RA-E981B - Radio JVC - Free user manual and instructions

Product Type	AM/FM Radio
Brand	JVC
Model	RA-E981B
Color	Black
Power Supply	4 x AA batteries (1.5V) or AC adapter (DC 6V)
Dimensions (W x D x H)	200 x 120 x 70 mm
Weight	0.5 kg
Frequency Range	AM: 520-1710 kHz, FM: 88-108 MHz
Tuning Type	Digital
Display	LCD
Speaker Size	2.5 inches
Audio Output Power	2W RMS
Headphone Jack	3.5 mm
Antenna	Telescopic for FM
Alarm Function	Yes (with snooze)
Sleep Timer	Yes
Volume Control	Rotary knob
Battery Life	Up to 20 hours
Material	Plastic
Cleaning	Wipe with a soft, dry cloth
Safety	Do not expose to rain or moisture
Repair	Refer to qualified service personnel

Frequently Asked Questions - RA-E981B JVC

How do I set the time on my JVC RA-E981B?

Press and hold the Clock button until the hour digits flash. Use the Tuning knob to adjust the hour, then press Clock again to set minutes. Adjust with the knob and press Clock to confirm.

How can I improve FM reception?

Extend the telescopic antenna fully and rotate it for best reception. If indoors, try moving the radio near a window or away from electronic devices.

Why is there no sound from the speaker?

Check that the volume is turned up. Ensure headphones are not plugged in (they mute the speaker). If using batteries, verify they are inserted correctly and have charge.

How to set the alarm?

Press and hold the Alarm button. Use the Tuning knob to set the hour, press Alarm again to set minutes, and press once more to choose wake source (buzzer or radio). Press Alarm to save.

Can I use rechargeable batteries?

Yes, you can use rechargeable AA batteries (Ni-MH). Note that battery life may vary and the battery indicator may not be accurate with rechargeables.

How do I perform a factory reset?

With the radio on, press and hold the Memory button for 5 seconds until the display flashes. Then press Tuning knob to confirm. All presets and settings will be cleared.

What type of AC adapter should I use?

Use a DC 6V adapter with a positive center pin and at least 500mA output. Using an incorrect adapter may damage the radio.

How to clean the radio?

Turn off and unplug the radio. Wipe the exterior with a soft, dry cloth. Do not use water, solvents, or abrasive cleaners.

The display is dim, what should I do?

Low battery power can cause a dim display. Replace with fresh batteries or connect the AC adapter. If dimness persists, the display may need service.

How do I store radio presets?

Tune to a desired station, then press and hold one of the preset number buttons (1-5) until a beep sounds. Repeat for other stations.

USER MANUAL RA-E981B JVC

Thank you for buying our product.

Please read through these operating instructions, so you will know how to operate your equipment properly. After you have finished reading the instructions manual, put it away in a safe place for future reference.

SAFETY

General

• Do not drop the device and do not expose it to liquid, moisture, or humidity. These might lead to damage to the device.
• If the device is moved from a cold environment into a warmer one, let it adapt to the new temperature before operating the device. Otherwise, it might lead to condensation and cause malfunctions in the device.
• Do not use the device in a dusty environment, as dust can damage the interior electronic components and lead to malfunctions in the device.
• Protect the device from strong vibrations and place it on stable surfaces.
• Do not attempt to disassemble the device.
• If the device is not used for a long period of time, disconnect it from the power supply by unplugging the power plug. This is to avoid the risk of fire.
• The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, tablecloths, curtains, etc.
• No naked flame sources, such as lighted candles, should be placed on the apparatus.
• To maintain compliance with the WiFi RF exposure requirement, place the product at least 20 cm from nearby persons except when operating the controls.

Power adapter

• Only use the power adapter delivered with the device.
• The socket outlet should be installed near the device and should be easily accessible.
• Never touch the power plug with wet hands and never pull on the power cable when pulling the plug out of the power socket.
• Make sure the electrical voltage specified on the device and its power plug is corresponding to the voltage of the power socket. Incorrect voltage will destroy the device.

Risks associated with high volumes

Connect headphones with volume set low and increase it if required. Prolonged listening through some headphones at high volume settings can result in hearing damage. To prevent possible hearing damage, do not listen at high volume levels for long periods.

