CUBIA ISOLA GLOSS PLUS - Water heater FABER - Free user manual and instructions

Product type	Extractor hood (water heater)
Model	CUBIA ISOLA GLOSS PLUS
Brand	FABER
Dimensions (WxDxH)	90 cm x 50 cm x 80 cm (estimated)
Power supply	220-240 V, 50/60 Hz
Motor power	Not specified (estimated 200-300 W)
Number of speeds	4 (including a timed intensive speed)
Special functions	24H function (extraction 10 min/hour), Delay function (delayed stop 30 min), optional remote control
Filter type	Metal grease filters (dishwasher safe) + activated carbon filter (disposable)
Lighting	LED lighting with adjustable intensity (power not specified)
Air outlet diameter	120 mm or 150 mm
Version	External evacuation or recirculation (with carbon filter)
Material	Stainless steel and glass (comfort panel)
Noise level	Not specified (estimated 45-65 dB)
Energy class	Not specified
Filter maintenance	Metal filters: wash every 2 months; carbon filter: replace every 4 months
Safety	Automatic shutdown, filter saturation alarm, backdraft protection
Repairability index	Not communicated
Included accessories	User manual, mounting kit, PVC pipe, reduction flange

Frequently Asked Questions - CUBIA ISOLA GLOSS PLUS FABER

How to install the hood in external evacuation version?

For evacuation installation, use a rigid or flexible duct of 120 or 150 mm diameter. Connect the air outlet of the hood to a duct leading outside. Ensure the path is as short as possible and comply with local regulations. Refer to the Installation chapter in the manual.

How to maintain the metal grease filters?

Metal filters can be washed in the dishwasher or by hand with a neutral detergent. They must be cleaned as soon as the FG symbol appears on the display, or at least every 2 months. Let them dry completely before putting them back.

When to replace the activated carbon filter?

The activated carbon filter must be replaced when the FC symbol appears, or at least every 4 months. This filter is not washable or regenerable. The saturation alarm must be activated manually during installation (see manual).

How to reset the filter alarm?

To reset the alarm, turn off the lights and motor, then deactivate the 24h function if active. Press the E button for about 3 seconds until the display turns off.

Is the remote control included?

No, the remote control is optional. It uses a CR2032 battery (not included). To activate it, press the F button for 5 seconds with all loads off. The IR symbol confirms activation.

What to do if the hood does not turn on?

First check that the hood is properly connected and that the circuit breaker has not tripped. Ensure the bipolar switch is in the on position. If the problem persists, contact technical support.

How to clean the glass comfort panels?

The comfort panels (glass) can be cleaned with a soft cloth and a neutral liquid detergent. Do not use abrasive products, wet cloths, or water jets. Never put them in the dishwasher.

What is the minimum distance between the hood and the hob?

The minimum safety distance is 650 mm for electric hobs. For gas hobs, follow the hob manufacturer's instructions (usually 650-750 mm). Refer to the manual for exact measurements.

How to use the 24H function?

Press the E button to activate the 24H function. The hood extracts for 10 minutes every hour at speed 1. The 24 indicator shows. To deactivate, press the button again.

Where to find spare parts?

For any spare parts (filters, bulbs, remote control), contact Faber after-sales service. The contact details are on the manufacturer's website or in the manual.

USER MANUAL CUBIA ISOLA GLOSS PLUS FABER

For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know the operation and safety features of the appliance.

The wire connection has to be done by specialized technician.

• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
• The minimum safety distance between the cooker top and the extractor hood is 650~mm (some models can be installed at a lower height, please refer to the paragraphs on working dimensions and installation).
• If the instructions for installation of the gas hob specify a greater distance, this must be respected.
• Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.
• Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
• For Class I appliances, check that the domestic power supply guarantees adequate earthing.
• Connect the extractor to the exhaust flue through a pipe of minimum diameter 120mm . The route of the flue must be as short as possible.
• Regulations concerning the discharge of air have to be fulfilled.

• Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc.).

• If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker hood.

• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
• If the supply cord is damaged, it must be replaced from the manufacturer or its service agent.
• Connect the plug to a socket complying with current regulations, located in an accessible place.
• With regards to the technical and safety measures to be adopted for fume discharging it is important to closely follow the regulations provided by the local authorities.

WARNING: Before installing the Hood, remove the protective films.
- Use only screws and small parts supplied with the hood.
WARNING: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.
- Do not look directly at the light through optical devices (binoculars, magnifying glasses...).
- Do not flambé under the range hood; risk of fire.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Children should be supervised to ensure that they do not play with the appliance.

• The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
  Accessible parts may become hot when used with cooking appliances.
• Clean and/or replace the Filters after the specified time period (Fire hazard). See paragraph Care and Cleaning.
• There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
• The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Dimensions

Components

Ref.	Q.ty	Product components
1	1	Hood Body complete with: Controls, Light, Suction Unit, Filters, Lower Duct
7	1	PVC Pipe (fitted)
8	1	Inclinable grid (fitted)
9	1	Reduction flangeø 150-120 mm
10	1	Metal cover
Ref.	Q.ty	Assembly components
11a	2	SB 12/10 Plugs
	Q.ty	Documents
	1	Instruction Manual

Boring the wall

If you want to use the hood in suction version with the air outlet at the back of the hood, make sure to follow the indications given below in the drawing for a correct boring operation of the air outlet opening.

Type Hood	45	60	90
X	180	240	390

When installing the hood in recycling version it has to be taken into consideration that space remaining between the hood and the upper limit (ceiling or self) is at least 8-10 cm.

On the wall, trace:

• a vertical line up to the ceiling or top limit, at the centre of the area where you intend to fit the hood;
• a horizontal line at: 550 ~mm min. above the cooking hob;
• As shown, mark a reference point at 808mm above the horizontal reference line, and at X mm (X= see table in figure) to the right of the vertical reference line.
• Repeat this operation on the opposite side, checking levelling.
• Drill the points marked using a 12mm bit

• Insert plugs with screws and brackets 11a in the holes then tighten them.

• Adjust the two screws Vr of brackets 11a, by just placing them in position.

• Hook the hood body to the two brackets 11a.
• Pull the Comfort Panel to open it, remove the filters one by one, push them towards the rear part of the unit and pull downwards at the same time.
• From inside the hood body, tighten the screws Vr to level the body.

Connection

AIR OUTLET IN A DUCTING HOOD VERSION

When installing the hood in ducting version, basing on the installer's choice, a rigid or a flexible pipe with a 150 or 120mm is used in order to connect the hood to the air outlet piping. The pipe connection can be made on the upper part or on the rear side of the hood.

Before connecting the hood to the air outlet ducting remove the lateral air outlet grid 8 and the plastic tube 7. The adapting flange 9 has to be removed only in case the connecting diameter is 150.

REAR AIR OUTLET

• When drilling the air outlet hole in the wall proceed in accordance with the scheme in the part concerning the wall drilling.
• Use a pair of tongs when breaking the rear air outlet hole in the wall.
• In case the connection is made by using a 120mm pipe insert the reduction flange 9 on the hood body outlet.
• Fix the pipe with an adequate quantity of pipe clamps. This material is not supplied together with the hood.
• Remove the charcoal filter if present.
  Fix the metal cover 10 to the upper air outlet hole of the hood by using the screws supplied.

UPPER AIR OUTLET

• In case the connection is made by using a 120mm pipe insert the reduction flange 9 on the hood body outlet.
• Use a pair of tongs when removing the central part of the metal cover 10. Fix the cover to the air outlet hole of the hood by using the screws supplied.
  Fix the pipe with an adequate quantity of pipe clamps. This material is not supplied together with the hood.
• Remove the charcoal filter if present.

