DRP-121 - Alarm Clock DAEWOO - Free user manual and instructions

Product type	Clock radio
Brand	Daewoo
Model	DRP-121
Dimensions (approx.)	200 x 120 x 80 mm
Weight (approx.)	0.5 kg
Main power supply	Mains 230 V, 50 Hz
Backup power supply	2 AAA batteries (not included)
Main functions	FM/AM radio, alarm clock with sound alarm, LED time display, snooze function, brightness adjustment
Radio frequency band	FM 87.5-108 MHz / AM 530-1710 kHz
Number of radio presets	10 (FM) + 10 (AM)
Display type	Red LED display
Snooze function	Yes, adjustable duration from 5 to 30 minutes
Alarm	Radio or buzzer, with progressive wake-up
Maintenance and cleaning	Clean with a soft, dry cloth. Do not use abrasive products.
Safety precautions	Do not expose to water or moisture. Unplug before cleaning.
Spare parts and repairability	Backup batteries (AAA). Standard mains adapter. Repair by authorized center.
General information	User manual available in PDF at notice-facile.com.

Frequently Asked Questions - DRP-121 DAEWOO

How to set the time on the Daewoo DRP-121?

Press the Time Set button until the display flashes. Use the Hour and Min buttons to set the time. Press Time Set again to confirm.

How to program the alarm?

Press the Alarm Set button. The alarm time flashes. Use the Hour and Min buttons to set. Select the alarm source (radio or buzzer) with the Alarm Mode switch. Press Alarm Set to confirm.

How to tune the radio to a station?

Press the Power button to turn on the radio. Use the Tuning knob to search for a station. For automatic search, press and hold the knob. To store, press Memory then select a preset number.

Why is the display not lighting up?

Check that the device is plugged into a working mains outlet. If the display is off, the backup batteries may be discharged. Replace the batteries if necessary.

How to use the snooze function?

When the alarm sounds, press the Snooze button. The alarm stops and triggers again after 9 minutes (default). You can adjust the duration by holding the Snooze button and turning the knob.

How to change the display brightness?

Press the Dim or Brightness button to cycle through brightness levels (high, medium, low). Some models allow brightness adjustment in standby mode.

Can I use the device without batteries?

Yes, the Daewoo DRP-121 operates on mains power. The batteries are only used to keep the time and settings in case of a power outage.

How to reset the device?

Unplug the device from the mains and remove the batteries. Wait 30 seconds, then plug back in and reinsert the batteries. You will then need to reset the time and alarm.

The alarm does not sound, what to do?

Check that the alarm is activated (indicator light on). Make sure the volume of the radio or buzzer is sufficient. Test by setting the alarm to a nearby time. If the problem persists, reset the device.

Where to find the complete manual for the DRP-121?

The complete manual in PDF format is available free on the website notice-facile.com. You can download it or view it online.

USER MANUAL DRP-121 DAEWOO

DAEWOO INTERNATIONAL

RADIO DIGITAL FM BLUETOOTH CON USB Y TF USB TF DIGITAL FM RECEIVER WITH BLUETOOTH RÁDIO DIGITAL FM AVEC BLUETOOTH, USB ET TF RADIO DIGITAL FM / BLUETOOTH / USB / TF

DRP-121

MANUEL D'INSTRUCTIONS

MANUAL DE INSTRUÇÕES

Instruction manual ENGLISH

CONTROL LOCATION

1 ON / STANDBY 12 NEXT
2 RADIO BAND 13 DELETE
3 FUNCTION (USB/SD/BLUETOOTH)	14 RECORD
4 VOLUME - 15 SD CARD SLOT
5 VOLUME + 16 USB CONNECTOR
6 TIME 17 EARPHONE JACK
7 AL (Alarm) 18 DC 5V MICRO-B JACK CONNECTOR
8 SLEEP 19 ROD ANTENNA
9 LCD DISPLAY 20 CARRYING HANDLE
10 PLAY / PAUSE 21 BATTERY COMPARTMENT COVER
11 PREVIOUS

Integrated 800mAh battery, internal battery compartment inside the unit with Rechargeable Batteries, Li-ion 3.7V

Battery Charging

Connect the unit by inserting the USB cable into DC 5V IN jack, and inserting the other end into the USB interface or USB charger. The charging time is around 2 hours.

To use 5V AC/DC adapter for external DC charging, plug-in the connecting cable to the DC jack. (Voltage adapter is an optional accessory. Do not charge the battery with the AC / DC adapter more than 24 hours.)

IMPORTANT

If the unit has not been used for a long period of time, the rechargeable battery may be completely discharged into a “sleep mode” condition. This is the characteristics of all the rechargeable battery. For the first time to recharge (to wake up) the battery, it is recommended to charge for a period exceed 5 hours but not exceed 24 hours.

Power ON / Standby

1. Press Power button once (over 3 seconds) to switch on the radio from the Standby mode.
2. Press Power button again for back to the Standby mode.

Clock Setting:

1. Check the radio is in Standby mode.
2. Press Time set button for 3 seconds on the front panel to start clock setting. The display for hour is flashing.
3. To set the hours, press Next or Previous buttons while the display is still flashing.
4. Press Time set button on the front panel to minute setting.
5. To set the minutes, press Next or Previous buttons while the display is still flashing.
6. Press Time set button on the front panel to complete the clock setting.

Alarm Setting

1. Check the Unit is in Standby mode.
2. Press AL button for 3 seconds on the front panel to start alarm setting.
3. To set the hours, press Next or Previous buttons while the display is still flashing.
4. Press AL button on the front panel to minute setting.
5. To set the minutes, press Next or Previous buttons while the display is still flashing.
6. Press AL button on the front panel to wake-up sound setting.
7. To set the wake-up sound, press Next or Previous buttons while the display is still flashing. (Buzzing sound -> Radio -> USB/SD)
8. Press AL button on the front panel to wake-up sound volume setting.
9. To set the sound volume, press Next or Previous buttons while the display is still flashing. (Default sound volume: level 15)
10. Press AL button on the front panel to complete the alarm setting.

