BAR332ESA - Solar weather clock OREGON - Free user manual and instructions

USER MANUAL BAR332ESA OREGON

EARTH FRIENDLY OVERVIEW

The +ECO line embodies our commitment to environmental concems. Aware of threats facing the world we live in, Oregon Scientific" has combined technological know-how, practicality and style to create this line of environmentally friendly products. These products provide practical solutions while enabling you and us to fufil our environmental responsibility. 1 Simply detach the solar panel and face it directly towards 2 the sun for a few hours to receive the amount of energy necessary to power the device. Together we can improve the world we live in. œ ou & our»

1. le] : Remote sensor reception indicator and outdoor

2. Outdoor temperature

8. Indoor temperature

2 4: Weatherforecast

7. Q: Daily alarm is On

4. CH Toggle between outdoor temperature channels

Rechargeable battery status LED indicator (1-3) iitlte auto-toggle

10. HI: Outdoor remote sensor battery low 5. (1) View alarm status; set alarm

11. SE Main unit back-up batteries low / no battery

12. x: AC adaptor connected

6. Qt: Activate / deactivate alarm function

13. #: Rechargeable battery is low / solar panel detached

Rechargeable bay level incicator

15. ZONE: Time zone offset 1 2 3

16. Calendar / Clock with weekday / seconds |

CHARGING: charging in process FULL: batteries fully charged (when TEST is pressed) Solar panel TEST establish if battery is full Battery compartment REMOTE SENSOR LED status indicator Wall mount hole Battery compartiment RESET: Reset unit to default settings CHANNEL switch seen SOLAR PANEL This product uses two AAA rechargeable batteries which should be charged via the solar panel. For the batteries” first charge, it is strongly advised to charge it for at least 12 hours.

To charge the battery:

1. Detach solar panel by exerting downward pressure and

pullng at a 45° angle (approx.) away from main unit.

2. Insert 2 AAA rechargeable batteries in battery

compartment located at the back of the solar panel. Place ONLY NiMH type rechargeable batteries in the solar panel battery compartment. Do not charge non-rechargeable batteries.

3. Expose the solar panel directly to sunlight for

approximately 5-6 hours to charge the battery. The (ed) CHARGING LED on solar panel will light up indicating there is sunlight and unit is charging, MBA press and hoid TEST located at the back of the solar Li panel. (Green) FULL LED indicates batteries have been fully charged

4. Align holes with protruding plastic. Push solar panel

towards main unit and snap into place. 5-6 hours of battery charging will normally provide power to operate unit for 2 months. When the rechargeable battery is nearly flat or when solar panel has been detached, the (green) LED indicator on the main unit and & wil flash. + For best results when charging the battery, place the solar panel directiy with view to sunlight. + Direct solar panel as follows: Solar panel facing: if you reside in the: North Southem Hemisphere South Northem Hemisphere + Do not scratch the solar panel's surface or wipe it with strong detergent + Do not expose the solar panel to rain, snow or moisture: + The duration of the rechargeable battery's charging or operating time is determined by either the intensity of sunlight or the position of the solar panel towards the sun + Do not overcharge the batteries.

1 piece AAA battery In the case when the rechargeable battery is flat or nearly flat or when the solar panel has been detached, the AAA battery can act as backup power supply for the main unit

1. Remove the battery compartment located at the base

2. "Insert the battery, matching the polarity.

3. Press RESET after each battery change.

Power adaptor (not included) The adaptor powers the unit and can also be used for charging the rechargeable battery. When connected to the main unit, æ& will be displayed. ROME! re main unit and adaptor should not be exposed to wet conditions. No objects filed with liquid, such as vases, should be placed on the main unit and adaptor. REMOTE SENSOR This product can work with up to 3 sensors at any one time to capture temperature readings in various locations. To set up the remote sensor:

1. Slide open the battery compartment

2. Slide channel switch to select a channel (1, 2, 3)

Ensure you use a different channel for each sensor. Insert the battery, matching the polarities. Press RESET after each battery change. Close the battery compartment Press and hold SEARCH for 2 seconds to initiate a sensor search. ous Use alkaline batteries for longer usage and consumer grade lithium batteries in temperatures below freezing. The remote sensor reception icon will show the following status: ICONS MEANING our» Main unit is searching li +8 for sensor(s) A sensor channel has BE) 2] #12 | been found Hi No sensor found BMP ideal placements for the sensor would be in any location on the exterior of the home at a height of not more than 1.5 m (5 #) and which can shield i from direct sunlight or wet conditions for an accurate reading,

CLOCK RECEPTION This product is designed to synchronize its clock automatically with a clock signal. BAR332ES: EU: DCF-77 signal: within 1500 km (932 miles) of Frankfurt, Germany. BAR332ESU: UK: MSF-60 signal: within 1500 km (932 Li miles) of Anthom, England. BAR332ESA: WWVB-60 signal: within 3200km (2000 miles) of Fort Colis Colorado. To enable / disable clock signal reception: Press and hold À to enable or W to disable clock signal reception INOME! Reception takes 2-10 minutes. If the signal is weak, it can take up to 24 hours to get a valid signal. lf signal reception is unsuccessful, place your unit next to a window, press and hold À to force another signal search. Clock signal reception indicator: © o

To set the clock manually, disable the clock signal reception first.

