Ninebot KickScooter F2 - Electric scooter SEGWAY - Free user manual and instructions

USER MANUAL Ninebot KickScooter F2 SEGWAY

Dashboard & Power Button

Power Button: Press the button to turn on; press and hold the button for 3 seconds to turn off. When the KickScooter is on, press the button to turn on/off the headlight and the rear light, and press twice to switch between the speed modes.

Direction Indicator: When turning left or right, press the (left) or (right) switch on the direction indicator switch. Then the direction indicator will flash regularly which can be turned off by pressing the corresponding switch again.

Speedometer: It displays the current speed of the scooter, as well as error codes.

*After setting the starting speed to 0 mph (0 km/h), the KickScooter will automatically enter Parking mode (P) upon powered on, and the KickScooter is unable to accelerate with "P" displayed on the speedometer. Rider has to exit Parking mode (P) by squeezing the brake lever once or accelerating the KickScooter to over 1.86 mph (3 km/h) before riding.

Speed Mode: There are three modes available. The top speed is as follows:

*The top speed of Sport mode (S) and the acceleration speed can be adjusted via APP. (Current battery level will affect the maximum speed.)

Name	F2	F2 Plus	F2 Pro
Mode	051201U	051202U	051203U
ECO (Energy-saving mode)	9 mph (15 km/h)
D (Standard mode)	16 mph (25 km/h)
S (Sport mode)	18 mph (30 km/h)		20 mph (32 km/h)

Cruise mode: The symbol indicates that the cruise mode is activated.

*Enable Cruise mode via Segway-Ninebot APP, and it will function when rider presses and holds the throttle for more than 5 seconds, with the buzzer ringing a long beep. (KickScooter can not enter Cruise mode when its speed is slower than 3.1 mph (5 km/h).

Bluetooth: It indicates that the scooter has been successfully connected to the mobile device.

Battery Level: The total battery level equals 5 bars.

• The battery power is very low when the first battery bar is red. Please charge your KickScooter immediately.

2 Specifications

	Item	Parameter
Product	Name	Ninebot KickScooter F2	Ninebot KickScooter F2 Plus
	Model	051201U	051202U
	Length × Width × Height	Approx. 45 × 22.4 × 47.8 in (1143.5 × 570 × 1214 mm)
	Folded: Length × Width × Height	Approx. 45 × 22.4 × 19.1 in (1143.5 × 570 × 484 mm)
	Net Weight	Approx. 37.9 lbs (17.2 kg)	Approx. 39 lbs (17.7 kg)
Rider	Max. Payload	265 lbs (120 kg)
	Recommended Age	16-55 years
	Required Height	3'11"-6'6" (120-200 cm)
Machine	Max. Speed	Approx. 18 mph (30 km/h)
	Theoretical Range[1]	Approx. 25 miles (40 km)	Approx. 34 miles (55 km)
	Typical Range[2]	Approx. 18 miles (30 km)	Approx. 28 miles (45 km)
	Max. Slope	Approx.18%	Approx. 20%
	Traversable Terrain	Most of the flat road conditions and typical Belgian roads
	Operating Temperature	14-104°F (-10-40°C)
	Storage Temperature	14-122°F (-10-50°C); recommended: 50-86°F (10~30 C)
	IP Rating	IPX5
	Duration of Charging	Approx. 6.5 h	Approx. 8 h
Battery	Nominal Voltage	36 V ---
	Max. Charging Voltage	42 V ---
	Nominal Energy	367 Wh	460 Wh
	Nominal Capacity	10.2 Ah	12.8 Ah
	Charging Ambient Temperature	32-113°F (0-45°C)
	Battery Management System	Over-heating, short circuit, over-current, over-discharge and over-charge protection
Motors	Nominal Power	350 W	400 W
	Max. Power	700 W	800 W
Charger	Input Voltage	100-240V~50/60Hz
	Max. Output Voltage	42 V ---
	Rated Output	41 V --- 1.7 A
	Output Power	70 W
Tire	Tire Pressure	42-48 psi
	Tires	10-inch Self-sealing tubeless tires

[1] Theoretical Range: Tested while riding with a full battery, 165 lbs (75 kg) load, 77^ (25^) , 70% of max. speed on average on pavement.
[2] Typical Range: Tested while riding with a full battery, 165 lbs (75 kg) load, 77^ (25^) , at the max.speed on pavement.
* Some of the factors that affect range include speed, load, number of starts and stops, ambient temperature, etc.