AIR OUTLET IN A RECYCLING HOOD VERSION

• In case the components requested for the recycling functioning have been removed earlier these have to be positioned again.
• Put the plastic tube onto the flange 7.
• Place the air outlet grid 8 on the air outlet. Make sure that the position of the grid is correct.
• Make sure that charcoal filters have been placed inside the hood.

ELECTRICAL CONNECTION

• Connect the hood to the mains through a two-pole switch having a contact gap of at least 3mm .
• Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan.

Control panel

Button	Function	Display
A	Turns the suction motor on and off at speed one.	Displays the set speed
B	Decreases the working speed.	Displays the set speed
C	Increases the working speed.	Displays the set speed
D	Activate intensive speed from any other speed, including motor off. This speed is set to operate for 6 minutes, after which the system returns to the speed that was set before. Suitable to deal with maximum levels of cooking fumes.	Displays HI and the time remaining once very second.
	Press and hold the button for approximately 5 seconds, with all the loads turned off (Motor and Lights), to turn the Activated Charcoal Filter alarm On and Off.	FC+Punto (2 flashes)-Alarm On. FC+Punto (1 flash)-Alarm Off.
E	24H function Turns the suction motor on at speed one and effects one 10 minute extraction every hour.	Displays 24 and the spot at the bottom right flashes once every second, while the motor is running. It is disabled by pressing the button.
	When the filters alarm is triggered, the alarm can be reset by pressing and holding this button for approximately 3 seconds. These indications are only visible when the motor is turned off.	FF flashes three times. When the procedure terminates, the indication shown previously turns off: FG indicates the need to wash the metal grease filters. The alarm is triggered after the Hood has been in operation for 100 working hours. FC indicates the need to change the activated charcoal filters, and also to wash the metal grease filters. The alarm is triggered after the Hood has been in operation for 200 working hours.
F	Delay function Activate automatic switch-off with a 30' delay. Suitable to complete elimination of residual odours. Can be activated from any position, and is disabled by pressing the button or turning the motor off.	Displays the operating speed and the spot at the bottom right flashes once a second.
	Press and hold the button for approximately 5 seconds, with all the loads turned off (Motor and Lights), to turn the Remote Control On and Off.	IR+Punto (2 flashes)-Alarm On. IR+Punto (1 flash)-Alarm Off.
G	Turns the lighting system on and off at maximum intensity.
H	Turns the Courtesy Lighting on and off.

REMOTE CONTROL (OPTIONAL)

This appliance can be commanded using a remote control, powered by a CR2032 type 3 V battery (not supplied).

• Do not place the remote control near heat sources.
• Do not discard the batteries with normal waste, they must be put into the specific containers.

Cleaning the Comfort Panels

Pull the Comfort Panel to open it.
- Disconnect the panel from the hood canopy by sliding the fixing pin lever.
- The comfort panel must never be washed in a dishwasher.
- Clean the outside by using a damp cloth and neutral liquid detergent.
- Clean the inside as well by using a damp cloth and neutral detergent; do not use wet cloths or sponges, or jets of water; do not use abrasive substances.
- When the above operation has been completed, hook the panel back to the hood canopy and close it by turning the knob in the opposite direction.

Metal grease filters

They can be washed in the dishwasher, and need to be cleaned whenever the FG sign appears on the display or at least once every 2 months use, or more frequently if use is particularly intensive.

Resetting the alarm signal

• Turn the Lights and the Suction motor off, then disable the 24h function, if enabled.
• Press button E (see the paragraph on Use).

Cleaning the Filters

• Open the Comfort panels by pulling on the recess.
• Remove the Filters one at a time, pushing them towards the back of the unit and at the same time pulling downward.
• Wash the Filters without bending them, and leave them to dry completely before replacing. (If the surface of the filter changes colour as time goes by, this will have absolutely no effect on the efficiency of the filter itself.)
• Replace, taking care to ensure that the handle faces forwards.
• Close the Comfort panels.

It cannot be washed or regenerated, and must be changed when the FC symbol on the display appears, or at least once every 4 months. The Alarm signal, if it has been activated, only appears when the Suction motor is turned on.

Activating the alarm signal

• In Recirculation Version Hoods, the Filter Saturation Alarm must be activated on installation or at a later date.
• Turn the Lights and the Suction Motor off.

• Press D and hold for approximately 5 Seconds:

• The message FC+Dot flashes twice, A.C. Filter saturation alarm ACTIVATED

• The message FC+Dot flashes once, A.C. Filter saturation alarm DEACTIVATED

CHANGING THE ACTIVATED CHARCOAL FILTER

Resetting the alarm signal

• Turn the Lights and the Suction motor off, then disable the 24h function, if enabled.
• Press button E (see the paragraph on Use).

Changing the Filter

• Open the Comfort panels by pulling on the recess.
• Remove the Metal grease filters.
• Remove the saturated charcoal filter by releasing the fixing hooks.
• Fit the new filter and fasten it in its correct position.
• Replace the Metal grease filters.
• Close the Comfort panels.

Lighting unit

• For replacement contact technical support ("To purchase contact technical support").

BbIpyCK BO3dYXA I3 BCACbIBAHOUeE BbITJXKNI

Iy cTaHOBKn BCaCbIBaIOIIe BbITKaKKn COeINHHt b ee C BbIyckHoi Tpy6oJ KecTKoH HIn rH6KOJ Tpy6ko J 150 HIn 120 MM IIO ycMOTpeHHIO MOHTaXHHka. Tpy6ka MoKeT BbIXOJNTb KaK CBepxY, TaK IN c3aIN BbITKaKKn.

IpeKJteeM IIpHCTyIHTb K coeINHeHHIO BcacbIaIOIIe Tpy6bl, ydaJIHTb peYIHPyeMYIO peIeTKy 8 H Tpy6Ky 7 H3 IBX, ecJIH OHN eIIe cHrTb. IepexoIHbI IaHeII 9 CJIeIyET BbHyTB ToJIbKO IJIa coeINHeHH Tpy6Kn 0 150.

BbIITyCK BO3IYXA C3AIN

• UTo6bI cIeJIaTb OTBepCTHe IJIa OTBeIeHnBaO3Jyxa, cJIeIyET IIpHJePJKBaTbCra CxEMbI, IIpHBeIeHHoB B pa3JIe "OTBepCTHe B cTeHe".
  KJIeIaMn OTKpbITb 3aJHHe BbIpyckHoe OTBepCThe BO3yxa.
  -Дя coeINHHeHnC trpy6KoI 120 MM BCTaBHTb IpeXOINHbI ΦJIaHeII 9 B bblIyckHoe OTBepcTne KOpIyca BbITJxKN.
  3aKpeINITb Tpy6ky CIEIHaJIbHbIMN Tpy6HbIMN 3aJHMamH. Heo6xoIHMbl MaTePnaJI He BXOJIHTB KOMIIJEKT IIOCTaBKH.
• EcJH ecTb, BbIHyTb ΦHJIbTpbl IIpoTHB 3aIIaXOB Ha aKTHBOM yTJIe.
• YCTaHOBHTb 3aJIyIiKy 10 Ha BepXHEM BbIyCKHOM OTBepCTHN BBITJAKKN IIpNJlaIaEMbIMN BNHTAMN.

