C847IS-P33, C847MS-E33 - Motherboard MSI - Free user manual and instructions

Product Type	Mini-ITX Motherboard
Brand	MSI
Model	C847IS-P33, C847MS-E33 (MS-7836 series v1.x)
Integrated Processor	Intel Celeron 847 (dual-core, 1.1 GHz) for C847IS-P33; Intel Celeron 807 (single-core, 1.5 GHz) for C807IS-P33
Chipset	Intel NM70
Supported Memory	2 x DDR3 DIMM, up to 16 GB, DDR3 1333/1066, dual channel
LAN	Realtek RTL8111E, 10/100/1000 Mbps
Audio	Realtek ALC887, HD Audio, 3 jack ports
SATA Storage	1 x SATA 6 Gb/s, 1 x SATA 3 Gb/s
Rear Panel Connectors	1x PS/2 keyboard, 1x PS/2 mouse, 4x USB 2.0, 1x RJ45, 1x VGA, 1x DVI-D, 3x audio
Internal Connectors	2x USB 2.0, 1x front audio, 1x TPM, 1x chassis intrusion
Expansion Slots	1x PCIe 2.0 x1
Form Factor	Mini-ITX (17.0 cm × 17.0 cm)
Power Requirement	ATX 24-pin + ATX 4-pin 12V connector
Estimated Weight	0.5 kg (motherboard only)
Security	CMOS jumper, chassis intrusion detection, TPM support
Maintenance	Clean with a dry, lint-free cloth; avoid moisture and chemicals
Repairability	Spare parts and documentation available on MSI website; replacement board if defective
General Information	Compatible with Windows XP (IDE mode required); BIOS with advanced options; manual available in multiple languages

Frequently Asked Questions - C847IS-P33, C847MS-E33 MSI

How to install memory modules on this motherboard?

Unlock the DIMM slot by spreading the side clips. Insert the module vertically aligning the notch. Push firmly until the clips close with a click. For dual-channel mode, install two modules of the same type and density in slots of the same color.

How to clear the CMOS to reset the BIOS?

Turn off the computer. Move the JBAT1 jumper from 'Keep' to 'Clear' for a few seconds, then return it to the original position. Avoid clearing the CMOS while the system is on.

Which processor is supported by the C847IS-P33 motherboard?

The C847IS-P33 model integrates an Intel Celeron 847 dual-core processor clocked at 1.1 GHz. The C807IS-P33 model integrates an Intel Celeron 807 single-core at 1.5 GHz. Both use the Intel NM70 chipset.

How to install Windows XP on this motherboard?

To install Windows XP, you must first configure the BIOS: go to Advanced > SATA Mode and set it to IDE (not AHCI). Then save and reboot. Proceed with installation normally. After installation, you can switch to AHCI mode if needed.

Where to find drivers and BIOS updates?

You can download drivers and BIOS from the official MSI website: http://www.msi.com/service/test-report or the model's support page. Use the M-Flash utility in the BIOS to update the firmware.

How to connect the front panel (buttons and LEDs)?

Use the JFP1 connector on the motherboard. Refer to the diagram in the manual to properly connect the power button, reset button, power LED, and HDD LED cables. The pinout conforms to the Intel Front Panel I/O design.

What to do if the screen stays black at startup?

First check that all power cables (24-pin and 4-pin) are properly connected. Make sure the memory is correctly installed. If the problem persists, clear the CMOS (see question 2) or test with a single memory module. Also check that the monitor is connected to the VGA or DVI-D output.

Does this motherboard support dual-channel memory?

Yes, it supports dual-channel mode. To enable it, install two identical memory modules (same capacity, frequency, and timings) in both DIMM slots. The BIOS will automatically detect dual-channel mode.

How to enable AHCI mode for SATA drives?

Access the BIOS by pressing Del at startup. Go to Advanced > SATA Mode and select AHCI. Save and reboot. Note that Windows XP requires IDE mode; for Windows 7 and later, AHCI is recommended. If you change mode after installation, the system may not boot.