1. Press and hold ©.

2. Press À / W to change the settings.

8. Press © to confirm.

The settings order is: time zone, 12/24 hr format, hour, minute, year, calendar mode (month — day / day — month), month, day and language. BAR332ES / BAR332ESU: Time zone offset sets the clock +1-23 hours from the received clock signal time. If you have deactivated the clock signal reception, do not set a value for time zone. NOMEÏ 1 you enter +1 in the time offset setting, this will give you your local time plus one hour. If you are in the US (BAR332ESA) set the clock to: PA for Pacific time CE for Central time MO for Mountain time EA for Easter time NOTE! The language options are English (E), German (D), French (F), ltalian (I), Spanish (S) and Russian (R). To select clock display: Press © to toggle between clock with seconds, clock with weekday and calendar. ALARM To set the alarm:

1. Press and hold (f+!) to enter alarm setting.

2. Press À / W to set hour / minute.

3. Press (f*) to confirm

Qindicates alarm is ON. To activate / deactivate alarm: Press À. To silence the alarm: + Press SNOOZE to silence it for 8 minutes

+ Press any key to tum the alarm off and activate it again after 24 hours. To display alarm: Press (t+1) TEMPERATURE To toggle temperature uni Press °C / °F. To toggle between each outdoor sensor’ readings: + Press CHrepeatediy

+ Press and hold C'Hfor 2 seconds to initiate auto toggle of outdoor channels. WEATHER FORECAST This product forecasts the next 12 to 24 hours of weather forecast within a 30-50 km (19-31 mile) radius:

à Sonate | 25m re: Sumy T 2 x UM4 (AAA) rechargeable over Bates LE | var cou B RG adeptor (no include) F 1 x UM-4 (AAA) battery (for backup) =) Guy LI (TEX 187 x 0.87 in) a lu Wag 629 (222 ounces wiout Date + + Transmission range | 30 m (98) unobstructed Temperature range _ | 20°C to 60°C (-4°F to 140°F) BACKLIGHT Power 1 x UME3 (AA) 1.5 V battery Press SNOOZE to activate backlight for 3 seconds. PRECAUTIONS RESET + Do not subject the unit to excessive force, shock, dust, temperature or humidity Press RESET to retum to the default settings. + Do not cover the ventilation holes with any items such as newspapers, curtains etc. SPECIFICATIONS + Do notimmerse the unit in water. I you spill liquid over it, dry it immediately with a soft, lint-free cloth + Do not clean the unit with abrasive or corrosive materials. TYPE DESCRIPTION Do not tamper with the units internal components. This LxWxH 158 x 87 x 55mm (6.2 x 3,4 x 22 in) invalidates {he warranty, Weight 280 g (9.88 oz) without battery + Only use fresh batteries. Do not mix new and old batteries.

+ Images shown in this manual may differ from the actual display. + When disposing of this product, ensure it is collected separately for special treatment. + Placement of this product on certain types of wood may result in damage to its finish for which Oregon Scientific will not be responsible. Consul the furniture manufacturers care instructions for information. + The contents of this manual may not be reproduced without the permission of the manufacturer. + Do not dispose old batteries as unsorted municipal waste. Collection of such waste separately for special treatment is necessary. + Please note that some units are equipped with a battery safety strip. Remove the strip from the battery compartiment before first use: NOME! The technical specifications for this product and the contents of the user manual are subject to change without notice. NOTE! Features and accessories will not be available in all countries. For more information, please contact your local retailer.

ABOUT OREGON SCIENTIFIC

Visit our website (www.oregonscientific.com) to learn more about Oregon Scientific products. If you're in the US and would like to contact our Customer Care department direct, please visit wwww2.oregonscientific.com/service/support asp For international inquiries, please visit: www2.oregonscientfic.com/aboutintemational.asp

EU-DECLARATION OF CONFORMITY

Hereby, Oregon Scientific, declares_that_this +ECO Solar Weather Clock (model: BAR332ES / BAR332ESU/ BAR332ESA) is in compliance with the essential requirements and other relevant provisions of Directive 1999/S/EC. À copy of the signed and dated Declaration of Conformity is available on request via our Oregon Scientific Customer Service. E CE & ©

COUNTRIES RTTE APPROVED COMPLIED

AI EU countries, Switzerland HD and Norway CAD FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressiy approved by the party responsible for compliance could void the user's authority to operate the equipment. INOMEL this equipment has been tested and found to compiy with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses and can radiate radio frequency energy and, ffnotinstalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: + Reorient or relocate the receiving antenna. + _ Increase the separation between the equipment and receiver. + Connect the equipment into an outlet on a circuit different from that to which the receiver is connected + Consult the dealer or an experienced radio / TV

DECLARATION OF CONFORMITY L

The following information is not to be used as contact for support or sales. Please visit our website at www2. oregonscientfic.com/service for all enquiries.

Name: Oregon Scientific, Inc. Address: 19861 SW 95th Ave. Tualatin, Oregon 97062 USA Telephone No.: 1-800-853-8883 declare that the product Product No. BAR332ES / BAR332ESU / BAR332ESA Product Name: +ECO Solar Weather Clock Manufacturer: … IDT Technology Limited Address: Block C, 9/F, Kaiser Estate, Phase 1, 41 Man Yue St, Hung Hom, Kowloon, Hong Kong is in conformity with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation.