The Skypad 2.0 - Range hood FABER - Free user manual and instructions

Product type	Decorative hood
Brand	Faber
Model	The Skypad 2.0
Dimensions (W x D x H)	90 x 50 x 60 cm
Net weight	15 kg
Power supply	220-240 V / 50-60 Hz
Motor power	200 W
Maximum extraction power	650 m³/h
Noise level	55 dB (normal speed)
Energy class	A
Number of speeds	3
Lighting	Integrated LED
Control type	Touch
Grease filter	Dishwasher-safe aluminium
Charcoal filter	Optional, replacement recommended every 6 months
Operating mode	Extraction or recirculation
Maintenance	Clean grease filters regularly; replace charcoal filter
Safety	Automatic shut-off, overheat protection
Spare parts available	Motor, filters, bulbs, control panel
Warranty	2 years
Included accessories	Connection duct, mounting kit, user manual

Frequently Asked Questions - The Skypad 2.0 FABER

How to install the The Skypad 2.0 hood?

Installation must be carried out by a qualified professional. Fix the hood to the wall using the supplied mounting kit, respecting a safety distance of at least 65 cm above an electric hob or 75 cm for a gas hob. Connect the exhaust duct if you choose extraction mode.

What is the difference between extraction and recirculation mode?

In extraction mode, the air is expelled outside via a duct. In recirculation mode, the air is filtered through a charcoal filter and then returned to the room. Recirculation requires the separate purchase of the charcoal filter.

How to clean the grease filters?

The aluminium grease filters can be cleaned in the dishwasher (cycle at max 65°C) or by hand with a non-abrasive sponge and detergent. Let them dry completely before putting them back. Regular cleaning (every 2 months) is recommended.

When should the charcoal filter be replaced?

The charcoal filter should be replaced approximately every 6 months, or more often if the hood is used intensively. A saturated filter reduces recirculation efficiency and may cause odors.

How to adjust the hood speed?

Use the touch controls on the front panel. Press the speed button to select speed 1, 2, or 3. Speed 3 is the most powerful and noisy, reserved for strong vapor emissions.

What to do if the hood does not turn on?

First check the power supply (fuse, circuit breaker). Make sure the plug is properly connected. If the problem persists, contact Faber customer service. Do not attempt to repair it yourself.

How to replace an LED bulb?

The LED bulbs are integrated and must be replaced by an authorized professional. In case of failure, contact Faber after-sales service to obtain a compatible replacement bulb.

Why is my hood making noise?

Excessive noise may come from a clogged grease filter, a poorly fixed duct, or a foreign object in the motor. Clean the filters and check the fixings. If the noise persists, have the appliance checked.

How to activate the automatic shut-off function?

The automatic shut-off function activates after a period of inactivity (usually 10 minutes) to save energy. You can deactivate it via the remote control or control panel settings (see manual).

Where to find the user manual for the The Skypad 2.0 hood?

The manual is included in the packaging. You can also download it for free in PDF format from the official Faber website or on platforms like notice-facile.com. Use the download link on this page.

USER MANUAL The Skypad 2.0 FABER

EN USER MANUAL....3

Recommendations and suggestions

• The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance.
• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
• The minimum safety distance between the cooker top and the extractor hood is 650 mm (some models can be installed at a lower height, please refer to the paragraphs on working dimensions and installation).
• Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply guarantees adequate earthing. Connect the extractor to the exhaust flue through a pipe minimum diameter 120 mm. The route of the flue must be as short as possible.
• Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fire places, etc.).
• If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. The kitchen must

have an opening communicating directly with the open air in order to guarantee the entry of clean air. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0.04 mbar to prevent fumes being drawn back into the room by the cooker hood. - In the event of damage to the power cable, it must be replaced by the manufacturer or by the technical service department, in order to prevent any risks. - If the instructions for installation for the gas hob specify a greater distance specified above, this has to be taken into account. Regulations concerning the discharge of air have to be fulfilled. - Use only screws and small parts in support of the hood. Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards. Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm.

Use

• The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells.
• Never use the hood for purposes other than for which it has been designed.
• Never leave high naked flames under the hood when it is in operation.
• Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.
• Do not flambé under the hood; risk of fire.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• CAUTION: Accessible parts may become hot when used with cooking appliances.

Maintenance

- The symbol ☒ on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling

of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. - Clean and/or replace the Filters after the specified time period (Fire hazard).