What audio connectors are available?

The board has three audio jack ports (line-in, line-out, microphone) on the rear, and a front audio connector (JAUD1) compatible with Intel. For 8-channel sound, the rear speakers must be connected to the front panel.

USER MANUAL C847IS-P33, C847MS-E33 MSI

The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice.

TRADEMARKS

All trademarks in this manual are properties of their respective owners.

MSI is a registered trademark of Micro-Star Int'l Co., Ltd. NVIDIA® is a registered trademark of NVIDIA Corporation. ATI® is a registered trademark of ATI Technologies, Inc. AMD® is a registered trademark of AMD Corporation. Intel is a registered trademark of Intel Corporation. Windows® is a registered trademark of Microsoft Corporation. AMI® is a registered trademark of American Megatrends, Inc. Award is a registered trademark of Phoenix Technologies Ltd. Sound Blaster® is a registered trademark of Creative Technology Ltd. Realtek® is a registered trademark of Realtek Semiconductor Corporation. JMicron® is a registered trademark of JMicron Technology Corporation. Netware® is a registered trademark of Novell, Inc. Lucid® is a trademark of LucidLogix Technologies, Ltd. VIA is a registered trademark of VIA Technologies, Inc. ASMedia® is a registered trademark of ASMedia Technology Inc. iPad, iPhone, and iPod are trademarks of Apple Inc.

REVISION HISTORY

Revision	Revision History	Date
V1.0	First release for PCB 1.X	2012/ 09

SAFETY INSTRUCTIONS

Always read the safety instructions carefully. Keep this User Manual for future reference. Keep this equipment away from humidity. Lay this equipment on a reliable flat surface before setting it up. The openings on the enclosure are for air convection hence protect the equipment from overheating. Do not cover the openings. Make sure the voltage of the power source is at 110/220V before connecting. Place the power cord such a way that people cannot step on it. Do not place anything over the power cord. Always unplug the power cord before inserting any add-on card or module. All cautions and warnings on the equipment should be noted. Never pour any liquid into the opening that can cause damage or cause electrical shock. If any of the following situations arises, get the equipment checked by service personnel:

The power cord or plug is damaged. Liquid has penetrated into the equipment. The equipment has been exposed to moisture. The equipment does not work well or you cannot get it to work according to the User Manual. The equipment has been dropped and damaged. The equipment has obvious signs of breakage.

DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STORAGE TEMPERATURE ABOVE 60°C (140°F), IT MAY DAMAGE THE EQUIPMENT.

TECHNICAL SUPPORT

If a problem arises with your system and no solution can be obtained from the user's manual, please contact your place of purchase or local distributor. Alternatively, please try the following help resources for further guidance.

Visit the MSI website for technical guide, BIOS updates, driver updates, and other information: http://www.msi.com/service/download

Contact our technical staff at: http://support.msi.com

FCC-B RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Notice 1

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Notice 2

Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.

SEE THE INSTALLATION NOTICE BEFORE CONNECTING TO THE NETWORK.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CE CONFORMITY

Hereby, Micro-Star International CO., LTD declares that this device is in compliance with the essential safety requirements and other relevant provisions set out in the European Directive.

RADIATION EXPOSURE STATEMENT

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment and its antenna should be installed and operated with minimum distance 20 cm between the radiator and your body. This equipment and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

EUROPEAN COMMUNITY COMPLIANCE STATEMENT

The equipment complies with the RF Exposure Requirement 1999/519/EC, Council Recommendation of 12 July 1999 on the limitation of exposure of the general public to electromagnetic fields (0-300GHz). This wireless device complies with the R&TTE Directive.

TAIWAN WIRELESS STATEMENTS

Wireless Equipment Warning Statement

Batteries, battery packs, and accumulators should not be disposed of as unsorted household waste. Please use the public collection system to return, recycle, or treat them in compliance with the local regulations.