	Item	Parameter
Product	Name	Ninebot KickScooter F2 Pro
	Model	051203U
	Length × Width × Height	Approx. 45.6 × 22.4 × 49.3 in (1158.5 × 570 × 1252 mm)
	Folded: Length × Width × Height	Approx. 45.6 × 22.4 × 20.8 in (1158.5 × 570 × 529 mm)
	Net Weight	Approx. 40.8 lbs (18.5 kg)
Rider	Max. Payload	265 lbs (120 kg)
	Recommended Age	16-55 years
	Required Height	3'11"-6'6" (120-200 cm)
Machine	Max. Speed	Approx. 20 mph (32 km/h)
	Theoretical Range[1]	Approx. 34 miles (55 km)
	Typical Range[2]	Approx. 28 miles (45 km)
	Max. Slope	Approx. 22%
	Traversable Terrain	Most of the flat road conditions and typical Belgian roads
	Operating Temperature	14-104°F (-10-40°C)
	Storage Temperature	14-122°F (-10-50°C); recommended: 50-86°F (10~30°C)
	IP Rating	IPX5
	Duration of Charging	Approx. 8 h
Battery	Nominal Voltage	36 V=
	Max. Charging Voltage	42 V=
	Nominal Energy	460 Wh
	Nominal Capacity	12.8 Ah
	Charging Ambient Temperature	32-113°F (0-45°C)
	Battery Management System	Over-heating, short circuit, over-current, over-discharge and over-charge protection
Motors	Nominal Power	450 W
	Max. Power	900 W
Charger	Input Voltage	100-240V ~ 50/60Hz
	Max. Output Voltage	42 V=
	Rated Output	41 V= 1.7 A
	Output Power	70 W
Tire	Tire Pressure	42-48 psi
	Tires	10-inch Self-sealing tubeless tires

[1] Theoretical Range: Tested while riding with a full battery, 165 lbs (75 kg) load, 77^ (25^) , 70% of max. speed on average on pavement.
[2] Typical Range: Tested while riding with a full battery, 165 lbs (75 kg) load, 77^ (25^) , at the max.speed on pavement.
* Some of the factors that affect range include speed, load, number of starts and stops, ambient temperature, etc.

Recommended Maintenance Schedule

To ensure safe riding, day to day care and regular maintenance are essential. You, the owner, have control and knowledge of how often you use your scooter, how hard you use it and where you use it. It is the owner's responsibility to perform regular checks and bring your scooter to authorized service center for inspection and service. Please refer to the maintenance schedule below.

Note: This maintenance schedule charges a service fee.

Item	Component	Maintenance method	Every 3 months	Every 6 months or every 310 miles (500 km)	Every 12 months or every 621 miles (1,000 km)	Every 36 months or every 9,230 miles (15,000 km)
Mainframe maintenance	Mainframe parts	Use a soft, wet cloth to wipe the mainframe clean.	✓	✓	✓	✓
	Tire pressure	Inflate tires to 42-48 psi	✓	✓	✓	✓
	Tire wear	Check if the tires are cracked, deformed, or significantly worn.		✓	✓	✓
	Screws on the stem top	Tighten the screws fixed with the handlebar and the stem. The suggested torque is 5.5±0.5 N·m.	✓	✓	✓	✓
		Tighten the screw on the throttle. The suggested torque is 3.5±0.1 N·m. Tighten the screws on the brake lever. The suggested torque is 5.5±0.1 N·m. Tighten the screws on the stem top. The suggested torque is 10±0.5 N·m.			✓	✓
	Screws on the folding mechanism	Tighten the screw fixed with the front fork and screw in the core position of the folding structure (visible after folding). The suggested torque is 10±1 N·m. Tighten the screws on both sides. The suggested torque is 12.5±1 N·m.		✓	✓	✓
	Disc brake base	Tighten screws to fix disc brake base. The suggested torque is 7.7±0.2 N·m.		✓	✓	✓
Function Inspection	Hub motor	To accelerate and decelerate, check if the hub motor is stalled or has abnormal sounds.			✓	✓
	Front wheel maintenance	Check if the front wheel is stalled or gets shaky, or the axis shaft is unbalanced.			✓	✓
Function Inspection	Brake adjustment	If the brake is too tight/loose, use the 4 mm Allen key to loosen the screw on the caliper. Then slightly adjust the brake line (decrease/increase the exposed length), and tighten the screw again.		✓	✓	✓
	Brake pads	Spin the wheels, the caliper should be aligned with the rotor and they shouldn't rub on the brake pads.			✓	✓
	Taillight	Squeeze the brake lever, the tail light works normally.		✓	✓	✓
	Headlight	Check the headlight and see if it lights brightly.		✓	✓	✓
	Direction indicators	Toggle the direction indicator button to the left/right respectively, check if the direction indicators on the left/right side flash normally.		✓	✓	✓
	Dashboard	Power on the scooter, the dashboard works properly.		✓	✓	✓
	Buzzer	Power on/off the scooter, the buzzer sound is normal.		✓	✓	✓
	Horn (Only for F2 Pro)	Press the horn button and the sound is loud.		✓	✓	✓
	Bell	Ring the bell and the sound is loud.		✓	✓	✓
	Throttle	Press and hold the throttle then release it, checking for acceleration and deceleration. Note: Release it, check if the throttle will back to the position.		✓	✓	✓
	Fault detection	After connecting with the Segway-Ninebot app: 1) Update the firmware to the latest version. 2) Check if the notification of the corresponding error code and possible causes will prompt when the scooter detects an error		✓	✓	✓
	Charging	Charge the scooter: 1) Check if the current battery power displays on the dashboard. 2) Check the LED indicator on the battery charger. Charging: red, Fully charged: green.		✓	✓	✓