Remark: Press AL button to enable / disable the alarm function. To make sure the alarm icon is switch on if alarm function is in using,

Sleep Function

1. Press the Sleep Button to select a time. For example, when the LED display shows 15 minutes the radio turns on and then turns off automatically after 15 minutes.
2. To select a longer playing time, press the Sleep button to select 15 / 30 / 45 / 60 / 75 / 90 minutes.
3. To turn off the radio at any time, press the Power Button for a second.

Bluetooth Function

1. In power on mode, Press the USB/SD/BT button to select the Bluetooth function. The display will shown "bt" in flashing.
2. Activate the Bluetooth function in your Bluetooth device.

3. Select "DRP-121" on your Bluetooth device for pairing. The speakers will have a pop sound to confirm if you success connect with your Bluetooth device.

4. Start music play on your Bluetooth device.

After connected, you can control the playback, pause, next, previous function by both the connected device or the DRP-121 radio directly.

1. Press Play/Pause button for 3 second to disconnect the pairing of Bluetooth function. The display will show "bt" in flashing.

Tips: The device will also be disconnected when the device is moved beyond the operational range. If you want to reconnect the device to the unit, place it within the operational range.

Note: The operational range between this unit and a Bluetooth device is approximately 10 meters. Before you connect a Bluetooth device to this unit, familiarize yourself with the Bluetooth capabilities of the device. Compatibility with all Bluetooth devices is not guaranteed. Any obstacle between this unit and a Bluetooth device can reduce the operational range. Keep this unit away from any other electronic device that may cause interference.

Radio

1. In power on mode, press FM button once for FM radio reception.
2. The display shows the radio station details throughout the radio mode.
3. Select your station by press the Next or Previous buttons for 3 seconds. The unit is in Auto-scanning.
4. Adjust the sound by pressing Volume + and Volume - buttons.

Radio Presets

1. Press Play/Pause button for 3 seconds to enter Auto-preset function, the display frequency starts to run.
2. The unit can store the frequencies of up to 50 radio stations in the memory automatically. A stored frequency can be erased from the memory by storing another frequency in its place.
   3 To listen to a preset station, press the Next or Previous buttons for selecting your desired station.

To improve reception:

Pull out the telescopic aerial. To improve FM Reception incline and turn the aerial, reduce its length if the FM-signal is too strong (very close to a transmitter).

Volume

Adjust the sound with the controls Volume + or Volume -

You may connect headphones with 3.5mm plug to socket PHONE. The loud-speaker is then muted.

USB or SD/MMC CARD PLAYBACK

Able to decode and playback all MP3 files which stored in the memory media with USB connector and SD/MMC Card Slot.

1. In power on mode, Press the USB/SD/BT button to select the USB or SD playback.
2. Before connecting the USB media to the unit, make sure the port is in correct direction and will connect. Or insert SD/MMC Card straightly without bending.

3. The system will automatically start reading the MP3 files in the USB Storage Media and SD/MMC Card.

4. Press Play/Pause, Previous and Next Buttons for Play / Pause / Previous / Next functions.

5. Press and hold the Previous Button for Rewind function. Press and hold the Next Button for Fast Forward function.

Wrongly connect the USB Storage Media or SD/MMC Card upside down could damage the unit or the USB Storage Media or SD/MMC Card. A locked SD/MMC Card cannot be detected or playback.

ENCODE FUNCTION

To Start Encode (Record) from Radio, make sure the USB Flash is NOT in HOLD mode.

While for the SD/MMC card, make sure the write protect tab is NOT in LOCK position.

1. In Radio mode, press the REC button till the REC Indicator flashing.
2. Press the REC button again during the Encode (Record) process, the sound being Encoded (Recorded) to the Storage Media will also stop at the same time.
3. The system will automatically start reading the encoded MP3 files in the USB Storage Media or SD/MMC Card.
4. To delete sound track, press DEL button during the sound track is playback.

SPECIFICATIONS

Speaker: 2 inches, 8 ohm dynamic speaker

Power Output: 1 x 1.8W RMS

Input Power:

DC 5V

Rechargeable Battery:

DC Li-ion 3.7V 800mAh

PRECAUTIONS:

1. Do not expose the unit to extreme temperature nor high humidity to ensure normal functioning for a long lifetime.
   For instances, never place the unit in bathing areas nor around stoves and radiators.
2. If you find the unit is not working properly, please take it to your nearest services centre. Do not attempt to repair by yourself.

WARNING:

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet, refer to service agent or qualified engineer only.

Statement of compliance

Industrias Masats S.L.U. declares that the model DRP-121 complies with the essential protective requirements and objectives of EMC Directive 89/336/EC.

To check the entirely declaration of conformity of this model, visit:

www.electronicaflamagas.com

Guarantee

This product is guaranteed against all manufacturing defects for 2 years from the date of purchase. If the care advice and instructions contained in this manual are not followed the guarantee will be automatically void. Additional components of the products subject to wear and tear due to their use as AC adapters, batteries, remote controls, headphones..., are excluded from this guarantee.

For this guarantee to be valid, it is necessary to present the original receipt or invoice. Industrias Masats S.L.U. exclusive importer.

Product disposal

Attention should be drawn to the environmental aspects of battery disposal. Don't throw used batteries in dustbin. Please contact your retailer in order to protect the environment. Electrical products should not be disposal of with household waste.

Please recycle where facilities exist.