- The Activated charcoal filter is not washable and cannot be regenerated, and must be replaced approximately every 4 months of operation, or more frequently for particularly heavy usage (W).

- The Grease filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher (Z).

- Clean the hood using a damp cloth and a neutral liquid detergent.

Controls

Button	Function Led
L	Turns the lights ON/OFF at maximum intensity.	-
	Press and hold the button for approximately 4 seconds, with all the loads turned off (Motor and Lights), to turn the Activated Charcoal Filter alarm on/off.	LED S1 flashes twice = alarm ON.
T1	Turns the motor on/off at speed one.	-
	Press and hold the button for approximately 2 seconds, with all the loads turned off (Motor and Lights), to reset the Activated Charcoal Filter alarm.	LED S1 turns OFF (Fixed or Flashing).
S1	Signals the Metal Grease Filter saturation alarm, indicating that it is necessary to wash the filters. The alarm is triggered after the Hood has been in operation for 100 working hours.	Fixed
	When this is activated, it signals the Activated Charcoal Filter saturation alarm, indicating that the filter must be changed; the Metal Grease Filters must also be washed. The Activated Charcoal Filter saturation alarm comes into operation after the Hood has been working for 200 hours.	Flashing

Remote control

The appliance can be controlled using a remote control powered by a 1.5 V carbon-zinc alkaline batteries of the standard LR03-AAA type (not included).

• Do not place the remote control near to heat sources. • Used batteries must be disposed of in the proper manner.

Button	Function Display
	Turns the Motor On/Off. -
-	Decreases the speed of the Motor. -
+	Increases the speed of the Motor.	-
i	INTENSIVE- Activates Intensive speed from any other speed.To disable it, simply press the same button again or turn the motor off.- Intensive speed is timed to run for 6 minutes. At the end of the 6 minutes the system automatically returns to the speed set previously.	-
	Press briefly for the Delay Function:Can only be activated if the Intensive or 24h function is not active.Activates and deactivates total shutdown of the hood (motor+lights) after 30 minutes:To disable the Delay, simply press the button again or turn the motor off.	The led on the motor button (on the hood controls) will flash once every 0.5 seconds.
	Press and hold for 2sec for the 24H Function:Can only be activated if the Intensive or Delay function is not active.Activates and deactivates the 24H function for 10 minutes every hour, for 24 hours. After this time it is deactivated.	The led on the motor button (on the hood controls) will flash once every 2 seconds.
	Turns the Hood lights On/Off at maximum intensity.	-
	Press and hold for 2sec to turn the Hood lights On/Off at reduced intensity.	-

Lighting

- For replacement contact technical support ("To purchase contact technical support").

ar

Tipka	Funkcija Led
	Uključuje/isključuje motor. -
-	Smanjuje brzinu motora. -
+	Povećava brzinu motora.	-
[6K1W]	INTENZIVNA- Aktivira intenzivnu brzinu s bilo koje brzine.Za isključivanje je dovoljno ponovno pritisnuti istu tipku ili isključiti motor.- Intenzivna brzina je tempirana na 6 minuta.Po isteku 6 minuta, sustav se automatski vraća na prethodno postavljenu brzinu.
[3440]	Kratko pritisnuta funkcija Delay:Može se aktivirati samo kad nije aktivna Intenzivna ili 24h.Aktivira i deaktivira način potpun zaustavljanja nape (motor + svjetla) nakon 30 minuta:Za isključivanje funkcije Delay može se ponovno pritisnuti ista tipka ili isključiti motor.	Led prisutan na tipki motora (komandi nape) bljeska svake 0,5 sekunde.
	Ako se drži pritisnuta 2 sekunde funkcija 24h:Može se aktivirati samo kad nije aktivna Intenzivna ili Delay.Aktivira i deaktivira funkciju 24 na 10 minuta svaki sat, 24 sata.Po isteku tog vremena se deaktivira.	Led prisutan na tipki motora (komandi nape) bljeska svake 2 sekunde.
[6K102]	Uključuje/isključuje svjetla nape na maksimalni intenzitet.	-
	Ako se drži pritisnuta 2 sekunde uključuje/isključuje svjetla nape na smanjeni intenzitet.	-

Lighting

- For replacement, contact technical support ("For purchase, contact technical support").

ih

MO-