Taiwan:

Recycle waste batteries

For better environmental protection, waste batteries should be collected separately for recycling or special disposal.

California, USA:

The button cell battery may contain perchlorate material and requires special handling when recycled or disposed of in California. For further information please visit: http://www.dtsc.ca.gov/hazardouswaste/perchlorate/

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

CHEMICAL SUBSTANCES INFORMATION

In compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No. 1907/2006 of the European Parliament and the Council), MSI provides the information of chemical substances in products at:

http://www.msi.com/html/popup/csr/evmptrtt_pcm.html

Names and contents of hazardous or toxic substances or elements in the product

To protect the global environment and as an environmentalist, MSI must remind you that...

Under the European Union ("EU") Directive on Waste Electrical and Electronic Equipment, Directive 2002/96/EC, which takes effect on August 13, 2005, products of "electrical and electronic equipment"

cannot be discarded as municipal wastes anymore, and manufacturers of covered electronic equipment will be obligated to take back such products at the end of their useful life. MSI will comply with the product take back requirements at the end of life of MSI-branded products that are sold into the EU. You can return these products to local collection points.

GERMAN

Thank you for choosing the C847IS-P33/C807IS-P33 series (MS-7836 v1.x) Mini-ITX mainboard. The C847IS-P33/C807IS-P33 series is designed based on Intel® Celeron 847/807 processor and Intel® NM70 chipset. The C847IS-P33/C807IS-P33 series deliver a high performance and energy saving solution for BOX PCs.

Layout

SPECIFICATIONS

Processor

Intel® Celeron 847/1.1 GHz/Dual-Core processor (C847IS-P33) Intel® Celeron 807/1.5 GHz/ Single-Core processor (C807IS-P33)

Chipset

Intel® NM70 chipset

Memory Support

2x DDR3 DIMMs support DDR3 1333/ 1066 DRAM (16GB Max) Supports Dual-Channel mode

LAN

Supports LAN 10/100/1000 Fast Ethernet by Realtek® RTL8111E

Audio

Integrated HD audio codec by Realtek® ALC887

SATA

1x SATA 3Gb/s port by Intel® NM70 1x SATA 6Gb/s port by Intel® NM70

Connectors & Buttons

Back panel

• 1x PS/2 keyboard port
• 1x PS/2 mouse port
• 4x USB 2.0 ports
• 1x LAN port
• 1x VGA port
• 1x DVI-D port
• 3x Audio ports

On-Board

• 2x USB 2.0 connectors
• 1x Front Panel Audio connector
• 1x TPM Module connector
• 1x Serial connector
• 1x Chassis Intrusion connector

Slots

1x PCIe 2.0 x1 slot

Form Factor

• Mini-ITX (17.0 cm X 17.0 cm)

Mounting Screw Holes

4x mounting holes

REAR PANEL

The rear panel provides the following connectors:

IMPORTANT

To reach the 8-channel sound effect, the 7th and 8th channels must be output from front panel.

For more information on compatible components, please visit http://www.msi.com/service/test-report

If you need to purchase accessories and request the part numbers, you could search the product web page and find details on our web address below http://www.msi.com/index.php

Mounting Screw Holes

When installing the mainboard, first install the necessary mounting stands required for a mainboard on the mounting plate in your computer case. If there is an I/O back plate that came with the computer case, please replace it with the I/O backplate that came with the mainboard package. The I/O backplate should snap easily into the computer case without the need for any screws. Align the mounting plate's mounting stands with the screw holes on the mainboard and secure the mainboard with the screws provided with your computer case. The locations of the screw holes on the mainboard are shown below. For more information, please refer to the manual that came with the computer case.

IMPORTANT

• Install the mainboard on a flat surface free from unnecessary debris.
• To prevent damage to the mainboard, any contact between the mainboard circuitry and the computer case, except for the mounting stands, is prohibited.
• Please make sure there are no loose metal components on the mainboard or within the computer case that may cause a short circuit of the mainboard.