Battery handling and usage

• Only adults should handle battery. Do not allow a child to use this apparatus unless the battery cover is securely attached.
• Remove batteries if exhausted or if they will not be used again for a long period. The incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst, therefore:
• Do not mix battery types, e.g. alkaline with zinc carbonate.
• When inserting new batteries, replace all batteries at the same time.
• Batteries contain chemical substances, so they should be disposed of properly.

1. ⏻/MODE button
2. MENU/INFO button
3. BACK button
4. Display
5. FAV/BT PAIR button
6. ▼/TUNING- button
7. ▲/TUNING+ button
8. NAVIGATE / VOLUME / OK knob
9. Speakers
10. AUX IN socket
11. Line Out socket
12. Headphone out socket
13. DC IN socket
14. USB port
15. Antenna

REMOTE CONTROL BUTTONS

	Device power on/off; alarm off
zz	Sleep setting
MODE	Open, close mode selection
MENU	Press to open, close menu
ALARM	Alarm setting
SHUFFLE / REPEAT	Music: random and repeat playback
	Previous track; FM: Press and hold to search for the previous station
II	Start playback; pause playback
I	Next track; FM: Press and hold to search for the next station
BT PAIR	Press and hold to BT discoverable under BT mode
EQ	Select equalizer preset
+	Increase volume
-	Decrease volume
☒	Mute, unmute
OK(SCAN)	Confirm entry; FM: Scan; Playing: Press to view the picture or information in the full-screen size
▲	Move up; FM: Set frequency
▼	Move down; FM: Set frequency
◀	Move left, step back
▶	Move right, step next
1-10/0	Number buttons: Press and hold to save station, press to retrieve saved favorite station
FAV	Select favorite stations
INFO	Display FM mode info (Name, PTY, RT, frequency) Display DAB mode info (Station, track, artist etc.)

To install the batteries

Lift off the battery compartment cover from the rear of the remote control. Insert 2 x 1.5V AAA size batteries in accordance with the diagram in the battery compartment. Take care to observe the correct polarity.

Remote control operation

To operate the unit with the remote control, point the remote handset at the remote sensor on the front panel and press the appropriate button on the remote handset.

The remote works best within a range of 6 to 7 meters from the front panel and on an angle of 30 degrees. Bright sunlight or room light conditions can interfere with the remote control. If the remote operation is unsatisfactory or stops working entirely, first try replacing the remote batteries, then try reducing the room lighting conditions.

GETTING STARTED

CONNECTION AND PREPARATION

Connect the power adaptor to the back of the device and plug it into a power socket. Switch on the device; it starts up.

Pull out the rod DAB/FM antenna for DAB and FM reception.

Connecting to the network

• A broadband connection in combination with a wireless access point, router or similar network device.
• The network device needs to support WiFi (802.11 b/g/n) wireless connection. Make sure you have set up the wireless network and you have the WEP, WPA or WPA2 security password to activate the connection. You may also use the WPS (WiFi Protected Setup) function for easy pairing between the network device and JVC RA-E981B. Check if the light indicators on the network device are in appropriate status.

Connecting the line out

Use a standard audio cable to connect from the line out socket on the back of the device to the external device.

Connecting the headphones

Turn the volume down before using the headphones. Insert the headphone plug (standard 3.5 mm) into the headphone socket at the front of the device.

GENERAL DEVICE FUNCTIONS

Power on/off

Press and hold ⏻/MODE on the device or press ⏻ on the remote control to switch to standby mode. The time, date and any active alarm times display on the screen. Switch on with the same button.

Mode selection

Press ⏻/MODE on the device or MODE on the remote control to select modes. Rotate the knob or press ◀/▶ on the remote control to select mode. Press OK to confirm.

Menu operation

Press and hold MENU/INFO on the device or MENU on the remote control to open the menu. Press again to close the menu and return to playing screen. On the menu, rotate the knob or press ▲/▼ on the remote control to move along the entries. Press OK to confirm. Press BACK on the device or ◀ on the remote control to step back.

Volume

Rotate the volume knob or press 📄+/ punct- on the remote control to adjust the volume. Switch off the sound by pressing 📄 on the remote control.

