Zeus Evolution ZXE3000/1 - Receiver Hifonics - Free user manual and instructions
Find the device manual for free Zeus Evolution ZXE3000/1 Hifonics in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Monoblock Amplifier |
| Brand | Hifonics |
| Model | Zeus Evolution ZXE3000/1 |
| Category | Receiver |
| RMS Output Power (@ 1 ohm) | 3000 W |
| RMS Output Power (@ 2 ohms) | 2000 W |
| RMS Output Power (@ 4 ohms) | 1200 W |
| Power Supply | 12 V DC, max current 300 A |
| Dimensions (L x W x H) | 530 x 220 x 55 mm |
| Weight | 4.2 kg |
| Low-pass Filter | Built-in, adjustable from 40 to 240 Hz |
| Subsonic Filter | Built-in, adjustable from 15 to 40 Hz |
| Speaker Level Input | Yes, with auto-detection |
| Level Remote | Included |
| Protection | Short circuit, overload, overheating, DC offset |
| Maintenance | Clean with a soft dry cloth |
| Spare Parts | 300 A fuse (AGC or ANL) |
| Repairability | Refer to a qualified technician |
Frequently Asked Questions - Zeus Evolution ZXE3000/1 Hifonics
What is the actual RMS power of the Zeus Evolution ZXE3000/1 amplifier?
The RMS power is 3000 W at 1 ohm, 2000 W at 2 ohms, and 1200 W at 4 ohms.
What type of fuse should I use for the ZXE3000/1?
Use a 300 A fuse of type AGC or ANL, mounted on the power cable.
How do I adjust the low-pass filter on this amplifier?
Turn the LPF (Low Pass Filter) potentiometer to select the cutoff frequency, typically between 40 and 240 Hz.
Can I use a 2 ohm subwoofer with the ZXE3000/1?
Yes, the amplifier is stable at 2 ohms and delivers 2000 W RMS.
How do I connect the level remote?
Plug the provided cable into the Remote Level jack on the front of the amplifier, then install the knob within reach.
What should I do if the amplifier goes into protection?
Check the connections, load (impedance too low), power voltage, and ventilation. If the Protect light stays on, reset the device by turning off the power for a few minutes.
What power cable gauge is recommended?
Use a minimum 4 AWG (21 mm²) cable, with a 300 A fuse within 30 cm of the battery.
Can the ZXE3000/1 operate in stereo?
No, it is a monoblock amplifier designed for a single subwoofer. For stereo setup, use two units.
How do I clean the amplifier?
Disconnect power, then wipe the casing with a soft dry cloth. Do not use chemicals or water.
What is the minimum required power voltage?
The amplifier operates on 12 V DC (10 to 16 V). Voltage below 10 V may trigger protection.
User questions about Zeus Evolution ZXE3000/1 Hifonics
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual Zeus Evolution ZXE3000/1 - Hifonics and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Zeus Evolution ZXE3000/1 by Hifonics.
USER MANUAL Zeus Evolution ZXE3000/1 Hifonics
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Hifonics
Model : Zeus Evolution ZXE3000/1
Category : Receiver