EUROSYS 10PM - Sound system PEAVEY - Free user manual and instructions

Brand	Peavey
Model	EuroSys 10PM
Product type	Powered speaker (active PA system)
Dimensions (approx.)	50 x 30 x 30 cm
Weight (approx.)	10 kg
Power supply	230 V AC, 50/60 Hz
Rated power	45 W continuous at 8 Ω / 65 W continuous at 4 Ω
Input sensitivity	0.4 V for 45 W at 8 Ω
Fuse	0.8 A, delayed
Inputs	2 parallel Jack sockets (line level)
Extension output	Socket for passive speakers 8 Ω min. (e.g., EuroSys 12M)
Equalizer	4 bands: 100 Hz, 1 kHz, 5 kHz, 10 kHz (±12 dB)
Volume control	Rotary potentiometer
Power-on indicator	Yes (LED indicator)
Power switch	Yes (on/off)
Power connector	IEC (with fuse holder)
Cabinet material	Wood (type not specified)
Maintenance and cleaning	Clean with a dry, soft cloth. Do not use solvents.
Safety	Disconnect before maintenance. Use only the specified replacement fuse.
General information	Designed for live or fixed sound reinforcement. Can be used as stage monitors.

Frequently Asked Questions - EUROSYS 10PM PEAVEY

What is the power of the EuroSys 10PM speaker?

The rated power is 45 Watts continuous at 8 Ω and 65 Watts continuous at 4 Ω.

How to connect the EuroSys 10PM to a mixing console?

Use the parallel Jack inputs (line level). Connect the console's 'monitor' output to one of the inputs.

Can I connect an additional passive speaker?

Yes, via the extension socket. The minimum impedance of the additional speaker must be 8 Ω (e.g., EuroSys 12M).

How to adjust the equalizer?

The equalizer has 4 bands (100 Hz, 1 kHz, 5 kHz, 10 kHz) with a boost/cut of ±12 dB. Use the faders to reduce feedback or adjust the sound.

What type of fuse is needed?

A delayed fuse of 0.8 A. When replacing, use an identical model.

Can the speaker be used as a stage monitor?

Yes, it is a versatile powered speaker suitable for monitors or main PA.

How to know if the speaker is powered on?

An LED indicator lights up when the power switch is turned on.

What is the required supply voltage?

The device operates on 230 V AC, 50/60 Hz.

What to do in case of technical problem?

First consult the manual, then contact your Peavey dealer for assistance.

How to clean the speaker?

Use a dry, soft cloth. Avoid chemical or abrasive cleaners. Always disconnect before cleaning.

USER MANUAL EUROSYS 10PM PEAVEY

EuroSys 10PM Powered Monitor Enclosure

OPERATING INSTRUCTIONS

EuroSys 10PM

Powered Monitor Enclosure

OPERATING INSTRUCTIONS

WARNING! TO PREVENT SHOCK OR FIRE HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE FROM CASE. NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL. REPLACE FUSE ONLY WITH ONE OF THE SAME TYPE AND SPECIFICATION.

Thank you for choosing Peavey's Eurosys 10PM powered monitor enclosure as part of your sound reinforcement system. We take great pride in the design and manufacture of our units and you can expect top performance and reliability. Your Eurosys 10PM has been rigorously tested before packing and despatch to your dealer. It has been designed to run from a nominal 230 Volt AC mains supply.

1. AMPLIFIER INPUTS

Use to connect line level signals from the monitor send of the mixer. Two sockets are provided to allow connection to further Eurosys 10PM powered monitors. (Daisy chaining).

2. VOLUME

This slider controls the level or volume of the enclosure.

3. 4 BAND GRAPHIC EQUALISER

Four sliders allowing up to +/- 12dB of adjustment at the centre frequencies of: - 100Hz, 1KHz, 5KHz and 10KHz. Use to assist with any feedback problems.

4. ~PILOT LIGHT

Illuminates when AC mains power is being supplied to the amplifier.

5. EXTENSION SPEAKER SOCKET

Allows connection of a further unpowered monitor with an impedance of 8 ohms. The power amplifier will develop full power into 4 ohms. (65 Watts).

6. POWER SWITCH

Use to turn the Eurosys 10PM ON or OFF

7. MAINS CONNECTOR & FUSE HOLDER

An IEC 320 combined mains connector and fuse holder is fitted. A separate 3-wire mains cord fitted with a moulded plug is supplied.

8. 13 AMP PLUG REPLACEMENT

As the colours of the wires in the mains lead or cord of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:-

• the wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol, or coloured green or green yellow.
• the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
• the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

WARNING - THIS APPARATUS MUST BE EARTHED

SPECIFICATIONS

POWER OUTPUT (TYPICALLY)

45 Watts into 8 ohms

65 Watts into 4 ohms

INPUT SENSITIVITY

0.4 volt for 45 Watts into 8 ohms

FUSE RATING

0.8 ampere anti surge.

POWER REQUIREMENTS

185 Watts at 65 Watts output

MAINS VOLTAGE REQUIREMENTS

230 Volts AC (only) 50 / 60Hz

IN CASE OF DIFFICULTY CONSULT YOUR AUTHORISED PEAVEY DEALER

Due to our efforts for constant improvement, features and specifications are subject to change without notice.

Great Folds Road, Oakley Hay , Corby, Northamptonshire, NN18 9ET, England

Tel: [phone] Fax: [phone]