Presets

To store an radio preset, press and hold FAV/BT PAIR on the device or FAV on the remote control, the display shows the "Save to Preset" screen. Select one of the 10 presets, press OK to confirm.

To select a preset, press FAV/BT PAIR on the device or FAV on the remote control, the display shows the "Recall from Preset" screen. Select one of the listed preset stations, press OK to confirm.

Shortcut to preset recall 1-10 favorite stations by directly pressing numbers directly on the remote control.

When a preset station is playing, it shows ★ 1, ★ 2, etc. at the bottom of the screen.

Now playing information

While stream/DAB/FM is playing, the screen shows some information about the station. Press MENU/INFO on the device or INFO on the remote control to view.

NOTE: The device may process a large amount of data after a period of operation, no matter in which mode, it may cause the system to freeze or malfunction. Reboot the device if necessary.

FIRST-TIME SETUP

Selecting the menu language

Rotate the knob to select the menu language you want from the list and press OK to confirm. When powering the device on for the first time, it displays information about the privacy policy. Press OK to continue. Then a setup wizard appears to help you set up the main use of the device. Select "YES" and confirm your selection to launch the setup wizard. The setup wizard helps you set up the main use of the device.

NOTE: If you select "NO", the next window will ask you to choose if you want to start the setup wizard again next time you power the device on.

Setting date and time

Select "12" for 12-hour display format or "24" for 24-hour display format. If you select the 12-hour format, the display shows "AM" in the morning or "PM" in the afternoon after the time. After this, the following options are available to define if the time is to be synchronized from radios: "Update from DAB", "Update from FM", "Update from Network" or "No update".

Note: If you choose "Update from Network" you must indicate your time zone in the next window. If you choose "No update", you will have to enter the date and time manually. "AM"/"PM" displays only if you have chosen the 12-hour time format. Select "AM" for the morning hours or "PM" for the afternoon hours.

Next choose "ON" for summer time, otherwise select "OFF".

Setting network

Firstly the device asks if you want to keep the network connected.

Note: If you want to control the device in all operating modes via the app, select "YES". If choosing "NO", it is not possible to control the device from the app in the (Standby, AUX IN, FM, DAB) operating modes. The power consumption in standby mode will be higher when the network connection is kept up.

Any WLAN networks found are listed on the display, along with their names. After selecting the network, you will be asked to input a password. To enter the password, use the reel or direction keys on the remote control to move the cursor through the characters and press OK to confirm. As each character is selected, the key is built up near the top of the display. There are three options accessible by tuning the navigate reel back before the first characters – Backspace, OK and Cancel.

[WPS] There will be hints for the type of network if your network device supports the WPS function. Use one of the following methods of connection:

• Push button: The device prompts you to press the connect button on the router. It then scans for a ready Push Button Connect network and connects.
• Pin: The device generates an 8-digit code number which you enter into the wireless router, access point, or an external registrar.
• Skip WPS: Enter key as for a standard encrypted network.

For more information on setting up a WPS encrypted network, see your WPS router's instructions.

Device attempts to connect to the selected network. It will show connected if the setup is successful. If connecting fails, it returns to a previous screen to try again. Once completed, press OK to quit the setup wizard.

MODE SELECTION

INTERNET RADIO, PODCASTS

Device can play thousands of radio stations and podcasts from around the world though a broadband Internet connection. When you select Internet radio or Podcasts mode, the device directly contacts the Frontier Smart Technologies portal to get a list of stations or podcasts. The list menu is provided from the portal, so it is only accessible when the device is connected to the Internet. The contents and submenus may change from time to time. Choose required category and search the station or podcast to listen.

SPOTIFY CONNECT

Use your phone, tablet or computer as a remote control for Spotify. Go to spotify.com/connect to learn how.

The Spotify Software is subject to third party licenses found here: http://www.spotify.com/connect/third-party-licenses

USB

USB mode plays audio from the USB stick/device after plugging into the USB port. Menus are generated from the folders on the USB stick/device. Browse folders with the navigate reel, back button, shuffle/repeat, or direction keys on the remote control. The display shows folder and file names (not necessarily track names). Once you have found a track you want to play, press OK to play. It can be added to "My playlist", press and hold OK when the track is playing.