Installing Memory Modules

1. Unlock the DIMM slot by pushing the mounting clips to the side. Vertically insert the memory module into the DIMM slot. The memory module has an off-center notch on the bottom that will only allow it to fit one way into the DIMM slot.
2. Push the memory module deep into the DIMM slot. The plastic clips at each side of the DIMM slot will automatically close when the memory module is properly seated, and an audible click should be heard.
3. Manually check if the memory module has been locked in place by the DIMM slot's side clips.

IMPORTANT

• To ensure system stability, memory modules must be of the same type and density in Dual-Channel mode.
• Due to hardware limitations, you should follow the installing procedures: first memory modules, then graphics card. While uninstalling, remove graphics card first if necessary.

JPWR1: ATX 24-Pin Power Connector

This connector allows you to connect an ATX 24-pin power supply. To connect the ATX 24-pin power supply, align the power supply cable with the connector and firmly press the cable into the connector. If done correctly, the clip on the power cable should be hooked on the mainboard's power connector.

JPWR2: ATX 4-Pin Power Connector

This connector provides 12V power to the CPU.

IMPORTANT

Make sure that all the power cables are securely connected to a proper ATX power supply to ensure stable operation of the mainboard.

CPUFAN, SYSFAN1: Fan Power Connectors

The fan power connectors support system cooling fans with +12V. If the mainboard has a System Hardware Monitor chipset on-board, you must use a specially designed fan with a speed sensor to take advantage of the CPU fan control. Remember to connect all system fans. Some system fans may not connect to the mainboard and will instead connect to the power supply directly. A system fan can be plugged into any available system fan connector.

CPUFAN

SYSFAN1

SATA1~2: SATA Connector

This connector is a high-speed Serial ATA interface port. Each connector can connect to one Serial ATA device. Serial ATA devices include disk drives (HD), solid state drives (SSD), and optical drives (CD/DVD/Blu-Ray).

SATA1 (6Gb/s, by Intel® NM70)

SATA2 (3Gb/s, by Intel® NM70)

IMPORTANT

• Please do not fold the SATA cable at a 90-degree angle. Data loss may result during transmission otherwise.
• SATA cables have identical plugs on either sides of the cable. However, it is recommended that the flat connector be connected to the mainboard for space saving purposes.

JFP1: Front Panel Connector

These connectors are for electrical connection to the front panel switches and LEDs. The JFP1 is compliant with Intel® Front Panel I/O Connectivity Design Guide.

JCOM1: Serial Port Connector

This connector is a 16550A high speed communication port that sends/receives 16 bytes FIFOs. You can attach a serial device.

JUSB1, JUSB2: USB 2.0 Expansion Connectors

This connector is designed for connecting high-speed USB peripherals such as USB HDs, digital cameras, MP3 players, printers, modems, and many others.

JAUD1 : Front Panel Audio Connector

This connector allows you to connect the front audio panel located on your computer case. This connector is compliant with the Intel® Front Panel I/O Connectivity Design Guide.

JCI1: Chassis Intrusion Connector

This connector connects to the chassis intrusion switch cable. If the computer case is opened, the chassis intrusion mechanism will be activated. The system will record this intrusion and a warning message will flash on screen. To clear the warning, you must enter the BIOS utility and clear the record.

JTPM1: TPM Module Connector

This connector connects to an optional TPM (Trusted Platform Module). Please refer to the TPM security platform manual for more details and usages.

JBAT1: Clear CMOS Jumper

There is CMOS RAM onboard that is externally powered from a battery located on the mainboard to save system configuration data. With the CMOS RAM, the system can automatically boot into the operating system (OS) every time it is turned on. If you want to clear the system configuration, set the jumper to clear the CMOS RAM.

Keep Data

Clear Data

IMPORTANT

You can clear the CMOS RAM by shorting this jumper while the system is off. Afterwards, open the jumper. Do not clear the CMOS RAM while the system is on because it will damage the mainboard.