Item	Component	Maintenance method	Every 3 months	Every 6 months or every 310 miles (500 km)	Every 12 months or every 621 miles (1,000 km)	Every 36 months or every 9,230 miles (15,000 km)
Function Inspection	Control buttons	Press or toggle the button 3 times without failure.		✓	✓	✓
	Turning	Test with left turns and right turns (the steering angle is 60). No resistance or lag when turning.			✓	✓
Important parts	Battery assembly	The battery need to be replaced when it is charged and discharged for 500 times or the total mileage is more than 6,213 miles (10,000 km). Note: It is recommended to charge once every 60 days for long-term storage.				✓
	Controller	After 3 years' or 9320 miles' (15,000 km's)riding, the abnormal parts of the kickscooter have to be replaced immediately.
	Hub motor
Functional parts	Front wheel assembly
	Throttle & Brake lever
	Front fork assembly
	Folding mechanism
	Brake disc
	Disc brake base
	Dashboard Cover

Certifications

This product is certified to ANSI/CAN/UL-2272 by TUV Rheinland.

The battery complies with UN/DOT 38.3.

The battery complies with ANSI/CAN/UL-2271.

Federal Communications Commission (FCC) Compliance Statement for USA

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Industry Canada (IC) Compliance Statement for Canada

This device complies with Industry Canada license-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

CANICES-3 (B)/NMB-3(B)

Neither Segway Inc. nor Ninebot is responsible for any changes or modifications not expressly approved by Segway Inc. or Ninebot. Such modifications could void the user's authority to operate the equipment.

FCC ID:2ALS8-KS0016

IC: 22636-KS0016

Trademark

Ninebot is the trademark of Ninebot (Beijing) Tech Co., Ltd; Segway and the Rider Design are the registered trademarks of Segway Inc., App Store®/App Store, Apple logo®/Apple logo, iPadOS®/iPadOS, macOS®/macOS, Find My™/Find My and Works with Apple Find My logo™/Works with Apple Find My logo are registered trademarks/trademarks of Apple Inc., registered in the U.S. and other countries. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. Google Play and the Google Play logo are trademarks of Google LLC. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Segway-Ninebot is under license. Other trademarks and trade names are those of their respective owners.

The KickScooter is covered by relevant patents. For patent information, go to http://www.segway.com

We have attempted to include descriptions and instructions for all the functions of the KickScooter at the time of printing. However, due to constant improvement of product features and changes of design, your KickScooter may differ slightly from the one shown in this document. Scan the QR code or visit the Apple App Store (iOS) or the Google Play Store (Android) to download and install the App.

Please note that there are multiple Segway and Ninebot models with different functions, and some of the functions mentioned herein may not be applicable to your unit. The manufacturer reserves the right to change the design and functionality of the KickScooter product and documentation without prior notice.

© 2023 Ninebot (Beijing) Tech Co., Ltd. All rights reserved.

(※The Segway-Ninebot App can support KickScooter with built-in Bluetooth)

Diagramme

F2/F2 Plus

Recommended Maintenance Schedule