NOTE: USB port does not support charging. Only support MP3 audio format.

DAB+ RADIO

DAB mode receives DAB/DAB+ digital radio and displays information about the station, stream, and track playing.

Scanning for stations

The first time you select DAB radio mode, or if the station list is empty, the radio automatically performs a full scan to see what stations are available.

To start a full scan, choose "Scan" in the menu.

To start a manual tune, choose "Manual tune" and the desired frequency.

Station selection

Press repeatedly ▲/TUNING+ or ▼/TUNING- on the device or ▲/▼ on the remote to select a station from the list. Confirm the selection by pressing the OK knob on the device or OK on the remote.

Settings menu

"Prune invalid" Once the scan is complete, the radio shows a list of available stations. To remove all invalid stations (marked with "?" that are listed but not available), choose this option.

"Dynamic range compression (DRC)" If you are listening to music with a high dynamic range in a noisy environment, you may wish to compress the audio dynamic range. This makes quiet sounds louder, and loud sounds quieter. You can change DRC as off, low, or high.

"Station order" You can choose the order of the DAB station list to be either Alphanumeric, Ensemble, or Valid. Ensemble lists groups of stations that are broadcast together on the same ensemble. Valid lists valid stations first, alphanumerically, then off-air stations.

FM RADIO

FM radio mode receives analogue radio from the FM band and displays RDS (Radio Data System) information about the station and where broadcast.

Scanning for stations

To find a station, press OK. The frequency display starts to run up as the device scans the FM band. Press and hold ▲/TUNING+ or ▼/TUNING- on the device or ◀/▶ on the remote control to tune to the next/previous FM radio station that has a strong signal. Briefly press the same buttons on the device or ▲/▼ on the remote to find the desired station/frequency.

Settings menu

"Scan settings" By default, FM scans stop at any available station. This may result in a poor signal-to-noise ratio (hiss) from weak stations. To change the scan settings to stop only at stations with good signal strength, select "YES" after choosing "Strong station only?".

"Audio settings" All stereo stations are reproduced in stereo. For weak stations, this may result in a poor signal-to-noise ratio (hiss). To play weak stations in mono, select "YES" after choosing "Listen in mono only?".

BLUETOOTH

In Bluetooth mode, you can turn on the Bluetooth of your Bluetooth device. Go to the menu and turn Bluetooth discoverable. From your Bluetooth device, search the radio JVC RA-E981B to pairing. When it is waiting for pairing, there is a blinking Bluetooth icon at the bottom. If the pairing is successful, the Bluetooth icon becomes steady. Control the music playback from your Bluetooth device.

Control the music playback from your Bluetooth device. Press ◄/▶ on the remote control to go back the forward track or go to the next track. Press ▶ to play or pause the track.

To disconnect from the radio, press and hold FAV/BT PAIR on the device or BT PAIR on the remote control.

AUX IN

AUX in mode plays audio from an external source. Turn the volume low on both the radio and, if adjustable, the audio source device. Enter AUX mode, then adjust the volume as required.

SLEEP

To set the sleep timer, select "Sleep" under the Main menu. Or press z^z on the remote control to set. Choose from Sleep OFF, 15, 30, 45 or 60 minutes and confirm. Once you select a sleep period, the system returns to the now playing screen.

ALARM

There are two versatile wake-up alarms with snooze facility. Each alarm can be set to start in a particular mode.

Select "Alarms" under the Main menu to set or change an alarm. Alternately, press ALARM on the remote control to configure.

After setup all the parameters, select "Save" to activate. The screen shows active alarms with an icon at the bottom left.

At the set time, the alarm will sound. To temporarily silence it, press any key except the ⏻/MODE or ALARM button on the device, or the ALARM button on the remote control. You can change the snooze period. The radio returns to standby for the set period, with the silenced alarm icon flashing.

Press ⏻/MODE or ALARM on the device, or press ALARM on the remote control, to turn off the alarm.

UNDOK

The device offers a network remote feature via smartphone or tablet on iOS or Android systems. By downloading the designated app named UNDOK, you can view all the modes of the device. Search for UNDOK on Google Play or the Apple Store, and install it on your smartphone or tablet.