PCIe Slot

The PCIe slot supports the PCIe interface expansion card.

The PCIe 2.0 x1 slot

BIOS SETUP

Power on the computer and the system will start POST (Power On Self Test) process. When the message below appears on the screen, press key to enter Setup.

Press DEL to enter Setup Menu

If the message disappears before you respond and you still wish to enter Setup, restart the system by turning it OFF and On or pressing the RESET button. You may also restart the system by simultaneously pressing , , and keys.

The Menu Bar

Main Menu

Use this menu for basic system configurations, such as time, date etc.

Advanced

Use this menu to set up the items of special enhanced features.

M-Flash

Use this menu to read/ flash the BIOS form storage drive (FAT/ FAT32 format only).

Security

Use this menu to set supervisor and user passwords.

Boot

Use this menu to specify the priority of boot devices.

Save & Exit

This menu allows you to load the BIOS default values or factory default settings into the BIOS and exit the BIOS setup utility with or without changes.

Save & Exit

Discard Changes and Exit

Use this item to abandon all changes and exit setup.

Save Changes and Reboot

Use this item to save changes and reset the system.

Save Changes

Use this item to save changes.

Discard Changes

Use this item to abandon all changes.

Restore Defaults

Use this item to load the optimized default values set by the BIOS vendor.

Boot Override

The installed storage devices will appear on this menu. You can select one of them to be a boot device.

INSTALL WINDOWS XP NOTES

This section describes how to install Windows XP with IDE mode.

Installing Windows XP with IDE Mode

You will fail and encounter a blue screen while installing Windows XP, because it is not natively supported to be installed in the storage device with AHCI mode. If you still prefer to install Windows XP as the operating system, please change the BIOS item as below.

1. Refer to BIOS SETUP chapter to access BIOS.
2. Go to Advanced → SATA Mode.
3. Set the SATA Mode to IDE mode.
4. Go to Save & Exit → Save Changes and Reboot.
5. Install the Windows XP operating system.

Intel® NM70 SATA 3Gb/s 1 port, Intel® NM70 SATA 6Gb/s 1 port

K

-

- PS/2 keyboard 1, PS/2 mouse 1, USB 2.0 4 ports, LAN 1 port, VGA 1, DVI-D 1, Audio I/O 3

PCIe slots

PCIe slots are also supported by the Intel chipset.

PCIe 2.0 x1 slots

The system BIOS is stored in the flash ROM and is activated during POST (Power-On Self Test).

Press DEL to enter Setup Menu

(DEL)

Discard Changes and Exit

i

Save Changes and Reboot

Discard Changes and Exit

• Mini-ITX (17.0 cm × 17.0 cm)

Discard Changes and Exit

SYSTEM COMPONENTS

SPECIFICATIONS

Processor Check

• Processor Intel® Celeron 847/1.1 GHz/Dual-core (C847IS-P33)
• Processor Intel Celeron 807/1.5 GHz/Single-core (C807IS-P33)

Chipset

Intel® NM70

Memory

2x DDR3 DIMMs with support for DDR3 1333/1066 DRAM modules (Maximum capacity 16GB) Support for dual-channel mode

LAN

Supports LAN 10/100/1000 Fast Ethernet based on Realtek RTL8111E

Audio

Built-in HD audio codec Realtek® ALC887

SATA

1x SATA 3Gb/s port on Intel® NM70 1x SATA 6Gb/s port on Intel® NM70

Connectors and headers

Rear panel

• 1x PS/2 keyboard port
• 1x PS/2 mouse port
• 4x USB 2.0 ports
• 1x LAN port
• 1x VGA port
• 1x DVI-D port
• 3x audio jacks

Onboard headers

• 2x USB 2.0 headers
• 1x audio header on front panel
• 1x TPM module header
• 1x serial port connector
• 1x chassis intrusion connector

Slots

1x PCIe 2.0 x1 slot

Form Factor

Mini-ITX (17.0 cm x 17.0 cm)

Mounting Holes

4x mounting holes

Rear Panel

The rear panel contains the following connectors:

NOTE

To enable 7.1-channel audio, you must connect audio jacks to the front panel.