BbIIYCK BO3IVXACBEPXV

-ДлcaоeINHHeHnCtpy6KoN0120MMBcTaBHTbIpeXOHNbI ΦJIaHeII9BbIYnCKHOOTBepCTHE KOpIyCa BbITJKKH.
KJIeIaMn BbHytB IeHTpaJIbHyIO aCtB 3aJIyIiKN 10 H 3aKeIITb ee Ha BepXHEM BblYCKHOM OTBepCTHN BbITJxKKN IIpIIaIraEMbIMN BHTaMn.
3aKpeINITb Tpy6ky CIEIHaJIbHbIMN Tpy6HbIMN 3aJHMamH. Heo6xoIHMbl MaTePnaJI He BXOJIHTB KOMIIJEKT IIOCTaBKH.
- EcJH ecTb, BbHyTb ΦHJIbTpbl IIpoTHB 3aIIaXOB Ha aKTHBOM yTJIe.

BbIpyCK BO3dYXA N3 ΦNJIbTPYIOUeBbITJXKKI

• EcJHn H3 ΦHJIbTpUIOIIeE BbITgKKn CHrTbI paHee yCTaHOBJIeHHbIe ee YacTH, IIOCTaBHTb HX Ha MeCTO.
  BcTaBHTb Tpy6Ky H3 INX 7 BO _JiaHeII
• IIpHbHHTHTb peRyJIHypeMyIO peIITky 8 K BbIyckHOMy OTBepCTHIO BO3Jyxa H IIPOBeHrTbe ee IIOJOKeHHe Ha Tpy6Ke.
• IIpoBepHTb HaJIHcHe ΦHJIbTpOB IIpoTHB 3aIIaXOB Ha aKTHBHOM yTJe.

3JIeKTPnueCKOEIOJIKJIOUOHEHNE

CoeINHHNtB BbITJgKc cceTBIM HAnpJKeHHem, yCTaHOHB INByXIOJIIOCHbI BBIKJIIOHApTeJIb C pa3BeJeHHem KOHTaKTOB He MeHee 3 MM.
CHTbIPOTHBOXKHPOBBIE HJIbTpBI (CMOTPH pa3JeYxOJ) IIOBOPHTb IIpaBUNbHOCTb IOJIooKeHHaPa3BeMa IINTaIOIIeFo Ka6eJI B PO3ETKE BBITAKH

A

B

C

D

E

F

G

H

PanaheIy npabJIeHnIa

aayy aallll lllllg iin gill ll

Aaalll aai jai aiiaai 1i:

a

Ae paa aie aie 1a

a_i a s j k

.（....）

.

J 8 J 1

a 1

1 1

ailllglllllllllllllllllllllllllll

（）gjgl jj1 4

（）

J 1

a a a a a a a a a a a a a a a a a a a a a a a a a a a a

a aabaae aae aee aee aee aee aee

j 120 150

aill gall 1al 1gall 1al

8Jn J 15j j Sj p 11j y j 10j 11j 12j 13j 14j 15j 16j 17j 18j 19j 20j 21j 22j 23j 24j 25j 26j 27j 28j 29j 30j 31j 32j 33j 34j 35j 36j 37j 38j 39j 40j 41j 42j 43j 44j 45j 46j 47j 48j 49j 50j 51j 52j 53j 54j 55j 56j 57j 58j 59j 60j 61j 62j 63j 64j 65j 66j 67j 68j 69j 70

.0150 2

all

Jzal 1

Jolall xcluay gll

9 90120

aiee 2011

jglal gdo jno cuiol a oJoll algall. Cuiiil Caiuabw yB

J 1

.0g j 10 c

gall

9 120

aiee

gall jlll 010 llll jll

a2jall jlll 1

jglal gdo joo cuiol a o jll al gall. ciuilll ciuulabw y w

Jg j 1

1 1

g a lgea g y jy jll ola! ayac ay ball cll sall

(3) a1 + a2 + a_3 = 6

.7 aaiilge ayssy

C

.

y

（jllg）JlJyLgSLLJyBlaall JyB 1. gnnnll gnnnll nnnnll gnnnll yg 1yRSLI Lg jn nn (aill o jil) 1gall jgl 1. gall jgl 0gall jgl

sill 4

a 1 aaii dall sjiie c i jlll lal lal lal lal

= ( x1,y1) , = ( x2,y2)