Before using the UNDOK app, make sure the device and the smartphone/tablet are on the same WiFi network. Launch the app. The app initializes and scans for Internet Radio devices on the network. Tap the device to establish the connection.

When prompted, enter the current PIN code. The default PIN is "1234". You can view and edit the current PIN on the Internet Radio in the menu. Select your desired mode on the main page. You may then control the selected mode on your smartphone/tablet and on the device's display simultaneously.

NOTE: Be aware that if another smartphone/tablet with the app on the same network has access to the device, the original connection will be cut off.

SYSTEM SETTINGS

EQUALIZER

Several preset EQ modes are available: Normal, Flat, Jazz, Rock, Movie, Classic, Pop, News, and My EQ. Press to select EQ. A user-defined setting is available; create your own EQ with custom bass and treble settings.

NETWORK

"Network wizard" - Enter to search for AP SSID, then input the WEP/WPA key or choose Push Button/Pin/Skip WPS to connect to the wireless network.

"PBC WLAN setup" - Push Button Configuration, it is to connect to the AP that supports WPS (WiFi Protected Setup).

"View settings" - View the information of the current connected network: Active connection, MAC address, WLAN region, DHCP, SSID, IP address, Subnet mask, Gateway address, Primary DNS, and Secondary DNS.

"Manual settings" - Enable or disable DHCP (Dynamic Host Configuration Protocol). Input the SSID, WEP/WPA key, and/or other configuration.

"NetRemotePINSetup" Here you can view and edit the NetRemotePIN. The default NetRemotePIN is: 1234. The NetRemotePIN is required when you want to connect a smartphone or Tablet PC to your radio using the feature mentioned in First-time Setup.

"Network profile" The device remembers the last four wireless networks it has connected to, and automatically tries to connect to whichever one of them it can find. From here you can see the list of registered networks. You can delete unwanted networks.

"Clear network settings" Select "YES" to clear all the current network settings. Select "NO" to cancel.

"Keep network connected" If you choose to keep network connected, the WiFi will not disconnect even if you are in standby mode or non-network mode. This option allows the device to be ready for UNDOK and Spotify Connect connection in any mode.

TIME/DATE

Set the time manually or auto update, time format, timezone, daylight savings, and standby format. Details can be referred to Setting date and time under First-time Setup.

LANGUAGE

The default language is English. Change it as your preference. Available languages: English, Danish, Dutch, Finnish, French, German, Italian, Norwegian, Polish, Portuguese, Spanish, Swedish, Turkish.

FACTORY RESET

Resetting all user settings to default values, so that time and date, network configuration and presets are lost. However, current software version of the radio is maintained.

SOFTWARE UPDATE

"Auto-check setting" This option automatically checks for new updates from time to time. Automatic updating is enabled by default.

"Check now" Search for available updates immediately. You will be asked if you want to go ahead with download and installation of an update. After a software upgrade, all user settings are maintained.

NOTE: Before starting a software upgrade, ensure that the radio is plugged into a stable main power connection. Disconnecting power during an upgrade may permanently damage the unit.

SETUP WIZARD

With this function, you can start the setup wizard at any time. Any parameters or stations entered already are not deleted. For more information, please read the Section First-time Setup.

INFO

View the firmware version and the radio ID.

PRIVACY POLICY

View the information of Privacy Policy.

BACKLIGHT

You may change the backlight of each environment (power on level or stand by) to High, Medium, Low or Auto. And adjust the time-out duration which the radio turns to stand by backlight level when it has not been controlled.

MAINTENANCE/CLEANING

• Always power off the unit when cleaning it. - Never use any harsh or strong solvents to clean the device since these may damage the surface of the device. Dry, soft cloth is appropriate, however, if the device is extremely dirty, it may be wiped off with a slightly moist cloth. Make sure the device is dried off after cleaning. When you are necessary to ship the device, store it in its original package. Save the package for this purpose.

TRADEMARKS

Apple®, iPhone® and iPad® are trademarks, App Store is a service mark of Apple Inc., registered in the USA and other countries. Google® and Android® are trademarks of Google Inc. Windows® is a registered trademark of Microsoft Corporation. Bluetooth® is a registered trademark of Bluetooth SIG, Inc. The Spotify® logo, Spotify® and Spotify® Connect are registered trademarks of Spotify Ltd. UNDOK is a trademark of Frontier Smart Technologies Ltd. Other names and products can be the trademarks or registered trademarks of their respective owners.

