Zeus Extreme ZXT2000/1 - Receiver Hifonics - Free user manual and instructions
Find the device manual for free Zeus Extreme ZXT2000/1 Hifonics in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Monoblock Car Audio Amplifier |
| Model | Zeus Extreme ZXT2000/1 |
| Brand | Hifonics |
| Amplifier Class | Class D |
| Number of Channels | 1 |
| RMS Power Output (4 ohms) | 1000W x 1 |
| RMS Power Output (2 ohms) | 2000W x 1 |
| RMS Power Output (1 ohm) | 2000W x 1 |
| Frequency Response | 10 Hz – 250 Hz |
| Low-Pass Filter | Variable 50 Hz – 250 Hz |
| Subsonic Filter | Variable 10 Hz – 50 Hz |
| Bass Boost | 0 – 18 dB via remote |
| Input Sensitivity | 200 mV – 8 V |
| Remote Control | Included wired bass remote |
| Power Supply Voltage | 12 V DC (10 – 16 V) |
| Dimensions (L x W x H) | 14.2 x 5.9 x 2.1 inches |
| Weight | 5.5 lbs |
| Protection Circuits | Thermal, overcurrent, DC offset, short circuit |
| Fuse Rating | 2 x 30A (external fuses) |
| Cooling | Aluminum heatsink with fan |
| Maintenance | Clean with dry cloth; no internal serviceable parts |
| Safety | Disconnect battery before installation; avoid moisture |
| Repairability / Spare Parts | Contact Hifonics service center for repairs; no user-serviceable parts |
Frequently Asked Questions - Zeus Extreme ZXT2000/1 Hifonics
How do I wire the Hifonics Zeus Extreme ZXT2000/1?
Connect power (B+) to battery positive via fuse, ground (GND) to chassis ground, remote (REM) to head unit remote output, and speaker output to subwoofer(s). Use 4 AWG power wire minimum.
What is the recommended impedance for this amplifier?
The amplifier is stable down to 1 ohm. For maximum power, wire a single 1 ohm sub or two 2 ohm subs in parallel.
How do I set the gain properly?
Turn gain all the way down, set head unit volume to 75% of max, play a 50 Hz test tone, then increase gain until you hear distortion, then back off slightly.
Does the amplifier come with a remote bass knob?
Yes, it includes a wired remote bass level control that also allows bass boost adjustment up to 18 dB.
What fuse size is required?
Use two 30A ATC/ATO fuses (not included) on the power wire near the battery. Do not exceed 60A total.
Why is my amplifier going into protection mode?
Common causes: low impedance (below 1 ohm), overheating, short circuit, or voltage drop. Check wiring, ensure proper ventilation, and use a multimeter to verify voltage.
Can I bridge this amplifier?
No, it is a monoblock amplifier designed for a single channel. Bridging is not applicable.
What is the input sensitivity range?
The input sensitivity is adjustable from 200 mV to 8 V, allowing compatibility with most head units.
How do I clean the amplifier?
Disconnect power and wipe the exterior with a soft, dry cloth. Do not use liquids or cleaners. Ensure the heatsink and fan are free of dust.
Does this amplifier support high-level (speaker) inputs?
The amplifier has RCA inputs only. For high-level input, you need a line output converter (LOC).
User questions about Zeus Extreme ZXT2000/1 Hifonics
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual Zeus Extreme ZXT2000/1 - Hifonics and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Zeus Extreme ZXT2000/1 by Hifonics.
USER MANUAL Zeus Extreme ZXT2000/1 Hifonics
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Hifonics
Model : Zeus Extreme ZXT2000/1
Category : Receiver