperature in the “Settings” menu. n Programme your recipe using the “Favourites” function by

increasing the temperature. n Warm the cup by rinsing it with hot water before starting the

The coffee is too lightly coloured

or too weak. n There is not enough coffee in the coffee bean container. n Too much coffee is prepared.n Check that coffee is present in the container and that nothing is

obstructing the sensor (coffee

bean blocking in the front, etc.). n Reduce the quantity of water in the coffee.

The coffee dispenses too slowly. n The filter cartridge is clogged.n The machine may need cleaning/descaling. n Start a cleaning of the machine. n Remove/replace the filter

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:43 Page45KRUPS SERIE EA9000

PROBLEM / MALFUNCTION PROBABLE CAUSES CORRECTIVE ACTIONS The coffee is not creamy.

n The machine may need to run a

n The coffee is not fresh enough.

n Start a cleaning of the machine

n Try using fresher coffee beans /

The coffee grinder makes a

n Foreign bodies are inside the

n Check whether you can extract the

foreign body using a tool. Unplug

the machine before you do this.

n Contact the KRUPS Customer

No steam comes out of the nozzle.

n The nozzle or the nozzle support is

n The water used is not suitable for

n Wash the steam nozzle manually

(see section 8); clean and unblock

n Check that the steam nozzle is

screwed on properly.

n Empty the tank and remove the

Claris cartridge temporarily.

n Fill the water tank with mineral

water with high calcium content

(>100 mg/l) and carry out steam

cycles (5 to 10) consecutively into

a recipient until you get a

continuous jet of steam.

There is not enough milk froth.

n The steam does not come out

n The milk is not cold enough.

n See paragraph above.

n We recommend that you use cold

pasteurised or UHT milk, freshly

The milk froth is not fine enough.

n The steam does not come out

n The milk is not suitable.

n Check that the milk is fresh and

n Check that there is enough milk in

n Wash the steam nozzle manually

(see section 8); clean and unblock

n Check that the steam nozzle is

screwed on properly.

n We recommend that you use cold

pasteurised or UHT milk, freshly

IFU_EN_KR_COFFEEMAKER_BARISTA_0A10475_Mise en page 1 14/05/12 09:43 Page46DEFRNLITEN

ENGLISH PROBLEM / MALFUNCTION PROBABLE CAUSES CORRECTIVE ACTIONS Nozzle cleaning does not take

n No cleaning liquid.

n The milk used is not suitable.

n Check that your preparation does

not boil while heating or frothing.

If it does, reduce the heating

and/or frothing time.

n Check that the cleaning liquid

bottle is not empty.

n Carry out a manual cleaning.

n We recommend that you use cold

The water tank has been filled,

but the warning message is still

displayed on the screen.

n The water tank is not fitted

n The float at the bottom of the tank

does not move freely.

n The water tank is scaled up.

n Check and unblock the float if

n Reinstall the water tank properly

until you feel some resistance.

n Rinse the water tank under

running water and descale, if

The drip tray has been emptied,

but the warning message is still

displayed on the screen.

n The metal contacts are dirty.

n Clean and wipe the metal

contacts at the back of the drip

The used coffee collector has

been emptied, but the warning

message is still displayed on the

n The used coffee collector is not

n The used coffee collector has

been fitted back too quickly.

n Refit the used coffee collector.

n Wait for at least 8 seconds before

refitting the empty collector.

A power failure occurs during

n The appliance is automatically

reinitialised when it is switched

There is water underneath the

n The drip tray is not correctly fitted

n Check that the drip tray has been

fitted correctly and empty it if

Danger: Only a qualified technician is authorised to carry out repairs on the power cord and the

220 - 240V electrical system. Failure to respect this exposes you to fatal injuries due to

the presence of electricity! Do not use an appliance that is visibly damaged!

Note: Programming problems are often resolved by unplugging the appliance for about one minute and

then plugging it in again.

Voltage: 220-240V / 50 Hz Weight EA9 metal: 11.5 kg

Power: In operation: 1450 W Used coffee collector

Energy consumption: On standby: 0 W Small drip tray

Water tank: 1.7 l Large drip tray

Coffee bean container 280 g Cable length

Pump pressure: 15 bar

Ground coffee funnel

n Keep the original packaging to transport the appliance.

Before transporting or tilting the appliance, empty the used coffee collector, the bean container, the

water tank and the drip trays and remove the cleaning liquid bottle to avoid spilling water or the cleaning

or descaling product.

n The symbol on the appliance or its packaging indicates that this product may not be processed as

household waste. Therefore it must be taken to a waste collection centre for the recycling of electrical

and electronic equipment. By sorting waste and disposing of old equipment correctly, you are helping

to preserve the natural resources and preventing harmful consequences for the environment and

people’s health. To obtain more information on waste collection sites, please contact your retailer.

Caution: If the appliance is dropped without its packaging during transport, it is preferable to take it to an

After-Sales Service centre to have it checked and avoid any risk of fire or electrical danger.

Note: Your appliance contains many materials that may be recycled or recovered.