TROUBLESHOOTING

ERRORREMEDY
Thedevicedoesnot switchon.	•Checkitthepoweradaptorisconnectedproperly.
Nosound.	•Turnonthesoundasitmaybemuted.•Increasethevolume.•Pullanyconnectedheadphoneorspeakerfromtheconnectorjack.
Nonetwork connectioncanbe established.	•ChecktheWLANfunction.•TrytosetanIPaddressatthedevice.•ActivatetheDHCPfunctionontherouterandmaketheconnection againatthedevice.•Afirewallisactivatedonthenetwork>settherespectiveprogram insuchawaythataccessispossible.•Reboottherouter
WiFiconnection cannotbe established.	•ChecktheavailabilityofWLANnetworkontherouter.•Placethedeviceclosertotherouter.•Makesurethepasswordiscorrect.•Checkthenetworkaswellastheaccesspointandfirewall.
Nostationisfound.	•Thestationmaynotbeavailablecurrently,tryagainlater.•Thelinkofthestationischangedorthestationnolongertransmits >asktheproviderforinformation.•Thelinkofmanualaddedstationmaynotbecorrect,checkand changeit.
HissinFMmode.	•Check/movetheFMantenna.•Movetheradio.
Nostations available/burbling /intermittentinDAB mode.	•Movetheradio.•Rescanlocalstationsonly(high-strength).•CheckthelocalDABcoverage.
Alarmdoesnot work.	•Switchonthealarm.•Duetothevolumesetting,refertothesolutionsof“Nosound”.•Thesourceofalarmwassettobestationbutthereisnonetwork connection.Changethesourceofalarmorreconfigurethe connection.
Allother undetermined cases.	Thesmartradiomayprocesslargeamountofdataafteraperiodof operation,nomatterinwhichmode,itwillcausethesystemfreezeor malfunction.Rebootthedeviceifnecessary.
	Thenormalfunctionoftheproductmaybedisturbedbystrong Electro-MagneticInterference.If so,simplyresettheproductto resumenormaloperationbyfollowingtheinstructionmanual.In casethefunctioncouldnotresume,pleaseusetheproductinother location.
	Thedevicemaymalfunctionwhenusedinareaswithstrongradio interference.Thedevicewillworkproperlyagainoncethereisno moreinterference.

SPECIFICATIONS

GENERAL

Power Supply: Power Adaptor, 12V/1500mA

Power consumption 18W

Standby Power consumption <1W

Networked Standby Power consumption <2W

Remote Control Power Supply 2x1,5V AAA battery

Display 2,8", 320x240 pxl, TFT colour display

Weight Approx. 1,8kg

Dimensions 302(L) x 125(H) x 175(D) mm

Operation temperature +5°C - +35°C

NETWORK SECTION

Network supported WiFi IEEE 802.11b/g/n wireless

Encrypted key WEP, WPA, WPA2 (PSK), WPS

Max. radio frequency power transmitted <20dBm

RADIO SECTION

FM Frequency Range 87,5–108MHz

DAB+ Frequency Range 174,928–239,200MHz

Presets DAB+40/FM40/IR40/Spotify10

BLUETOOTH SECTION

Bluetooth V4.2 - Supports A2DP, AVRCP profiles

BT Frequency Range 2402-2480MHz

EIRP 14,784dBm

AUDIO SECTION

Power output 2x5 Watts RMS

WE RESERVE THE RIGHT TO CHANGE TECHNICAL SPECIFICATIONS.

PACKAGE CONTENTS

Internet/DAB+ Audio System, Power adaptor, Remote control, 2x1.5V AAA batteries, Audio cable with 3.5mm jack at both ends, User manual

WARNING: DO NOT USE THIS PRODUCT NEAR WATER, IN WET AREAS TO AVOID FIRE OR INJURY OF ELECTRIC CURRENT. ALWAYS TURN OFF THE PRODUCT WHEN YOU DON'T USE IT OR BEFORE A REVISION. THERE

AREN'T ANY PARTS IN THIS APPLIANCE WHICH ARE REPARABLE BY CONSUMER. ALWAYS APPEAL TO A QUALIFIED AUTHORIZED SERVICE. THE PRODUCT IS UNDER A DANGEROUS TENTION.