For more information on compatible components, please visit

http://www.msi.com/service/test-report

To purchase additional accessories, please visit the MSI website.

Mounting Screws

When installing the motherboard, first install the motherboard standoffs on the chassis. If the chassis comes with an I/O shield, replace it with the I/O shield included with the motherboard. The standoffs are easily placed in the chassis and do not require screws. Align the standoffs with the mounting holes on the motherboard and secure the motherboard with the screws provided with the chassis. The location of the mounting holes on the motherboard is shown below. For additional information, refer to the chassis manual.

WARNING

* The motherboard should be installed on a flat surface free of debris. * To avoid damage to the motherboard, its electrical circuit should not come into contact with the chassis. This is achieved with the mounting standoffs. * Ensure that all metal components on the motherboard and the chassis screws are properly secured. Otherwise, a short circuit may occur and damage the motherboard.

Installing Memory Modules

1. Push the DIMM slot clips outward. Insert the memory module into the DIMM slot vertically. The memory module has a notch off-center, which allows it to be inserted into the DIMM slot only in one specific orientation.
2. Insert the memory module firmly until it clicks into place. When properly installed, the plastic clips on both sides of the slot will automatically close with a distinct click.
3. Manually verify that the module is secured in the DIMM slot by the clips on both sides.

WARNING

* For stable system operation, use memory modules of the same type and capacity. * Due to hardware limitations, follow these installation instructions: First install the memory modules, then the graphics card. If you need to remove the graphics card, do so first if necessary.

JPWR1: 24-pin ATX Power Connector

This connector allows you to connect a 24-pin ATX power supply. Before connecting the power supply, ensure that its power connector is oriented correctly on the motherboard. Then firmly insert it into the connector on the system board. When properly connected, the latch on the power cable should secure the cable in the motherboard connector.

JPWR2: 4-pin ATX Power Connector

This connector is used to provide power to the processor (12V).

Make sure that all power connectors are properly connected.

CPUFAN, SYSFAN1: Fan power connectors

For fan power connectors, installation of fans with +12V power is allowed. If the system board has a system monitoring connector, it is recommended to use specially designed fans with speed sensors to control the fan speed of the processor. Do not forget to connect all system fans. Some system fans cannot be connected to the system board. Instead, they are connected to the power supply directly. The fan can be connected to any free fan connector on the system.

CPUFAN

SYSFAN1

SATA1~2: SATA connector

Option Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Main Menu Advanced H-Flash Security, Boot Save & Exit
Discard Changes and ExitSave Changes and RebootSave OptionsSave ChangesDiscard ChangesRestore DefaultsBoot OverrideUEFI: Built-In EFI Shell	Exit systen setup withoutsaving any changes.

Discard Changes and Exit

Discard Changes and Exit

Use this option to discard all changes and exit the setup.

Save Changes and Reboot

Use this option to save changes and reboot the system.

Save Changes

Use this option to save changes.

Discard Changes

Use this option to discard all changes.

Restore Defaults

1 PCIe 2.0 x1 slot

Dimensions

Optic Setup Utility - Copyright (C) 2011 American Megafrends, Inc.
Main Menu Advanced H-Flash Security Boot Save & Exit
Discard Changes and ExitSave Changes and RebootSave OptionsSave ChangesDiscard ChangesRestore DefaultsBoot OverrideUEFI: Built-In EFI Shell	Exit systen setup withoutsaving any changes.

Discard Changes and Exit

This item is used to discard all changes and exit the setup screen.

Save Changes and Reboot

This item is used to save changes and then reboot.

Save Changes

This item is used to save changes.

Discard Changes

This item is used to discard all changes.

Restore Defaults

Discard Changes and Exit

Save changes and exit.

Save Changes and Reboot