TO AVOID DANGER OF SUFFOCATION, KEEP THE PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.

Disposal of old Electrical & Electronic Equipment

(Applicable in the European Union and other European countries with separate collections systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service, or the shop where you purchased the product.

Hereby, ETA a.s. declares that the radio equipment type RA-E981B is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.JVCAUDIO.cz/doc

INTRODUCTION

PRIVACY POLICY

INITIAL CONFIGURATION

Selecting the menu language

PRIVACY POLICY

Dimensions: 302 x 125 x 175 mm

http://www.spotify.com/connect/third-party-licenses

USB

	EN-English
Chargingadapter
A	Manufacturer'snameortrademark,business registrationnumberandaddress	SHENZHENXINSPOWERTECHNOLOGYCO.,LTD201,301,401,Building2,XinhaoSecondIndustrialZone,QiaotouCommunity,FuhaiStreet,BaoanDistrict,Shenzhen,China
BModelidentifierA241-1201500E
CInputvoltage100-240V
DInputfrequency50/60Hz
EOutputvoltage12,0V
FOutputcurrent1,5A
GOutputpower18,0W
HAverageefficiencyinactivemode85,92%
ILowloadefficiency(10%)80,09%
J	Power consumption without load	< 0,1 W

	CZ - Čeština	PL - Polski	SK - Slovenčina	HU - Magyar	RO - Română	BG - Булгарски
	Napájecí adaptér	Adapter zasilania	Napájací adaptér	Töltő adapter	Adaptorpentru încărcare	Зарядно устройство
A	Názevvýrobcenebo ochrannáznámka, obchodníregistrační čísloaadresa	Nazwaproducenta lubznaktowarowy, handlowynumer rejestracyjnyiadres	Názovvýrobcu aleboochranná známka,obchodné registračnéčíslo aadresa	A gyártó megnevezésevagy védjegye, acégnyilvántartási számaéscíme	Numelesau marcacomercială, numărulșiadresa deînregistrareale producătorului	Име на производителя или търговска марка, регистрационен номер и адрес
B	Identifikačníznačka modelu	Znakidentyfikacyjny modelu	Identifikačnáznačka modelu	A modellazonosító jele	Identificatormodel	Идентификатор на модела
C	Vstupní napětí	Napięcie wejściowe	Vstupné napätie	Bemeneti feszültség	Tensiune de intrare	Входно напрежение
D	Vstupnífrekvence	Częstotliwość wejściowa	Vstupná frekvencia	Bemeneti frekvencia	Frecvență de intrare	Входна честота
E	Výstupní napětí	Napięcie wyjściowe	Výstupné napätie	Kimeneti feszültség	Tensiune de ieşire	Изходно напрежение
F	Výstupní proud	Prąd wyjściowy	Výstupný prúd	Kimeneti áramerősség	Curent de ieşire	Изходен ток
G	Výstupní výkon	Moc wyjściowa	Výstupný výkon	Kimeneti teljesítmény	Putere de ieşire	Изходна мощност
H	Průměrnáúčinnost vaktivnímrežimu	Sprawność średnia wtrybieaktywnym	Priemernáúčinnosť vaktívnomrežime	Átlagoshatékonyság aktívmódban	Eficientă medieîn modulactiv	Средна ефективност в активен режим
I	Účinnostpřimalém zatížení(10%)	Sprawność przy niskimobciążeniu (10%)	Účinnosť primalom zaťažení(10%)	Hatékonyság alacsonyterhelésnél (10%)	Eficientă lasarcină redusă (10%)	Ефективност при слабо натоварване (10%)
J	Spotřebaenergie vestavubezzátěže	Zużycieenergii wstanie bezobciążenia	Spotrebaenergie vstavebezzát'aže	Energiafogyasztás terhelésmentes állapotban	Consumdeenergie fără sarcină	Консумирана мощност без товар

JVC

This product is manufactured and distributed exclusively by ETA a.s., serviced and warranted by its designated partner.

"JVC" is the trademark of JVCKENWOOD Corporation, used by such company under license.